[PATCH 1/3] soc-camera: tw9910: modify V/H outpit pin setting to use VALID

tw9910 driver assume that V/H data is active high.
This is controlled by OUTCTR1 register.
When we use VALID data with active high,
the setting will be VSP_LO/HSP_LO.
This setting is correct,
because this register setting is based on SYNC.

Signed-off-by: Kuninori Morimoto <[email protected]>
---
 drivers/media/video/tw9910.c |   41 +++++++++++++----------------------------
 1 files changed, 13 insertions(+), 28 deletions(-)

diff --git a/drivers/media/video/tw9910.c b/drivers/media/video/tw9910.c
index 6d8dede..426f6fc 100644
--- a/drivers/media/video/tw9910.c
+++ b/drivers/media/video/tw9910.c
@@ -166,7 +166,7 @@
 #define VSSL_FIELD  0x20 /*   2 : FIELD  */
 #define VSSL_VVALID 0x30 /*   3 : VVALID */
 #define VSSL_ZERO   0x70 /*   7 : 0      */
-#define HSP_LOW     0x00 /* 0 : HS pin output polarity is active low */
+#define HSP_LO      0x00 /* 0 : HS pin output polarity is active low */
 #define HSP_HI      0x08 /* 1 : HS pin output polarity is active high.*/
 			 /* HS pin output control */
 #define HSSL_HACT   0x00 /*   0 : HACT   */
@@ -239,18 +239,6 @@ struct tw9910_priv {
 	u32                             revision;
 };
 
-/*
- * register settings
- */
-
-#define ENDMARKER { 0xff, 0xff }
-
-static const struct regval_list tw9910_default_regs[] =
-{
-	{ OUTCTR1, VSP_LO | VSSL_VVALID | HSP_HI | HSSL_HSYNC },
-	ENDMARKER,
-};
-
 static const enum v4l2_imgbus_pixelcode tw9910_color_codes[] = {
 	V4L2_IMGBUS_FMT_VYUY,
 };
@@ -463,20 +451,6 @@ static int tw9910_set_hsync(struct i2c_client *client,
 	return ret;
 }
 
-static int tw9910_write_array(struct i2c_client *client,
-			      const struct regval_list *vals)
-{
-	while (vals->reg_num != 0xff) {
-		int ret = i2c_smbus_write_byte_data(client,
-						    vals->reg_num,
-						    vals->value);
-		if (ret < 0)
-			return ret;
-		vals++;
-	}
-	return 0;
-}
-
 static void tw9910_reset(struct i2c_client *client)
 {
 	tw9910_mask_set(client, ACNTL1, SRESET, SRESET);
@@ -681,7 +655,18 @@ static int tw9910_s_crop(struct v4l2_subdev *sd, struct v4l2_crop *a)
 	 * reset hardware
 	 */
 	tw9910_reset(client);
-	ret = tw9910_write_array(client, tw9910_default_regs);
+
+	/*
+	 * set OUTCTR1
+	 *
+	 * tw9910 use valid data on active high.
+	 * Then, VSP/HSP low seems strange here. But this is correct.
+	 * Because it is based on SYNC.
+	 * So, VSP/HSP low mean active high for valid data
+	 */
+	ret = i2c_smbus_write_byte_data(client, OUTCTR1,
+					VSP_LO | VSSL_VVALID |
+					HSP_LO | HSSL_DVALID);
 	if (ret < 0)
 		goto tw9910_set_fmt_error;
 
-- 
1.6.3.3

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list