Re: LCDproc - LCD2USB - Openbsd 4.9

De : [email protected]
[mailto:[email protected]] De la part de Yannick Lebreton
Envoyé : samedi 24 septembre 2011 01:00
À : 'Markus Dolze'; [email protected]
Objet : Re: [Lcdproc] LCDproc - LCD2USB - Openbsd 4.9

>Hi Markus and Jannis,

>With --disable--ethlcd    there's progress. Only One error  :

>LCDd:/usr/local/lib/lcdproc/hd44780.so: undefined symbol 'common_init'

>Could not open driver module /usr/local/lib/lcdproc/hd44780.so: Cannot load
>specified object Driver [hd44780] binding failed Could not load driver
hd44780 There >is no output driver Critical error while initializing, abort.

>My compil log in attachment .

>thank you for your answer. A little more help please ! 

>Yannick 



Anyone for help me again ? 

What's the nam of the device DEV=/dev/...   I can use with 

Controller /dev/usb3:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
NVIDIA(0x10de), rev 1.00
  uhub3
 port 1 powered
 port 2 powered
 port 3 powered
 port 4 addr 2: low speed, power 80 mA, config 1, LCD2USB(0xc630), Lcdmod
Kit(0x0403), rev 1.01
   ugen1
 port 5 powered
 port 6 powered


/dev/ugen1 or /dev/ugen1.04 ? 

Thx for your help 


-----Message d'origine-----
De : [email protected]
[mailto:[email protected]] De la part de Markus Dolze
Envoyé : vendredi 23 septembre 2011 20:29 À : [email protected]
Objet : Re: [Lcdproc] LCDproc - LCD2USB - Openbsd 4.9

On 18.09.2011 23:41, Yannick Lebreton wrote:
>
> Hi all,
>
>  
>
> I am trying to use LCDproc 0.5.4 on Openbsd 4.9 (i386 or amd64)  in 
> order to use my LCD2USB controller
>
>  
>
> Compilation works by when I start LCDd I get following messages:
>
>  
>
> # LCDd
>
> LCDd:/usr/local/lib/lcdproc/hd44780.so: undefined symbol 'sock_send'
>
> LCDd:/usr/local/lib/lcdproc/hd44780.so: undefined symbol 'sock_connect'
>
> LCDd:/usr/local/lib/lcdproc/hd44780.so: undefined symbol 'sock_close'
>
> LCDd:/usr/local/lib/lcdproc/hd44780.so: undefined symbol 'common_init'
>
> LCDd:/usr/local/lib/lcdproc/hd44780.so: undefined symbol 'sock_recv'
>
> Could not open driver module /usr/local/lib/lcdproc/hd44780.so: Cannot 
> load specified object
>
> Driver [hd44780] binding failed
>
> Could not load driver hd44780
>
> There is no output driver
>
> Critical error while initializing, abort.
>
>  
>
>  
>
>

Unfortunately I am not aware of anyone working with LCDproc on OpenBSD and
don't have the time to check on my own.

The error may be caused by the ethlcd connection type which uses these
functions, therefore you may try to run

'configure --disable-ethlcd'

Regards,
Markus

_______________________________________________
LCDproc mailing list
[email protected]
http://lists.omnipotent.net/mailman/listinfo/lcdproc