Re: Non functional DRI
Owen Savill <[email protected]>
| Newsgroups | gmane.comp.xfree86.expert |
|---|---|
| Message-ID | <[email protected]> |
Sorry if you have already been told this. I fell into this trap untill
it was pointed ot that you need
Section "DRI"
Mode 0666
EndSection
in your XF86Config file.
Hope this helps,
Owen
Mukhben Singh wrote:
>
> Hi,
> I have been struggling with it for almost a week now. I have
> compiled the kernel over and over again, changed the X Config file
> numerous times but still am not getting the expected results. To cut a
> long story short, the frame rate in tuxracer is pathetic. Actually in the
> log files, DRI and AGPart are reported to be enabled, but still glxinfo
> returns Direct Rendering: NO and I guess that is why the frame rates are
> so bad. Also the display in TUXRACER is garbled.
> The new kernel which I compiled after applying the suggested (
> suggested by Thomas who has written drivers for my vid card ) code for the
> kernel frame buffer, seems to work fine except for a couple of modules
> which are not related to video display ( supermount and sound ). I am
> attaching all the relevant files.
> System Details:
> K7SEM mobo
> AMD Duron 800 MHz
> 128 MB RAM (32 MB shared vid mem)
> SiS730S chipset
> Onboard sound and Video
> Base Installation: Mandrake 9.0
> Compiled Kernel 2.4.19
> 1024x768 @ 24bpp
> Please advice.
>
> Thanks in advance,
> Mukhben.
>
>
>
> ------------------------------------------------------------------------
>
> Linux version 2.4.19 ([email protected]) (gcc version 3.2 (Mandrake Linux 9.0 3.2-1mdk)) #2 Sun Nov 24 19:27:18 GMT 2002
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000005ff0000 (usable)
> BIOS-e820: 0000000005ff0000 - 0000000005ff3000 (ACPI NVS)
> BIOS-e820: 0000000005ff3000 - 0000000006000000 (ACPI data)
> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> 95MB LOWMEM available.
> Advanced speculative caching feature not present
> On node 0 totalpages: 24560
> zone(0): 4096 pages.
> zone(1): 20464 pages.
> zone(2): 0 pages.
> Kernel command line: BOOT_IMAGE=linux-exp ro root=307 devfs=mount,video=sisfb:mode:none,mem=12288
> Local APIC disabled by BIOS -- reenabling.
> Found and enabled local APIC!
> Initializing CPU#0
> Detected 801.827 MHz processor.
> Console: colour VGA+ 80x25
> Calibrating delay loop... 1599.07 BogoMIPS
> Memory: 94872k/98240k available (1152k kernel code, 2980k reserved, 401k data, 116k init, 0k highmem)
> Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
> Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
> Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
> Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
> Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
> CPU: Before vendor init, caps: 0183fbff c1c7fbff 00000000, vendor = 2
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 64K (64 bytes/line)
> CPU: After vendor init, caps: 0183fbff c1c7fbff 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: After generic, caps: 0183fbff c1c7fbff 00000000 00000000
> CPU: Common caps: 0183fbff c1c7fbff 00000000 00000000
> CPU: AMD Duron(tm) Processor stepping 01
> Enabling fast FPU save and restore... done.
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> enabled ExtINT on CPU#0
> ESR value before enabling vector: 00000000
> ESR value after enabling vector: 00000000
> Using local APIC timer interrupts.
> calibrating APIC timer ...
> ..... CPU clock speed is 801.8231 MHz.
> ..... host bus clock speed is 200.4556 MHz.
