Re: [EXTERNAL] Re: RTPEngine installation on RHEL 8.x or Rocky Linux 8.x

Use the LTS branch mr12.5. It has the required PIE flags included.

Cheers


On 15/09/2025 11.43, Chandramouli P via sr-users wrote:
> Hello Sergy,
>
> Good morning and thank you for your reply. Somehow, I wasn't able to 
> login to my pastebin account. Please find the error that I am getting 
> in the attached file. Thank you.
>
> Best regards,
> Chandramouli.
>
> On Mon, Sep 15, 2025 at 5:43 PM Sergei Safarov <[email protected]> 
> wrote:
>
>     Pastebin is no available more.
>     Please post again.
>
>     On Sat, 2025-09-13 at 13:43 +0530, Chandramouli P wrote:
>>     Hello Sergey,
>>
>>     Good morning and thank you for your reply. As you suggested, I
>>     tried to compile the mr12.4 version and getting the below error:
>>
>>     *https://pastebin.com/fc54vv9T*
>>
>>     Please advise me to move forward and thank you in advance.
>>
>>     Best Regards,
>>     Chandramouli.
>>
>>
>>
>>
>>
>>     On Fri, Sep 12, 2025 at 11:15 PM Sergey Safarov
>>     <[email protected]> wrote:
>>>     Looks like you're trying to build the master branch
>>>     I use https://github.com/sipwise/rtpengine/commits/mr12.4 branch
>>>     on CentOS 8
>>>     Probably this should also work for Rocky 8
>>>     After you compile this branch, you can build for a more recent
>>>     branch.
>>>
>>>
>>>     On Fri, Sep 12, 2025 at 5:11 PM Chandramouli P via sr-users
>>>     <[email protected]> wrote:
>>>>     Hello Alex,
>>>>
>>>>     Good morning and thank you for your reply. As you suggested, I
>>>>     followed and tried to install RTPEngine on Rocky Linux 8.x.
>>>>     But, I'm still getting errors.
>>>>
>>>>     Please find the installation steps that I followed here:
>>>>     *https://pastebin.com/wi4YtbKZ*
>>>>
>>>>     Please find the complete error description here:
>>>>     *https://pastebin.com/LbgYQMGb*
>>>>
>>>>     Please advise me to move forward and thank you in advance.
>>>>
>>>>     Best Regards,
>>>>     Chandramouli.
>>>>
>>>>
>>>>
>>>>     On Wed, Sep 10, 2025 at 8:04 PM Alex Balashov
>>>>     <[email protected]> wrote:
>>>>>     It would be hard to share a step-by-step guide as I don't have
>>>>>     one handy and it would be labourious to set up a fresh host
>>>>>     for the express purpose of writing one for you, but I do this
>>>>>     routinely on EL8 and Rocky 8, and have done so dozens of times.
>>>>>
>>>>>     Tips:
>>>>>
>>>>>     - You will need EPEL.
>>>>>
>>>>>     - You will need the CBR repository or whatever has replaced
>>>>>     PowerTools in Rocky 8.
>>>>>
>>>>>     Otherwise, it's just installing the dependencies until you get
>>>>>     there.
>>>>>
>>>>>     -- Alex
>>>>>
>>>>>     > On Sep 10, 2025, at 10:07 AM, Chandramouli P via sr-users
>>>>>     <[email protected]> wrote:
>>>>>     >
>>>>>     > Hello,
>>>>>     >
>>>>>     > I tried a lot to install RTPEngine on RHEL 8.x and as well
>>>>>     as in Rocky Linux 8.x also using different sources. But, I am
>>>>>     facing a lot of issues like libraries issues, dependencies
>>>>>     issues, conflict issues etc.  Anyone successfully installed
>>>>>     RTPEngine on RHEL 8.x or Rocky Linux 8.x (Not on CentOS)? If
>>>>>     so, could you please share the documentation step-by-step or
>>>>>     web URL? Thanks in advance.
>>>>>     >
>>>>>     > Best regards,
>>>>>     > Chandramouli.
>>>>>     > __________________________________________________________
>>>>>     > Kamailio - Users Mailing List - Non Commercial Discussions
>>>>>     -- [email protected]
>>>>>     > To unsubscribe send an email to
>>>>>     [email protected]
>>>>>     > Important: keep the mailing list in the recipients, do not
>>>>>     reply only to the sender!
>>>>>
>>>>>     --
>>>>>     Alex Balashov
>>>>>     Principal Consultant
>>>>>     Evariste Systems LLC
>>>>>     Web: https://evaristesys.com, https://www.csrpswitch.com
>>>>>     Tel: +1-706-510-6800
>>>>>
>>>>     __________________________________________________________
>>>>     Kamailio - Users Mailing List - Non Commercial Discussions --
>>>>     [email protected]
>>>>     To unsubscribe send an email to [email protected]
>>>>     Important: keep the mailing list in the recipients, do not
>>>>     reply only to the sender!
>
>
> __________________________________________________________
> Kamailio - Users Mailing List - Non Commercial Discussions [email protected]
> To unsubscribe send an email [email protected]
> Important: keep the mailing list in the recipients, do not reply only to the sender!

__________________________________________________________
Kamailio - Users Mailing List - Non Commercial Discussions -- [email protected]
To unsubscribe send an email to [email protected]
Important: keep the mailing list in the recipients, do not reply only to the sender!