Re: [e-users] screen setup error
mh via enlightenment-users <[email protected]>
| Newsgroups | gmane.comp.window-managers.enlightenment.user |
|---|---|
| Message-ID | <[email protected]> |
On 4/6/23 00:51, Carsten Haitzler wrote: > On Wed, 5 Apr 2023 14:49:28 -0400 mh via enlightenment-users > <[email protected]> said: > >> On 4/5/23 12:43, Carsten Haitzler wrote: >>> On Tue, 4 Apr 2023 20:22:32 -0400 mh via enlightenment-users >>> <[email protected]> said: >>> >>>> I'm just back to using E after a while, using 0.25.4 from Debian sid. >>>> After first logging in, and every time after resuming from >>>> screensaver/blanking, I get the pop-up error message: "You seem to have >>>> no screens configured to be on the given outputs you have. This should >>>> be fixed by going to: Settings-Screen-Screen Setup." >>> is this a laptop? did you have the lid closed? >> it's a desktop, 4080 gpu, evil NVIDIA driver version 530.30.02 installed > this would imply the nvidia driver is unplugging all screens ever time the > screen goes into dpms. check your logs as per previous email and see. all lines > going RRR: will have to do with randr screen stuff. Not sure which log to check. I looked at Xorg.0.log but didn't see anything with RRR. I was going to uninstall the nvidia drivers and try it with nouveau but having problems with X starting. Not sure if nouveau supports rtx4080 yet. >>>> When I do that, there is a list showing two DP-4 outputs where the >>>> monitor is connected, and a third that lists the monitor. But the only >>>> one that I can set the screen setup settings for is the first DP-4. What >>>> do I need to do to setup the monitor to the output properly? >>> what? multiple DP-4's - that shouldnt happen. you should have all outputs >>> named differently. does xrandr (commandline) also list multiple dp-4's? >> only one DP-4 with xrandr. this is the output: >> >> $ xrandr >> Screen 0: minimum 8 x 8, current 3840 x 2160, maximum 32767 x 32767 >> HDMI-0 disconnected primary (normal left inverted right x axis y axis) >> DP-0 disconnected (normal left inverted right x axis y axis) >> DP-1 disconnected (normal left inverted right x axis y axis) >> DP-2 disconnected (normal left inverted right x axis y axis) >> DP-3 disconnected (normal left inverted right x axis y axis) >> DP-4 connected 3840x2160+0+0 (normal left inverted right x axis y axis) >> 708mm x 399mm >> 3840x2160 60.00*+ 144.00 120.00 119.88 59.94 50.00 29.97 >> 2560x1440 143.97 120.00 59.95 >> 1920x1080 143.85 119.88 60.00 59.94 >> 1680x1050 59.95 >> 1440x900 59.89 >> 1280x1024 75.02 60.02 >> 1280x960 60.00 >> 1280x720 119.88 60.00 59.94 50.00 >> 1152x864 75.00 >> 1024x768 75.03 70.07 60.00 >> 800x600 75.00 72.19 60.32 56.25 >> 720x576 50.00 >> 720x480 59.94 >> 640x480 75.00 72.81 59.94 59.93 >> DP-5 disconnected (normal left inverted right x axis y axis) > are you sure dp-4 is listed twice and it isn't just the hoversel showing the > selected one at the top in addition to the set of possible selections below? I see DP-4 listed twice, then 32UHD144. If I hover/click over the first DP-4 I see a DP-4, indented and selectable. But the second one remains after I select a resolution and hit apply. The 32UHD144 entry is never selectable. >> _______________________________________________ >> enlightenment-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/enlightenment-users _______________________________________________ enlightenment-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/enlightenment-users