Re: [webmin-l] Fwd: Changing service status "start at boot" not working

Sounds like maybe Webmin is maybe mixing up init.d and upstart scripts. Remote access to your system to debug it would be quite useful ..  

On 03/Jun/2016 06:06 Alfredo Alcaide <[email protected]> wrote ..          Ok, this is what I've seen so far. Fresh installation of Debian 8.4, Webmin 1.801 and virtualmin 5.03: - mysql, apache, postfix, proftpd, cron service: can disable/enable correctly - spamassasin, dovecot, bind9: cannot change status.   Maybe this info is useless, but when installing Virtualmin, this appeared in the output:insserv: warning: current start runlevel(s) (empty) of script `mailman' overrides LSB defaults (2 3 4 5).insserv: warning: current stop runlevel(s) (2 3 4 5) of script `mailman' overrides LSB defaults (empty).update-rc.d: error: cannot find a LSB script for postgresql-8.3Failed to stop postgresql-8.3.service: Unit postgresql-8.3.service not loaded.update-rc.d: error: cannot find a LSB script for p
 ostgresql-8.4Failed to stop postgresql-8.4.service: Unit postgresql-8.4.service not loaded.insserv: warning: current start runlevel(s) (empty) of script `spamassassin' overrides LSB defaults
  (2 3 4 5).insserv: warning: current stop runlevel(s) (0 1 2 3 4 5 6) of script `spamassassin' overrides LSB defaults (0 1 6).insserv: warning: current start runlevel(s) (empty) of script `clamav-daemon' overrides LSB defaults (2 3 4 5).insserv: warning: current stop runlevel(s) (0 1 2 3 4 5 6) of script `clamav-daemon' overrides LSB defaults (0 1 6).Jamie, if you would like to test and view it in my server, I can give you access if you wish. Regards.   ---------- Forwarded message ----------From: Alfredo Alcaide <[email protected]>Date: 2016-06-03 12:39 GMT+02:00Subject: Re: [webmin-l] Changing service status "start at boot" not workingTo: [email protected]     Sorry for the delay in my answer, but I've made a couple of tests more to try to find any hint on what's happ
 ening.The installation was made using a minimum precompiled image from the hosting company (OVH), but I didn't find any special configuration that could make me think that any change was mad
 e that could affect the normal configuration.Answering your question, Webmin says "Boot system : Systemd". I also tested in a CentOS machine (version 7.2.1511, Webmin version 1.801, no Virtualmin installed), with Boot system as Systemd. Disabling/enabling services works correctly. And... I've tested on a third server, also with Debian (same version), Webmin (same version), but without Virtualmin. Surprise: it works correctly. Now I'm lost. Just a few minutes ago I purchased another server. I'm going to install Debian, plus Webmin+Virtualmin (all standard installation), and I'll post the results of the tests.     Best regards. Alfredo.     2016-06-03 3:28 GMT+02:00 Andrey Repin <[email protected]>: Greetings, Jamie Cameron!  >> My system is a Debian 8.4, completly updated, with Webmin 
 1.801 + >> Virtualmin 5.03. No errors have been logged (and if they have, I don't know >> where to find them).  > That seems like a bug. In the Bootup and Shutdown module, what boot system d
 oes > it say is in use at the top of the page? It should be something like "upstart" or > "systemd"  If it is default install, then it should be systemd, IIRC. Though, it IS possible to revert to upstart, quite easily.   -- With best regards, Andrey Repin Friday, June 3, 2016 04:27:21  Sorry for my terrible english...   ------------------------------------------------------------------------------ What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic patterns at an interface-level. Reveals which users, apps, and protocols are consuming the most bandwidth. Provides multi-vendor support for NetFlow, J-Flow, sFlow and other flows. Make informed decisions using capacity planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e - Forwarded by the Webmin 
 mailing list at [email protected] To remove yourself from this list, go to http://lists.sourceforge.net/lists/listinfo/webadmin-list

------------------------------------------------------------------------------
What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic
patterns at an interface-level. Reveals which users, apps, and protocols are 
consuming the most bandwidth. Provides multi-vendor support for NetFlow, 
J-Flow, sFlow and other flows. Make informed decisions using capacity 
planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e

-
Forwarded by the Webmin mailing list at [email protected]
To remove yourself from this list, go to
http://lists.sourceforge.net/lists/listinfo/webadmin-list