> cpu: 0, clocks: 2004556, slice: 1002278
> CPU0<T0:2004544,T1:1002256,D:10,S:1002278,C:2004556>
> mtrr: v1.40 (20010327) Richard Gooch ([email protected])
> mtrr: detected mtrr type: Intel
> PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> PCI: Using IRQ router SIS [1039/0008] at 00:01.0
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
> apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
> Starting kswapd
> VFS: Diskquotas version dquot_6.4.0 initialized
> devfs: v1.12a (20020514) Richard Gooch ([email protected])
> devfs: boot_options: 0x1
> sisfb: Video ROM found and mapped to c00c0000
> sisfb: Framebuffer at 0xd0000000, mapped to 0xc6804000, size 32768k
> sisfb: MMIO at 0xdc000000, mapped to 0xc8805000, size 128k
> sisfb: Memory heap starting at 12288K
> sisfb: SiS301LVX bridge detected (revision 0xff)
> sisfb: Mode is 800x600x8 (60Hz)
> sisfb: Added MTRRs
> Console: switching to colour frame buffer device 100x37
> sisfb: Installed SISFB_GET_INFO ioctl (80046ef8)
> sisfb: 2D acceleration is enabled, scrolling mode ypan
> fb0: SIS 730 frame buffer device, Version 1.5.11
> pty: 256 Unix98 ptys configured
> Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> SIS5513: IDE controller on PCI bus 00 dev 01
> SIS5513: chipset revision 208
> SIS5513: not 100% native mode: will probe irqs later
> SiS730
> ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:pio, hdd:pio
> hda: WDC WD200EB-11BHF0, ATA DISK drive
> hdb: CD-ROM Drive/G6D, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=2434/255/63, UDMA(100)
> Partition check:
> /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
> PPP generic driver version 2.4.2
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> IP: routing cache hash table of 512 buckets, 4Kbytes
> TCP: Hash tables configured (established 8192 bind 16384)
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> VFS: Mounted root (ext2 filesystem) readonly.
> Mounted devfs on /dev
> Freeing unused kernel memory: 116k freed
> Real Time Clock Driver v1.10e
> usb.c: registered new driver usbdevfs
> usb.c: registered new driver hub
> PCI: Found IRQ 5 for device 00:01.2
> PCI: Sharing IRQ 5 with 00:01.3
> usb-ohci.c: USB OHCI at membase 0xc8841000, IRQ 5
> usb-ohci.c: usb-00:01.2, Silicon Integrated Systems [SiS] 7001
> usb.c: new USB bus registered, assigned bus number 1
> hub.c: USB hub found
> hub.c: 3 ports detected
> PCI: Found IRQ 5 for device 00:01.3
> PCI: Sharing IRQ 5 with 00:01.2
> usb-ohci.c: USB OHCI at membase 0xc8843000, IRQ 5
> usb-ohci.c: usb-00:01.3, Silicon Integrated Systems [SiS] 7001 (#2)
> usb.c: new USB bus registered, assigned bus number 2
> hub.c: USB hub found
> hub.c: 3 ports detected
> usbdevfs: remount parameter error
> Adding Swap: 257000k swap-space (priority -1)
> MSDOS FS: IO charset iso8859-15
> MSDOS FS: Using codepage 850
> FAT: freeing iocharset=iso8859-15
> MSDOS FS: IO charset iso8859-15
> MSDOS FS: Using codepage 850
> FAT: freeing iocharset=iso8859-15
>
>
> ------------------------------------------------------------------------
>
> name of display: :0.0
> display: :0 screen: 0
> direct rendering: No
> server glx vendor string: SGI
> server glx version string: 1.2
> server glx extensions:
> GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context
> client glx vendor string: SGI
> client glx version string: 1.2
> client glx extensions:
> GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context
> GLX extensions:
> GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context
> OpenGL vendor string: VA Linux Systems, Inc.
