Re: Snort3 installation problem on Ubuntu 20.04 : CMake Error: The following variables are used in this project, but they are set to NOTFOUND

Dear Dave,


There is a new version of snort if you want,

For daq I advice to download it from the official page web snort,

I hope your success,

Thanks you in advance for your answer,

Regards.


Dorian Rosse.
________________________________
From: Dave / Dalek Zone <[email protected]>
Sent: Saturday, May 28, 2022 11:00:52 AM
To: Dorian ROSSE <[email protected]>
Cc: [email protected] <[email protected]>; Joel Esler <[email protected]>
Subject: Re: [Snort-users] Snort3 installation problem on Ubuntu 20.04 : CMake Error: The following variables are used in this project, but they are set to NOTFOUND

Hello Dorian, guys,

Thanks for you rreply. My flex is installed from the apt package (2.6.4)

The version of Snort 3 I tried to compile is 3.1.28.0.

gperftools is 2.9 from Github (manually compiled).

Libdaq is also cloned from git.

With all best wishes,

Dave


On 2022-05-28 10:15, Dorian ROSSE wrote:
> Dear Dave,
>
>  I have too Ubuntu focal 20.04 if you happen a problem with flex this
> isn't for all people because my flex works good but I haven't try to
> built flex with snort,
>
>  I can help you if you want the weekend only because the week I
> haven't a computer,
>
>  Because you use the package flex this isn't built with cmake you can
> forgot my e-mail previous,
>
>  This is interesting because on my snort I haven't try to built flex I
> will try but this weekend I am in holiday sorry I haven't access to my
> system Ubuntu,
>
>  What version of snort you try to built ?
>
>  Dear Joel this person try to built flex with snort can you share with
> us what is the location of flex installation on a system linux or can
> you answer what is the goal of flex on snort because there are some
> flex on GitHub but I don't understand what flex take, (I can run
> 'locate flex' but work a flex from GitHub can be interesting and a
> gflex packaged isn't a program installed on the snort source),
>
>  Thanks you in advance Joel,
>
>  Thanks you in advance for your question Dave,
>
>  Regards.
>
> Dorian Rosse.
> -------------------------
>
> From: Dave / Dalek Zone <[email protected]>
> Sent: Saturday, May 28, 2022 12:11:34 AM
> To: Dorian ROSSE <[email protected]>
> Cc: [email protected] <[email protected]>
> Subject: Re: [Snort-users] Snort3 installation problem on Ubuntu 20.04
> : CMake Error: The following variables are used in this project, but
> they are set to NOTFOUND
>
> Hello Dorian,
>
> Thank you for your reply. I have Flex installed from the current apt
> package (version 2.6.4) on Ubuntu 20.04, whereas I downloaded Snort3
> via
> 'wget
> https://github.com/snort3/snort3/archive/refs/tags/3.1.28.0.tar.gz'
>
> Similarly, gperftools is installed manually via 'wget
> https://github.com/gperftools/gperftools/releases/download/gperftools-2.9/gperftools-2.9.tar.gz'
>
> Libdaq is also cloned from git (and compiled manually): 'git clone
> https://github.com/snort3/libdaq.git'
>
> The various other dependencies are installed via apt: 'apt install
> build-essential libpcap-dev libpcre3-dev libnet1-dev zlib1g-dev luajit
>
> hwloc libdnet-dev libdumbnet-dev bison flex liblzma-dev openssl
> libssl-dev pkg-config libhwloc-dev cmake cpputest libsqlite3-dev
> uuid-dev libcmocka-dev libnetfilter-queue-dev libmnl-dev autotools-dev
>
> libluajit-5.1-dev libunwind-dev'
>
> I will carefully re-read your message and Adrian Mamolea's message in
> the coming hours, and will write back to the list. Thank you again,
> guys, for your help.
>
> With all best wishes,
>
> Dave
>
> On 2022-05-27 19:08, Dorian ROSSE via Snort-users wrote:
>> Dear adrian and dave,
>>
>>
>> I should understand good cmake,
>>
>> Does flex is build with cmake or you speak about snort ?
>>
>> If flex is build with cmake from what location do you download flex
>> because from my setup this is download by way packaged ?
>>
>> Thank you in advance for your answer,
>>
>> Regards.
>>
>>
>> Dorian rosse.
>>
>> -----Message d'origine-----
>> De : Snort-users <[email protected]> De la part de
>> [email protected]
>> Envoyé : vendredi 27 mai 2022 14:00
>> À : [email protected]
>> Objet : Snort-users Digest, Vol 60, Issue 18
>>
>> Send Snort-users mailing list submissions to
>>        [email protected]
>>
>> To subscribe or unsubscribe via the World Wide Web, visit
>>        https://lists.snort.org/mailman/listinfo/snort-users
>> or, via email, send a message with subject or body 'help' to
>>        [email protected]
>>
>> You can reach the person managing the list at
>>        [email protected]
>>
>> When replying, please edit your Subject line so it is more specific
>> than "Re: Contents of Snort-users digest..."
>> _______________________________________________
>> Snort-users mailing list
>> [email protected]
>> Go to this URL to change user options or unsubscribe:
>> https://lists.snort.org/mailman/listinfo/snort-users
>>
>>        To unsubscribe, send an email to:
>>        [email protected]
>>
>> Please visit http://blog.snort.org to stay current on all the latest
>
>> Snort news!
>>
>> Please follow these rules:
>> https://snort.org/faq/what-is-the-mailing-list-etiquette

_______________________________________________
Snort-users mailing list
[email protected]
Go to this URL to change user options or unsubscribe:
https://lists.snort.org/mailman/listinfo/snort-users

	To unsubscribe, send an email to:
	[email protected]

Please visit http://blog.snort.org to stay current on all the latest Snort news!

Please follow these rules: https://snort.org/faq/what-is-the-mailing-list-etiquette