RE: RE: Password not accepted since last changed

Yes, that's exactly what I needed to do.  Thanks

> -----Original Message-----
> From:	Michael Naughton [SMTP:mnaughton-ASFSQzaE8w1Wk0Htik3J/[email protected]]
> Sent:	Thursday, September 04, 2003 4:42 PM
> To:	CODE/400 Discussion & Support
> Subject:	Re: RE: Password not accepted since last changed
> 
> I'm pretty sure I just had exactly the same problem you're experiencing. I
> solved it by going to Start/Programs/IBM Websphere Studio Client for
> iSeries/Communications/Define Server Logon. That gave me a window showing
> my logon name; when I selected it, the "Change" button became activated. I
> simply clicked that button and put in my new password.
> 
> (of course, it had taken me two days to figure out that that's what I
> needed to do. . . . ;-)
> 
> hth
> 
> CODE/400 Discussion & Support <code400-l-Zwy7GipZuJhWk0Htik3J/[email protected]> writes:
> >> From:	Mark Keller [SMTP:mkeller-L/[email protected]]
> >> did you perhaps put the password into your strcode command?  I am
> >guessing
> >> that could be your problem?
> >> 
> > No, the password is not in the strcode command, simply because I don't
> >use
> >STRCODE.  I'm on V5R2, which does not require it.
> >
> >
> >> From: Wills, Mike N. (TC) [mailto:[email protected]]
> >> It is in the communication daemon down by your clock in Windows
> >> 
> >	[Johnson, Duane]  I suppose it's possible that it's contained in the
> >communication daemon, but if so, I can't get there to change it, nor
> >could I
> >have gotten there to put it there in the first place.  When I try to
> bring
> >up "Properties"  I get the busy signal (hourglass) for a few seconds then
> >nothing more.  It has been that way ever since I've had this computer.
> >
> >	I'm pretty sure that it was either a macro that I modified or a
> >command line change, but I don't remember which.
> >>  
> 
> 
> Mike Naughton
> Senior Programmer/Analyst
> Judd Wire, Inc.
> 124 Turnpike Road
> Turners Falls, MA  01376
> 413-863-4357 x444
> mnaughton-ASFSQzaE8w1Wk0Htik3J/[email protected]
> 
> 
> _______________________________________________
> This is the CODE/400 Discussion & Support (CODE400-L) mailing list
> To post a message email: CODE400-L-Zwy7GipZuJhWk0Htik3J/[email protected]
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/code400-l
> or email: CODE400-L-request-Zwy7GipZuJhWk0Htik3J/[email protected]
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/code400-l.
> 
> NOTE: WDSc for iSeries disucssion has it's own mailing list.
> Information can be found at
> http://lists.midrange.com/cgi-bin/listinfo/wdsc-l
_______________________________________________
This is the CODE/400 Discussion & Support (CODE400-L) mailing list
To post a message email: CODE400-L-Zwy7GipZuJhWk0Htik3J/[email protected]
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/code400-l
or email: CODE400-L-request-Zwy7GipZuJhWk0Htik3J/[email protected]
Before posting, please take a moment to review the archives
at http://archive.midrange.com/code400-l.

NOTE: WDSc for iSeries disucssion has it's own mailing list.
Information can be found at http://lists.midrange.com/cgi-bin/listinfo/wdsc-l