> OpenGL renderer string: Mesa GLX Indirect
> OpenGL version string: 1.2 Mesa 3.4.2
> OpenGL extensions:
> GL_ARB_multitexture, GL_EXT_abgr, GL_EXT_blend_color,
> GL_EXT_blend_minmax, GL_EXT_blend_subtract
> glu version: 1.3
> glu extensions:
> GLU_EXT_nurbs_tessellator, GLU_EXT_object_space_tess
>
> visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
> id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
> ----------------------------------------------------------------------
> 0x22 24 tc 0 24 0 r . . 8 8 8 0 0 0 0 0 0 0 0 0 0 None
> 0x23 24 tc 0 24 0 r y . 8 8 8 0 0 0 0 0 0 0 0 0 0 None
> 0x24 24 tc 0 24 0 r . . 8 8 8 0 0 16 0 0 0 0 0 0 0 None
> 0x25 24 tc 0 24 0 r y . 8 8 8 0 0 16 0 0 0 0 0 0 0 None
> 0x26 24 tc 0 24 0 r . . 8 8 8 0 0 32 0 0 0 0 0 0 0 None
> 0x27 24 tc 0 24 0 r y . 8 8 8 0 0 32 0 0 0 0 0 0 0 None
> 0x28 24 tc 0 24 0 r . . 8 8 8 0 0 24 8 0 0 0 0 0 0 None
> 0x29 24 tc 0 24 0 r y . 8 8 8 0 0 24 8 0 0 0 0 0 0 None
> 0x2a 24 tc 0 24 0 r . . 8 8 8 0 0 0 0 16 16 16 16 0 0 None
> 0x2b 24 tc 0 24 0 r y . 8 8 8 0 0 0 0 16 16 16 16 0 0 None
> 0x2c 24 tc 0 24 0 r . . 8 8 8 0 0 16 0 16 16 16 16 0 0 None
> 0x2d 24 tc 0 24 0 r y . 8 8 8 0 0 16 0 16 16 16 16 0 0 None
> 0x2e 24 tc 0 24 0 r . . 8 8 8 0 0 32 0 16 16 16 16 0 0 None
> 0x2f 24 tc 0 24 0 r y . 8 8 8 0 0 32 0 16 16 16 16 0 0 None
> 0x30 24 tc 0 24 0 r . . 8 8 8 0 0 24 8 16 16 16 16 0 0 None
> 0x31 24 tc 0 24 0 r y . 8 8 8 0 0 24 8 16 16 16 16 0 0 None
>
>
> ------------------------------------------------------------------------
>
> # File generated by XFdrake.
>
> # **********************************************************************
> # Refer to the XF86Config man page for details about the format of
> # this file.
> # **********************************************************************
>
> Section "Files"
> # Multiple FontPath entries are allowed (they are concatenated together)
> # By default, Mandrake 6.0 and later now use a font server independent of
> # the X server to render fonts.
> FontPath "unix/:-1"
> EndSection
>
> Section "ServerFlags"
> #DontZap # disable <Crtl><Alt><BS> (server abort)
> #DontZoom # disable <Crtl><Alt><KP_+>/<KP_-> (resolution switching)
> AllowMouseOpenFail # allows the server to start up even if the mouse doesn't work
> EndSection
>
> Section "Module"
> Load "ddc"
> Load "GLcore"
> Load "dbe"
> Load "dri"
> Load "extmod"
> Load "glx"
> #Load "pex5"
> Load "record"
> #Load "xie"
> Load "bitmap"
> Load "freetype"
> Load "speedo"
> Load "type1"
> Load "vbe"
> Load "int10"
> EndSection
>
> Section "InputDevice"
> Identifier "Keyboard1"
> Driver "Keyboard"
> Option "XkbModel" "pc105"
> Option "XkbLayout" "gb"
> Option "XkbOptions" ""
> EndSection
>
> Section "InputDevice"
> Identifier "Mouse1"
> Driver "mouse"
> Option "Protocol" "PS/2"
> Option "Device" "/dev/psaux"
> Option "Emulate3Buttons"
> Option "Emulate3Timeout" "50"
> EndSection
>
> Section "Monitor"
> Identifier "monitor1"
> VendorName "Plug'n Play"
> ModelName "LG StudioWorks 56i"
> HorizSync 30.0-65.0
> VertRefresh 50.0-120.0
>
> # Sony Vaio C1(X,XS,VE,VN)?
> # 1024x480 @ 85.6 Hz, 48 kHz hsync
> ModeLine "1024x480" 65.00 1024 1032 1176 1344 480 488 494 563 -hsync -vsync
>
> # TV fullscreen mode or DVD fullscreen output.
