Re: System Clock is updated before the TAI-UTC offset is applied for PHC source in chrony 6.4.1

Why use the PHC =E2=80=9C=20

chronyc tracking
Reference ID    : 50484330 (PHC0)
Stratum         : 1
Ref time (UTC)  : Fri Jan 16 08:40:40 2026
System time     : 0.000000007 seconds fast of NTP time
Last offset     : -0.000000014 seconds
RMS offset      : 0.000000029 seconds
Frequency       : 14.710 ppm slow
Residual freq   : +0.000 ppm
Skew            : 0.017 ppm
Root delay      : 0.000000001 seconds
Root dispersion : 0.000000544 seconds
Update interval : 1.0 seconds
Leap status     : Normal


Because why not=E2=80=A6.=20
Also I am playing with PTP so it just is what it is and I need the =
accuracy.

But look at that system time=E2=80=A6. It=E2=80=99s in the nanoseconds =
of accuracy - just because - why not have the best if you can get the =
best.=20


> On 16 Jan 2026, at 19:56, Bill Unruh <[email protected]> wrote:
>=20
> Although this is certainly a pain, I wonder why you are using the PHC =
source
> at all. Use a couple of network sources plus the gps (yes, gps under =
chrony
> can get down to sub-micro second accuracy so it would always be the =
primary
> source, except if it loast tracking, in which case the fallback would =
be the
> time from the network source, which would be in the microseconds, or =
10s of
> microseconds accuracy.
> What accuracy do you need? I know that 1 second in the life of the =
universe
> would give nice bragging rights, but do you really need that? (and no =
gps
> would not give that).
>=20
> Also, on startup the clock should be assumed to be bad for some time. =
Why are
> you switching it off at all?If you want accurate time, let the clock =
and
> chrony run for as long as possible.
>=20
> William G. Unruh __|__Hagler Fellow, Distinguished |_Tel:UBC =
+1(604)822-3273
> Physics&Astronomy _|__ Research Prof, IQSE         |__  US =
+1(979)7399950
> UBC, Vancouver,BC _|_ TAMU4242, 578 University Dr  |_ =
[email protected]
> Canada V6T 1Z1 ____|__College Stn, Tx, USA 77843  =
_|_www.theory.physics.ubc.ca
> I cannot reply to emails from outlook or hotmail or other microsoft =
domains.
>=20
> On Fri, 16 Jan 2026, Simon Plackett wrote:
>=20
>> [CAUTION: Non-UBC Email]
>>=20
>> Hi,
>>=20
>> Before I send a lot of detail I wondered if anyone had seen this
>> phenomenon. I have just upgraded my local chrony server to Trixie on
>> RPI 5 with chrony 4.6.1.
>>=20
>> I had previously been using the ethernet NIC clock as a time source
>> with ptp4l and phc2sys, which worked fine.
>>=20
>> During the upgrade I changed to leapseclist from leapsectz as the
>> latter does not work on Trixie.
>>=20
>> The issue is that on startup the system clock is set by the PHC =
source
>> before the TAI-UTC adjustment has been applied which means it jumps
>> 36+ seconds one way and then back again during the startup. This
>> obviously trashes the PHC as a source, and it didn't happen
>> previously.
>>=20
>> Essentially PHC is chosen as the source, updates system clock (wrong
>> by ~37s) then the TAI-UTC adjustment is found which causes system =
time
>> to jump again in the opposite direction by ~37s
>>=20
>> I can see this using systemctl status chrony or using journalctl.
>>=20
>> I have currently turned PHC off again - but happy to turn back on and
>> send any logs etc that might be useful.
>>=20
>> The other source is PPS from GPS, which is even more accurate on the
>> new versions :-)
>>=20
>> Thanks
>> Simon
>>=20
>> --=20
>> To unsubscribe email chrony-users-request-kWFZVVI9zxvPqho9SqqRMmD2FQJk+8+b@public.gmane.org
>> with "unsubscribe" in the subject.
>> For help email chrony-users-request-kWFZVVI9zxvPqho9SqqRMmD2FQJk+8+b@public.gmane.org
>> with "help" in the subject.
>> Trouble?  Email [email protected]
>>=20
>>=20
>=20
> --=20
> To unsubscribe email chrony-users-request-kWFZVVI9zxvPqho9SqqRMmD2FQJk+8+b@public.gmane.org with =
"unsubscribe" in the subject.
> For help email chrony-users-request-kWFZVVI9zxvPqho9SqqRMmD2FQJk+8+b@public.gmane.org with "help" =
in the subject.
> Trouble?  Email [email protected]
>=20


-- 
To unsubscribe email chrony-users-request-kWFZVVI9zxvPqho9SqqRMmD2FQJk+8+b@public.gmane.org 
with "unsubscribe" in the subject.
For help email chrony-users-request-kWFZVVI9zxvPqho9SqqRMmD2FQJk+8+b@public.gmane.org 
with "help" in the subject.
Trouble?  Email [email protected]