Re: Re: Ctl-E not working

Hi Joseph,

The most likely, is that Gui4Cli wasn't installed correctly. The installer
will copy all the utility guis to the Gui4Cli directory and create the
initial setup so it knows where to find them.

The easiest would be to re-install it. You can download the full
installer-driven copy from the website.

Dimitris



On Sat, Dec 21, 2013 at 11:17 AM, jd <[email protected]> wrote:

>
>
> Hello Dimitris
>
> The Gui4Cli prefs program does not appear in the list obtained by right
> clicking
>
>
> Joseph
>
> On 20/12/2013, you wrote:
>
> > Hi Joseph,
> >
> > The only other thing I can think of is that the default guis have somehow
> > been changed.
> >
> > Load the "Preferences" gui, go to the "Auto Gui" tab, and then in the
> > item "Editor gui", browse for the edGotoLine.gc gui
> >
> >
> > Dimitris
> >
> >
> >
> > On Fri, Dec 20, 2013 at 4:05 PM, jd <[email protected]> wrote:
> >
> >>
> >>
> >> Hello Dimitris
> >>
> >> The file is there, although with the name (no capital E)
> >> edGotoLine.gc
> >>
> >> This is for my grandsons instaal
> >>
> >> I verified also on my install: the file is there too with the same
> >> no-capital
> >> E name ., and i hav no such problems with Ctrl-E
> >>
> >> Joseph
> >>
> >>
> >> On 20/12/2013, you wrote:
> >>
> >> > Hi Joseph,
> >> >
> >> > From what it says, its not finding the file INSTALL:Util/EdGotoLine.gc
> >> >
> >> > This should be the in gui4cli/util directory.
> >> > It is copied there during installation.
> >> > Can you check if its there?
> >> >
> >> > Dimitris
> >> >
> >> >
> >> > On Fri, Dec 20, 2013 at 10:31 AM, jd <[email protected]> wrote:
> >> >
> >> >>
> >> >>
> >> >> Hello Dimitris
> >> >>
> >> >> When using Ctl-E the following message occurs
> >> >>
> >> >> *ERROR* [19:18:57} File: "D:/Gui4Cli/Gui/Spellcheck...
> >> >> File not found, INSTALL:Util/EdGotoLine.gc
> >> >>
> >> >> Ctl-R seems to work OK
> >> >>
> >> >> Joseph
> >> >>
> >> >>
> >> >> On 10/12/2013, you wrote:
> >> >>
> >> >> > It may sometimes not work, if the cursor is in a textbox, or
> >> >> > textin, uch, because there the control itself "eats" the
>
> >> >> > keystroke.
> >>
> >> >> >
> >> >> > Just click some other control and it should work.
> >> >> >
> >> >> > Dimitris
> >> >> >
> >> >> >
> >> >> > On Mon, Dec 9, 2013 at 8:49 PM, jd <[email protected]> wrote:
> >> >> >
> >> >> >>
> >> >> >>
> >> >> >> Hello
> >> >> >>
> >> >> >> I am tyring to convince my grandson to use and program in Gui4Cli
> >> >> >> I downloaded the latest version (2012) and installed it.
> >> >> >> However Ctl-E did not work.
> >> >> >>
> >> >> >> Suggestions?
> >> >> >>
> >> >> >> Joseph
> >> >> >>
> >> >> >>
> >> >> >>
> >> >> Regards
> >> >>
> >> >>
> >> >>
> >> Regards
> >>
> >>
> >>
> Regards
>
>  
>