> # 768x576 @ 79 Hz, 50 kHz hsync
> ModeLine "768x576" 50.00 768 832 846 1000 576 590 595 630
>
> # 768x576 @ 100 Hz, 61.6 kHz hsync
> ModeLine "768x576" 63.07 768 800 960 1024 576 578 590 616
> EndSection
>
> Section "Device"
> Identifier "device1"
> VendorName "Silicon Integrated Systems [SiS]"
> BoardName "SiS 630"
> Driver "sis"
> Option "DPMS"
> Option "MaxXFBMem" "12288"
> #Option "hw_cursor" "false" # Added on 15/11/2002 by Mukhben
> EndSection
>
> Section "Screen"
> Identifier "screen1"
> Device "device1"
> Monitor "monitor1"
> DefaultColorDepth 24
>
> Subsection "Display"
> Depth 8
> Modes "1024x768" "800x600" "640x480"
> EndSubsection
>
> Subsection "Display"
> Depth 15
> Modes "1024x768" "800x600" "640x480"
> EndSubsection
>
> Subsection "Display"
> Depth 16
> Modes "1024x768" "800x600" "640x480"
> EndSubsection
>
> Subsection "Display"
> Depth 24
> Modes "1024x768" "800x600" "640x480"
> EndSubsection
> EndSection
>
> Section "ServerLayout"
> Identifier "layout1"
> InputDevice "Keyboard1" "CoreKeyboard"
> InputDevice "Mouse1" "CorePointer"
> Screen "screen1"
> EndSection
>
> Section "DRI"
> Mode 0666
> EndSection
>
>
> ------------------------------------------------------------------------
>
> 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 730 Host (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 32
> Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=64M]
> Capabilities: <available only to root>
>
> 00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
> Subsystem: Elitegroup Computer Systems: Unknown device 0a01
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 16
> Region 4: I/O ports at 4000 [size=16]
>
> 00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:01.2 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 07) (prog-if 10 [OHCI])
> Subsystem: Silicon Integrated Systems [SiS] 7001
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), cache line size 08
> Interrupt: pin D routed to IRQ 5
> Region 0: Memory at dc101000 (32-bit, non-prefetchable) [size=4K]
>
> 00:01.3 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 07) (prog-if 10 [OHCI])
> Subsystem: Silicon Integrated Systems [SiS]: Unknown device 7000
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), cache line size 08
> Interrupt: pin D routed to IRQ 5
> Region 0: Memory at dc102000 (32-bit, non-prefetchable) [size=4K]
>
> 00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 02)
> Subsystem: Elitegroup Computer Systems: Unknown device 0a01
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (500ns min, 6000ns max)
> Interrupt: pin B routed to IRQ 11
> Region 0: I/O ports at e000 [size=256]
> Region 1: Memory at dc100000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: <available only to root>
>
> 00:02.0 PCI bridge: Silicon Integrated Systems [SiS] 5591/5592 AGP (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: dc000000-dc0fffff
> Prefetchable memory behind bridge: d0000000-d7ffffff
> BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
>
> 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] SiS630 GUI Accelerator+3D (rev 31) (prog-if 00 [VGA])
> Subsystem: Elitegroup Computer Systems: Unknown device 0a01
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> BIST result: 00
> Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
> Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=128K]
> Region 2: I/O ports at d000 [size=128]
> Capabilities: <available only to root>
>
>
> ------------------------------------------------------------------------
>
>
> XFree86 Version 4.2.1 / X Window System
> (protocol Version 11, revision 0, vendor release 6600)
> Release Date: 3 September 2002
> If the server is older than 6-12 months, or if your card is
> newer than the above date, look for a newer version before
> reporting problems. (See http://www.XFree86.Org/)
> Build Operating System: Linux 2.4.18-23mdkenterprise i686 [ELF]
> Module Loader present
> Markers: (--) probed, (**) from config file, (==) default setting,
> (++) from command line, (!!) notice, (II) informational,
> (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
> (==) Log file: "/var/log/XFree86.0.log", Time: Sun Nov 24 22:48:48 2002
