SV: Chrony 4.2 Ubuntu 22.04 IPv6 not sending request
Henning Svane <hsv-i2u8QauLV39aa/[email protected]>
| Newsgroups | gmane.comp.time.chrony.user |
|---|---|
| Message-ID | <5ABC601D16A6044981773D154D5C9F7102F4AB0974@XMail-DAG1.energy.local> |
Hi chronyc -n sources -a MS Name/IP address Stratum Poll Reach LastRx Last sample =============================================================================== ^? ####:####:####:4020::11 0 4 0 - +0ns[ +0ns] +/- 0ns ^? ####:####:####:4020::12 0 4 0 - +0ns[ +0ns] +/- 0ns ^? ####:####:####:4020::13 0 4 0 - +0ns[ +0ns] +/- 0ns ^? ####:####:####:4020::14 0 4 0 - +0ns[ +0ns] +/- 0ns Output the 4 IPv6 addresses correct If "chronyc -n sources -a" do it mean that the IPv6 numbers has been understand correct from the config file? And sudo chronyc ntpdata Printet all zeros all way down. Here for the first NTP Server. And I can see the addresses are both zeros? Remote address : [UNSPEC] (00000000) Remote port : 0 Local address : [UNSPEC] (00000000) Leap status : Normal Version : 0 Mode : Invalid Stratum : 0 Poll interval : 0 (1 seconds) Precision : 0 (1.000000000 seconds) Root delay : 0.000000 seconds Root dispersion : 0.000000 seconds Reference ID : 00000000 () Reference time : Thu Jan 01 00:00:00 1970 Offset : +0.000000000 seconds Peer delay : 0.000000000 seconds Peer dispersion : 0.000000000 seconds Response time : 0.000000000 seconds Jitter asymmetry: +0.00 NTP tests : 000 000 0000 Interleaved : No Authenticated : No TX timestamping : Invalid RX timestamping : Invalid Total TX : 0 Total RX : 0 Total valid RX : 0 Regards Henning -----Oprindelig meddelelse----- Fra: Miroslav Lichvar <[email protected]> Sendt: 23. juni 2022 14:20 Til: [email protected] Emne: Re: [chrony-users] Chrony 4.2 Ubuntu 22.04 IPv6 not sending request On Thu, Jun 23, 2022 at 12:15:39PM +0000, Henning Svane wrote: > Hi > > Are there anything special I have to do to get the client to send IPv6 request to the NTP Server? No, IPv6 should work equally well as IPv4. > > IPv4 works, but not IPv6 > I have modify the config file to only have IPv6 server addresses and with tcpdump I can see no request has been send after 5 min. > > With IPv4 addresses it works fine. > > I have moved the config file from 20.04 chrony 3.5 where it works, to 22.04 and now IPv6 do not work??? Does "chronyc -n sources -a" print the server address? What does "chronyc ntpdata" print? -- Miroslav Lichvar -- To unsubscribe email chrony-users-request-kWFZVVI9zxvPqho9SqqRMmD2FQJk+8+b@public.gmane.org with "unsubscribe" in the subject. For help email chrony-users-request-kWFZVVI9zxvPqho9SqqRMmD2FQJk+8+b@public.gmane.org with "help" in the subject. Trouble? Email [email protected] -- To unsubscribe email chrony-users-request-kWFZVVI9zxvPqho9SqqRMmD2FQJk+8+b@public.gmane.org with "unsubscribe" in the subject. For help email chrony-users-request-kWFZVVI9zxvPqho9SqqRMmD2FQJk+8+b@public.gmane.org with "help" in the subject. Trouble? Email [email protected]