Re: rtpengine module does not detect new nodes in table

Thank you everyone for those suggestions.


On Tue, 29 Apr 2025 at 01:34, Ben Kaufman <[email protected]> wrote:

> It's possible to add a http listener to Kamailio and use rpc over http.
>
> You can also use rtimer and add a route to reload the table periodically.
>
> Regards,
> Kaufman
>
>
>
> ------------------------------
> *From:* David Cunningham
> *Sent:* Sunday, April 27, 2025 7:14 PM
> *To:* Ben Kaufman
> *Cc:* Kamailio (SER) - Users Mailing List
> *Subject:* Re: [SR-Users] rtpengine module does not detect new nodes in
> table
>
> *CAUTION:* This email originated from outside the organization. *Do not
> click links or open attachments* unless you recognize the sender and know
> the content is safe.
>
> Hello,
>
> Thank you for that. In our case the database entries are inserted on a
> separate server to the one Kamailio is running on, so it's not easy for the
> program adding nodes to run "kamcmd rtpengine.reload".
>
> Is this the only solution that's available?
>
>
> On Thu, 24 Apr 2025 at 13:47, Ben Kaufman <[email protected]> wrote:
>
> There's an RPC command for reloading rtpengine config:
>
>
> https://www.kamailio.org/docs/modules/stable/modules/rtpengine.html#rtpengine.r.reload
> <https://urldefense.com/v3/__https://www.kamailio.org/docs/modules/stable/modules/rtpengine.html*rtpengine.r.reload__;Iw!!KWzduNI!Zg9I9J9aWZOkY7EORpWUetminDhbl4eQzmJCHHG69gkHLYX7XXCuxzUTQABgiLpxieevA-sZYYWqyDfucIjavT8$>
>
> Regards,
> Kaufman
>
> ------------------------------
> *From:* David Cunningham via sr-users
> *Sent:* Wednesday, April 23, 2025 4:55 PM
> *To:* Kamailio (SER) - Users Mailing List
> *Cc:* David Cunningham
> *Subject:* [SR-Users] rtpengine module does not detect new nodes in table
>
> *CAUTION:* This email originated from outside the organization. *Do not
> click links or open attachments* unless you recognize the sender and know
> the content is safe.
>
> Hello,
>
> We are using Kamailio 5.8.2 with the rtpengine module on Ubuntu 22.04. The
> "rtpengine" table is used to define nodes, with a configuration like this:
>
>     modparam( "rtpengine", "db_url", DB_URL )
>     modparam( "rtpengine", "table_name", "rtpengine" )
>     modparam( "rtpengine", "setid_default", 1 )
>
> It works fine if Kamailio is restarted after entries in the "rtpengine"
> table are inserted or deleted, but new entries in the table aren't detected
> automatically. Is there a way to configure Kamailio to detect them?
>
> Thank you,
>
> --
> David Cunningham, Voisonics Limited
> http://voisonics.com/
> <https://urldefense.com/v3/__http://voisonics.com/__;!!KWzduNI!ZdLfAmCE7Q_j-nlwkepzScbqd2y5y4MYuTtXwBhV-Hd-NoiLTmYB-0XaOErxWJh78fmsFHNDJvVclyTn9-JJljo$>
> USA: +1 213 221 1092
> New Zealand: +64 (0)28 2558 3782
>
>
>
> --
> David Cunningham, Voisonics Limited
> http://voisonics.com/
> <https://urldefense.com/v3/__http://voisonics.com/__;!!KWzduNI!Zg9I9J9aWZOkY7EORpWUetminDhbl4eQzmJCHHG69gkHLYX7XXCuxzUTQABgiLpxieevA-sZYYWqyDfuwP5wkYY$>
> USA: +1 213 221 1092
> New Zealand: +64 (0)28 2558 3782
>


-- 
David Cunningham, Voisonics Limited
http://voisonics.com/
USA: +1 213 221 1092
New Zealand: +64 (0)28 2558 3782

__________________________________________________________
Kamailio - Users Mailing List - Non Commercial Discussions -- [email protected]
To unsubscribe send an email to [email protected]
Important: keep the mailing list in the recipients, do not reply only to the sender!