Re: fireqos status shows ERROR ERROR ERROR

Thanks Mathias!

Well, you can add whatever you like in netdata. Check the
charts.d.plugin. If you know what to add and where to find the source
info, open a github issue in netdata and I'll help you write it.

A good example to start with is `charts.d/squid.chart.sh`.

Costa

PS: I added firehol-support back, so that others can benefit from our
discussion.


On Sat, Sep 26, 2015 at 10:24 PM, Mathias Schulze <[email protected]> wrote:
> Hi Costa,
>
> you were right: no more ERRORs when starting fireqos from /etc/ppp/ip-up.d/
>
> Your netdata is great!!!
>
> It would be nice if it could show some information on dhcp leases and
> corresponding wifi signal strenghts.
>
> Thanks,
> Mathias
>
>
> On 09/24/2015 10:01 PM, Tsaousis, Costa wrote:
>> Hi Mathias,
>>
>> Do you leave it running in 'status' mode for a few hours and suddenly
>> it shows ERROR?
>>
>> If this is the case, then most probably the ppp device it monitors has
>> been disconnected (and probably re-connected), but FireQOS has not
>> been re-applied on the re-connected interface yet (QoS is vanished if
>> the interface drops). If you run 'fireqos start' from
>> /etc/ppp/ip-up.d/ then FireQOS will be restarted on the re-connected
>> interface and the 'status' task you run will most probably show a few
>> lines with ERROR and then catch up again.
>>
>> Keep in mind that you can permanently visualize QoS (among hundreds of
>> other Linux system values) with netdata
>> (https://github.com/ktsaou/netdata). This one will give you nice web
>> charts. Check the github page. I recently added a few links to live
>> demos of netdata running.
>>
>> Costa
>>
>>
>>
>> On Thu, Sep 24, 2015 at 10:49 PM, Mathias Schulze <[email protected]> wrote:
>>> Hi,
>>>
>>> I use version 2.0.3+ds-1 on a debian machine and I regularly get the
>>> errors below after fireqos was running for a few hours. From what I read
>>> in the list archives such a problem appeared to have been fixed?
>>>
>>> Any help is very much appreciated! I can submit config or other info as
>>> needed.
>>>
>>> Thanks!
>>> Mathias
>>>
>>>
>>> root@apu:/home/mschulze# fireqos status world-out
>>> FireQOS 2.0.3
>>> (C) 2013-2014 Costa Tsaousis, GPL
>>>
>>>
>>> world-out: ppp0 output => ppp0, type: adsl, overhead: 40
>>> Rate: 800Kbit/s, min: 12Kbit/s
>>> Values in Kbit/s
>>>
>>>  CLASS   voip realti    vpn surfin defaul
>>> CLASSI   1:11   1:12   1:13   1:14 1:5000
>>> COMMIT    150     40    160    160     12
>>>    MAX    800    800    800    800    800
>>>
>>> PRIORI      4      4      4      4      4
>>>  QDISC  pfifo fq_cod fq_cod fq_cod fq_cod
>>>
>>>  color code (packets):  backlog  |  dropped  |  delayed  |  requeued
>>>  Class Utilization on world-out (ppp0 output => ppp0) - values in Kbit/s
>>>  TOTAL   voip realti    vpn surfin defaul
>>>  ERROR  ERROR  ERROR  ERROR  ERROR  ERROR
>>>  ERROR  ERROR  ERROR  ERROR  ERROR  ERROR
>>>  ERROR  ERROR  ERROR  ERROR  ERROR  ERROR
>>>  ERROR  ERROR  ERROR  ERROR  ERROR  ERROR
>>>
>>> _______________________________________________
>>> Firehol-support mailing list
>>> [email protected]
>>> http://lists.firehol.org/mailman/listinfo/firehol-support
_______________________________________________
Firehol-support mailing list
[email protected]
http://lists.firehol.org/mailman/listinfo/firehol-support