CD DVD burning solution OT: Re: New file uploaded to AutoItList
"valery_vi" <[email protected]>
| Newsgroups | gmane.comp.windows.autoit.user |
|---|---|
| Message-ID | <[email protected]> |
Steve,
But I found very many command line options of cdrecord.exe (folder
cdrtools).
Try this command line:
cdrecord.exe - help
DOC:
Usage: CDRECORD [options] track1...trackn
Options:
-version print version information and exit
dev=target SCSI target to use as CD/DVD-Recorder
gracetime=# set the grace time before starting to write
to #.
timeout=# set the default SCSI command timeout to #.
debug=#,-d Set to # or increment misc debug level
kdebug=#,kd=# do Kernel debugging
-verbose,-v increment general verbose level by one
-Verbose,-V increment SCSI command transport verbose
level by one
-silent,-s do not print status of failed SCSI commands
driver=name user supplied driver name, use with extreme
care
driveropts=opt a comma separated list of driver specific
options
-setdropts set driver specific options and exit
-checkdrive check if a driver for the drive is present
-prcap print drive capabilities for MMC compliant
drives
-inq do an inquiry for the drive and exit
-scanbus scan the SCSI and IDE buses and exit
-reset reset the SCSI bus with the cdrecorder (if
possible)
-abort send an abort sequence to the drive (may
help if hung)
-overburn allow to write more than the official size
of a medium
-ignsize ignore the known size of a medium (may cause
problems)
-useinfo use *.inf files to overwrite audio options.
speed=# set speed of drive
blank=type blank a CD-RW disc (see blank=help)
format format a CD-RW/DVD-RW/DVD+RW disc
formattype=# select the format method for DVD+RW disc
fs=# Set fifo size to # (0 to disable, default is
4 MB)
ts=# set maximum transfer size for a single SCSI
command
-load load the disk and exit (works only with tray
loader)
-lock load and lock the disk and exit (works only
with tray lo
ader)
-eject eject the disk after doing the work
-dummy do everything with laser turned off
-msinfo retrieve multi-session info for mkisofs >=
1.10
-toc retrieve and print TOC/PMA data
-atip retrieve and print ATIP data
-multi generate a TOC that allows multi session
In this case default track type is CD-ROM XA
mode 2 form
1 - 2048 bytes
-fix fixate a corrupt or unfixated disk (generate
a TOC)
-nofix do not fixate disk after writing tracks
-waiti wait until input is available before opening
SCSI
-immed Try to use the SCSI IMMED flag with certain
long lasting
commands
-force force to continue on some errors to allow
blanking bad d
isks
-tao Write disk in TAO mode. This option will be
replaced in
the future.
-dao Write disk in SAO mode. This option will be
replaced in
the future.
-sao Write disk in SAO mode. This option will be
replaced in
the future.
-raw Write disk in RAW mode. This option will be
replaced in
the future.
-raw96r Write disk in RAW/RAW96R mode. This option
will be repla
ced in the future.
-raw96p Write disk in RAW/RAW96P mode. This option
will be repla
ced in the future.
-raw16 Write disk in RAW/RAW16 mode. This option
will be replac
ed in the future.
-clone Write disk in clone write mode.
tsize=# Length of valid data in next track
padsize=# Amount of padding for next track
pregap=# Amount of pre-gap sectors before next track
defpregap=# Amount of pre-gap sectors for all but track
#1
mcn=text Set the media catalog number for this CD
to 'text'
isrc=text Set the ISRC number for the next track
to 'text'
index=list Set the index list for the next track
to 'list'
-text Write CD-Text from information from *.inf or
*.cue files
textfile=name Set the file with CD-Text data to 'name'
cuefile=name Set the file with CDRWIN CUE data to 'name'
-audio Subsequent tracks are CD-DA audio tracks
-data Subsequent tracks are CD-ROM data mode 1 -
2048 bytes (d
efault)
-mode2 Subsequent tracks are CD-ROM data mode 2 -
2336 bytes
-xa Subsequent tracks are CD-ROM XA mode 2 form
1 - 2048 byt
es
-xa1 Subsequent tracks are CD-ROM XA mode 2 form
1 - 2056 byt
es
-xa2 Subsequent tracks are CD-ROM XA mode 2 form
2 - 2324 byt
es
-xamix Subsequent tracks are CD-ROM XA mode 2 form
1/2 - 2332 b
ytes
-cdi Subsequent tracks are CDI tracks
-isosize Use iso9660 file system size for next data
track
-preemp Audio tracks are mastered with 50/15 ÷s
preemphasis
-nopreemp Audio tracks are mastered with no
preemphasis (default)
-copy Audio tracks have unlimited copy permission
-nocopy Audio tracks may only be copied once for
personal use (d
efault)
-scms Audio tracks will not have any copy
permission at all
-pad Pad data tracks with 15 zeroed sectors
Pad audio tracks to a multiple of 2352 bytes
-nopad Do not pad data tracks (default)
-shorttrack Subsequent tracks may be non Red Book < 4
seconds if in
SAO or RAW mode
-noshorttrack Subsequent tracks must be >= 4 seconds
-swab Audio data source is byte-swapped (little-
endian/Intel)
The type of the first track is used for the toc type.
Currently only form 1 tracks are supported.
And these options is only for cdrecord.exe. Folder cdrtools has
mkISOfs, readcd, and cddda2wav. With options, too.
So, we can use these tools to produce any cd/dvd by AutoIt, I think.
:-)
Valery
--- In [email protected], Steve <xirconuk@...> wrote:
>
> Valery
>
> Looks very interesting, shame there is no command line options so
that
> we can use from our scripts ;-)
>
> Steve
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/AutoItList/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/AutoItList/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:[email protected]
mailto:[email protected]
<*> To unsubscribe from this group, send an email to:
[email protected]
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/