> (==) Using config file: "/etc/X11/XF86Config-4"
> (==) ServerLayout "layout1"
> (**) |-->Screen "screen1" (0)
> (**) | |-->Monitor "monitor1"
> (**) | |-->Device "device1"
> (**) |-->Input Device "Keyboard1"
> (**) Option "XkbModel" "pc105"
> (**) XKB: model: "pc105"
> (**) Option "XkbLayout" "gb"
> (**) XKB: layout: "gb"
> (WW) Option "XkbOptions" requires an string value
> (==) Keyboard: CustomKeycode disabled
> (**) |-->Input Device "Mouse1"
> (**) FontPath set to "unix/:-1"
> (==) RgbPath set to "/usr/X11R6/lib/X11/rgb"
> (==) ModulePath set to "/usr/X11R6/lib/modules"
> (**) Option "AllowMouseOpenFail"
> Using vt 7
> (--) using VT number 7
>
> (II) Open APM successful
> (II) Module ABI versions:
> XFree86 ANSI C Emulation: 0.1
> XFree86 Video Driver: 0.5
> XFree86 XInput driver : 0.3
> XFree86 Server Extension : 0.1
> XFree86 Font Renderer : 0.3
> (II) Loader running on linux
> (II) LoadModule: "bitmap"
> (II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
> (II) Module bitmap: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> Module class: XFree86 Font Renderer
> ABI class: XFree86 Font Renderer, version 0.3
> (II) Loading font Bitmap
> (II) LoadModule: "pcidata"
> (II) Loading /usr/X11R6/lib/modules/libpcidata.a
> (II) Module pcidata: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 0.1.0
> ABI class: XFree86 Video Driver, version 0.5
> (II) PCI: Probing config type using method 1
> (II) PCI: Config type is 1
> (II) PCI: stages = 0x03, oldVal1 = 0x80000140, mode1Res1 = 0x80000000
> (II) PCI: PCI scan (all values are in hex)
> (II) PCI: 00:00:0: chip 1039,0730 card 0000,0000 rev 02 class 06,00,00 hdr 80
> (II) PCI: 00:00:1: chip 1039,5513 card 1019,0a01 rev d0 class 01,01,80 hdr 80
> (II) PCI: 00:01:0: chip 1039,0008 card 0000,0000 rev 00 class 06,01,00 hdr 80
> (II) PCI: 00:01:2: chip 1039,7001 card 1039,7001 rev 07 class 0c,03,10 hdr 00
> (II) PCI: 00:01:3: chip 1039,7001 card 1039,7000 rev 07 class 0c,03,10 hdr 00
> (II) PCI: 00:01:4: chip 1039,7018 card 1019,0a01 rev 02 class 04,01,00 hdr 00
> (II) PCI: 00:02:0: chip 1039,0001 card 0000,0000 rev 00 class 06,04,00 hdr 01
> (II) PCI: 01:00:0: chip 1039,6300 card 1019,0a01 rev 31 class 03,00,00 hdr 00
> (II) PCI: End of PCI scan
> (II) LoadModule: "scanpci"
> (II) Loading /usr/X11R6/lib/modules/libscanpci.a
> (II) Module scanpci: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 0.1.0
> ABI class: XFree86 Video Driver, version 0.5
> (II) UnloadModule: "scanpci"
> (II) Unloading /usr/X11R6/lib/modules/libscanpci.a
> (II) Host-to-PCI bridge:
> (II) PCI-to-ISA bridge:
> (II) PCI-to-PCI bridge:
> (II) Bus 0: bridge is at (0:0:0), (-1,0,0), BCTRL: 0x08 (VGA_EN is set)
> (II) Bus 0 I/O range:
> [0] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
> (II) Bus 0 non-prefetchable memory range:
> [0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
> (II) Bus 0 prefetchable memory range:
> [0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
> (II) Bus -1: bridge is at (0:1:0), (0,-1,0), BCTRL: 0x08 (VGA_EN is set)
> (II) Bus -1 I/O range:
> (II) Bus -1 non-prefetchable memory range:
> (II) Bus -1 prefetchable memory range:
> (II) Bus 1: bridge is at (0:2:0), (0,1,1), BCTRL: 0x0e (VGA_EN is set)
> (II) Bus 1 I/O range:
> [0] -1 0x0000d000 - 0x0000d0ff (0x100) IX[B]
> [1] -1 0x0000d400 - 0x0000d4ff (0x100) IX[B]
> [2] -1 0x0000d800 - 0x0000d8ff (0x100) IX[B]
> [3] -1 0x0000dc00 - 0x0000dcff (0x100) IX[B]
> (II) Bus 1 non-prefetchable memory range:
> [0] -1 0xdc000000 - 0xdc0fffff (0x100000) MX[B]
> (II) Bus 1 prefetchable memory range:
> [0] -1 0xd0000000 - 0xd7ffffff (0x8000000) MX[B]
> (--) PCI:*(1:0:0) SiS 630 rev 49, Mem @ 0xd0000000/27, 0xdc000000/17, I/O @ 0xd000/7
> (II) Addressable bus resource ranges are
> [0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
> [1] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
> (II) OS-reported resource ranges:
> [0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
> [1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
> [2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
> [3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
> [4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
