Re: [ITM] Reconfiguring KSY and TEPS w/o the GUI

For the TEMS updating the .config file is fine for temporary changes, but 
long term very bad since it will be over-written by a TEMS 
reconfiguration.

After ITM 623 create a file with same attributes/owner/group 

xx.environment 

and place any permanent overrides in that file. That is guaranteed to be 
preserved through future changes.

The only one I could not change that way was KBB_RAS1_LOG. That has to be 
in xx.ini and [for TEMS] a ./itmcmd config  operation.

Regards, 
______________________________________________


John Alvord
Advisory Engineer
IBM Tivoli Monitoring 6 Platform
Customer Support 
Office: 1-720-396-2788 
Mobile: none 
jalvord-r/[email protected]

Cloud & Smarter Infrastructure
IBM Support Portal
Open a New Service Request
Update your PMR via Email
Escalate your PMR
My Blog: Wonderful World of Situations
Secure upload to ECUREP







From:   Brett Yamazi/Austin/IBM@IBMUS
To:     "Discussion list for Tivoli product and Tivoli Ready products." 
<[email protected]>, 
Date:   07/12/2013 12:09 PM
Subject:        Re: [TME10] [ITM] Reconfiguring KSY and TEPS w/o the GUI
Sent by:        [email protected]



At ITM 6.2.3 FP1, you can reconfigure all those components via the "itmcmd 
config -A <productCode>" CLI.  The sy / hd / pa configuration will allow 
you to specify the JAR file path(s).  One thing I remember is that if you 
need to specify more than one JAR file, it uses comma-separated entries 
for sy and hd, but colon-separated entries for pa.  Oracle probably only 
needs one JAR file to be specified so you'll be ok, but anyone else doing 
this will need to remember for a different Warehouse RDBMS like DB2 which 
uses two JARs.

Also when editing config files, you usually don't want to edit the 
*.config file because it's the file that gets re-written each time the 
Agent starts (the exception would a TEMS).  If you ever need to edit 
anything in the config manually without using the CLI / MTEMS, then make a 
backup copy of the <productCode>.ini file first, and then edit the 
<productCode>.ini file.  The <productCode>.ini  file gets merged with 
settings in the <InstallDirectory>/config/.ConfigData/<productCode>env 
file to generate the new <productCode>.config file each time it starts.

______________________________________________ 


Brett Yamazi
Senior Software Engineer
IBM Software / Cloud and Smarter Infrastructure
Customer Support
Ph: 1.512.286.3629
byamazi-r/[email protected]

Cloud & Smarter Infrastructure
IBM Support Portal
Open a New Service Request
Update your PMR via Email 





"Howell, Joseph" ---07/12/2013 01:46:00 PM---ITM 6.2.3 fp1 on AIX. I need 
to upgrade my Oracle warehouse DB, and the path to the JDBC drivers wil

From: "Howell, Joseph" <[email protected]>
To: "[email protected]" <[email protected]>, 
Date: 07/12/2013 01:46 PM
Subject: [TME10] [ITM] Reconfiguring KSY and TEPS w/o the GUI
Sent by: [email protected]



ITM 6.2.3 fp1 on AIX. 
 
I need to upgrade my Oracle warehouse DB, and the path to the JDBC drivers 
will change.  I?ll need to reconfigure TEPS, KSY, KHD, and PA but I don?t 
have access to a GUI (yet) to run MTEMS for TEPS and PA.  Couldn?t I just 
edit cq.config and pa.config, update Kxx_WAREHOUSE_JARS manually, and run 
the itmcmd config command for each instead?
 
  


JOSEPH HOWELL
SYSTEMS ENGINEER
345 Court Street  l  Coraopolis, PA  15108
[email protected]  l  o: 724.273.4182
 

 
  

The information contained in this message and any attachments 
(collectively, the "Transmission") from Dick's Sporting Goods, Inc. or one 
of its subsidiaries contains confidential information and is intended 
solely for the named recipient(s). If you are not a named recipient, you 
are prohibited from copying, distributing or using this Transmission. 
Please contact the sender immediately by returning the e-mail and deleting 
the original Transmission. _______________________________________________
TME10 mailing list
[email protected]
Unsubscribe:[email protected]_______________________________________________
TME10 mailing list
[email protected]
Unsubscribe:[email protected]

_______________________________________________
TME10 mailing list
[email protected]
Unsubscribe:[email protected]