[webmin-l] Fwd: Changing service status "start at boot" not working

Ok, this is what I've seen so far. Fresh installation of Debian 8.4, Webmin
1.801 and virtualmin 5.03:

- mysql, apache, postfix, proftpd, cron service: can disable/enable
correctly
- spamassasin, dovecot, bind9: cannot change status.

Maybe this info is useless, but when installing Virtualmin, this appeared
in the output:

insserv: warning: current start runlevel(s) (empty) of script `mailman'
overrides LSB defaults (2 3 4 5).
insserv: warning: current stop runlevel(s) (2 3 4 5) of script `mailman'
overrides LSB defaults (empty).
update-rc.d: error: cannot find a LSB script for postgresql-8.3
Failed to stop postgresql-8.3.service: Unit postgresql-8.3.service not
loaded.
update-rc.d: error: cannot find a LSB script for postgresql-8.4
Failed to stop postgresql-8.4.service: Unit postgresql-8.4.service not
loaded.
insserv: warning: current start runlevel(s) (empty) of script
`spamassassin' overrides LSB defaults (2 3 4 5).
insserv: warning: current stop runlevel(s) (0 1 2 3 4 5 6) of script
`spamassassin' overrides LSB defaults (0 1 6).
insserv: warning: current start runlevel(s) (empty) of script
`clamav-daemon' overrides LSB defaults (2 3 4 5).
insserv: warning: current stop runlevel(s) (0 1 2 3 4 5 6) of script
`clamav-daemon' overrides LSB defaults (0 1 6).

Jamie, if you would like to test and view it in my server, I can give you
access if you wish.

Regards.

---------- Forwarded message ----------
From: Alfredo Alcaide <[email protected]>
Date: 2016-06-03 12:39 GMT+02:00
Subject: Re: [webmin-l] Changing service status "start at boot" not working
To: [email protected]


Sorry for the delay in my answer, but I've made a couple of tests more to
try to find any hint on what's happening.

The installation was made using a minimum precompiled image from the
hosting company (OVH), but I didn't find any special configuration that
could make me think that any change was made that could affect the normal
configuration.

Answering your question, Webmin says "Boot system : Systemd".

I also tested in a CentOS machine (version 7.2.1511, Webmin version 1.801,
no Virtualmin installed), with Boot system as Systemd. Disabling/enabling
services works correctly.

And... I've tested on a third server, also with Debian (same version),
Webmin (same version), but without Virtualmin. Surprise: it works correctly.

Now I'm lost. Just a few minutes ago I purchased another server. I'm going
to install Debian, plus Webmin+Virtualmin (all standard installation), and
I'll post the results of the tests.

Best regards.
Alfredo.

2016-06-03 3:28 GMT+02:00 Andrey Repin <[email protected]>:

> Greetings, Jamie Cameron!
>
> >> My system is a Debian 8.4, completly updated, with Webmin 1.801 +
> >> Virtualmin 5.03. No errors have been logged (and if they have, I don't
> know
> >> where to find them).
>
> > That seems like a bug. In the Bootup and Shutdown module, what boot
> system does
> > it say is in use at the top of the page? It should be something like
> "upstart" or
> > "systemd"
>
> If it is default install, then it should be systemd, IIRC.
> Though, it IS possible to revert to upstart, quite easily.
>
>
> --
> With best regards,
> Andrey Repin
> Friday, June 3, 2016 04:27:21
>
> Sorry for my terrible english...
>
>
>
> ------------------------------------------------------------------------------
> What NetFlow Analyzer can do for you? Monitors network bandwidth and
> traffic
> patterns at an interface-level. Reveals which users, apps, and protocols
> are
> consuming the most bandwidth. Provides multi-vendor support for NetFlow,
> J-Flow, sFlow and other flows. Make informed decisions using capacity
> planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e
> -
> Forwarded by the Webmin mailing list at
> [email protected]
> To remove yourself from this list, go to
> http://lists.sourceforge.net/lists/listinfo/webadmin-list
>

------------------------------------------------------------------------------
What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic
patterns at an interface-level. Reveals which users, apps, and protocols are 
consuming the most bandwidth. Provides multi-vendor support for NetFlow, 
J-Flow, sFlow and other flows. Make informed decisions using capacity 
planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e

-
Forwarded by the Webmin mailing list at [email protected]
To remove yourself from this list, go to
http://lists.sourceforge.net/lists/listinfo/webadmin-list