Re: application runs at slower rate in mesa 9.0.1 compare to mesa 7.8

Actually glxinfo was also not working (I am checking on that know)
Pls refer attached mail.

Best Regards,
Anil V

-----Original Message-----
From: Brian Paul [mailto:[email protected]] 
Sent: Tuesday, February 04, 2014 10:18 PM
To: Anil Valmiki (RBEI/ECF3); [email protected]
Subject: Re: [Mesa-users] application runs at slower rate in mesa 9.0.1 compare to mesa 7.8

On 02/03/2014 10:00 PM, Anil Valmiki (RBEI/ECF3) wrote:
> Dear Brian,
>
>>> Which driver are you using?
>        Gallium

Which gallium driver? :)  The output of glxinfo would be helpful.

-Brian


>>> Did you compile yourself?
>       Yes
>
>>> With the same options?
>
> DRIDRIVERS = "swrast"
> EGL_PLATFORMS  = "x11"
> EGL_PLATFORMS .= ",drm"
>
> EXTRA_OECONF += "--enable-gallium --with-gallium-drivers="nouveau,r600,svga,swrast""
> EXTRA_OECONF += "--enable-dri --with-dri-drivers=${DRIDRIVERS}"
> EXTRA_OECONF += "--enable-gbm"
>
> EXTRA_OECONF += "--enable-gles1 --enable-gles2 --enable-openvg --enable-gallium-egl --enable-gallium-gbm --enable-glx"
>
> EXTRA_OECONF += "--enable-egl --with-egl-platforms=${EGL_PLATFORMS}"
>
> X11_DEPS = "xf86driproto glproto virtual/libx11 libxext libxxf86vm libxdamage libxfixes"
> EXTRA_OECONF += "--enable-glx-tls"
> DEPENDS += "${X11_DEPS}"
>
>
> Previously I am using MESA 7.8
> Which is having a bug when you scissor a portion to write, it scissors in x mirror position and allowing us to write in x mirror position not in the scissor position .
> And also mesa 7.8 is old one which didn't support FBO .
> So I thought of upgrade to mesa 9.0.1 where I found that FPS(frame per second ) reduced by 50% while running opengles1.0 demo .
>
> Thanks in advance.
>
> Best Regards,
> Anil V
>
>
> -----Original Message-----
> From: [email protected] [mailto:[email protected]] On Behalf Of Brian Paul
> Sent: Friday, January 31, 2014 9:30 PM
> To: [email protected]
> Subject: Re: [Mesa-users] application runs at slower rate in mesa 9.0.1 compare to mesa 7.8
>
> On 01/21/2014 04:24 AM, Anil Valmiki (RBEI/ECF3) wrote:
>> Hi Everyone,
>> Is there any difference in rendering (like software or hardware) by
>> default from mesa 7.8 to mesa 9.0.1.
>> Because when I port to mesa 9.0.1 the application runs slower rate
>> compare to mesa 7.8.
>
> Impossible to say much without knowing more.  Which driver are you
> using?  Did you compile yourself?  With the same options?  Do you have a
> test program?
>
> -Brian
>
>
> _______________________________________________
> mesa-users mailing list
> [email protected]
> https://urldefense.proofpoint.com/v1/url?u=http://lists.freedesktop.org/mailman/listinfo/mesa-users&k=oIvRg1%2BdGAgOoM1BIlLLqw%3D%3D%0A&r=lGQMzzTgII0I7jefp2FHq7WtZ%2BTLs8wadB%2BiIj9xpBY%3D%0A&m=9NFfMcuhfDsCOJKxxwvUFptIvg0BHvi8mXcOJVv18Rk%3D%0A&s=8f230065ccda4b3eac0f616f26708d98364a3b709dccf9638e38fab51cba72e6
>

_______________________________________________
mesa-users mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/mesa-users