> [5] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
> [6] -1 0x00000000 - 0x000000ff (0x100) IX[B]
> (II) Active PCI resource ranges:
> [0] -1 0xdc100000 - 0xdc100fff (0x1000) MX[B]
> [1] -1 0xdc102000 - 0xdc102fff (0x1000) MX[B]
> [2] -1 0xdc101000 - 0xdc101fff (0x1000) MX[B]
> [3] -1 0xd8000000 - 0xdbffffff (0x4000000) MX[B]
> [4] -1 0xdc000000 - 0xdc01ffff (0x20000) MX[B](B)
> [5] -1 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
> [6] -1 0x0000e000 - 0x0000e0ff (0x100) IX[B]
> [7] -1 0x00004000 - 0x0000400f (0x10) IX[B]
> [8] -1 0x0000d000 - 0x0000d07f (0x80) IX[B](B)
> (II) Active PCI resource ranges after removing overlaps:
> [0] -1 0xdc100000 - 0xdc100fff (0x1000) MX[B]
> [1] -1 0xdc102000 - 0xdc102fff (0x1000) MX[B]
> [2] -1 0xdc101000 - 0xdc101fff (0x1000) MX[B]
> [3] -1 0xd8000000 - 0xdbffffff (0x4000000) MX[B]
> [4] -1 0xdc000000 - 0xdc01ffff (0x20000) MX[B](B)
> [5] -1 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
> [6] -1 0x0000e000 - 0x0000e0ff (0x100) IX[B]
> [7] -1 0x00004000 - 0x0000400f (0x10) IX[B]
> [8] -1 0x0000d000 - 0x0000d07f (0x80) IX[B](B)
> (II) OS-reported resource ranges after removing overlaps with PCI:
> [0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
> [1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
> [2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
> [3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
> [4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
> [5] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
> [6] -1 0x00000000 - 0x000000ff (0x100) IX[B]
> (II) All system resource ranges:
> [0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
> [1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
> [2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
> [3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
> [4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
> [5] -1 0xdc100000 - 0xdc100fff (0x1000) MX[B]
> [6] -1 0xdc102000 - 0xdc102fff (0x1000) MX[B]
> [7] -1 0xdc101000 - 0xdc101fff (0x1000) MX[B]
> [8] -1 0xd8000000 - 0xdbffffff (0x4000000) MX[B]
> [9] -1 0xdc000000 - 0xdc01ffff (0x20000) MX[B](B)
> [10] -1 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
> [11] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
> [12] -1 0x00000000 - 0x000000ff (0x100) IX[B]
> [13] -1 0x0000e000 - 0x0000e0ff (0x100) IX[B]
> [14] -1 0x00004000 - 0x0000400f (0x10) IX[B]
> [15] -1 0x0000d000 - 0x0000d07f (0x80) IX[B](B)
> (II) LoadModule: "ddc"
> (II) Loading /usr/X11R6/lib/modules/libddc.a
> (II) Module ddc: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> ABI class: XFree86 Video Driver, version 0.5
> (II) LoadModule: "GLcore"
> (II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a
> (II) Module GLcore: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> ABI class: XFree86 Server Extension, version 0.1
> (II) LoadModule: "dbe"
> (II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
> (II) Module dbe: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> Module class: XFree86 Server Extension
> ABI class: XFree86 Server Extension, version 0.1
> (II) Loading extension DOUBLE-BUFFER
> (II) LoadModule: "dri"
> (II) Loading /usr/X11R6/lib/modules/extensions/libdri.a
> (II) Module dri: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> ABI class: XFree86 Server Extension, version 0.1
> (II) Loading sub module "drm"
> (II) LoadModule: "drm"
> (II) Loading /usr/X11R6/lib/modules/linux/libdrm.a
> (II) Module drm: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> ABI class: XFree86 Server Extension, version 0.1
> (II) Loading extension XFree86-DRI
> (II) LoadModule: "extmod"
> (II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
> (II) Module extmod: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> Module class: XFree86 Server Extension
> ABI class: XFree86 Server Extension, version 0.1
> (II) Loading extension SHAPE
> (II) Loading extension MIT-SUNDRY-NONSTANDARD
> (II) Loading extension BIG-REQUESTS
> (II) Loading extension SYNC
> (II) Loading extension MIT-SCREEN-SAVER
> (II) Loading extension XC-MISC
> (II) Loading extension XFree86-VidModeExtension
> (II) Loading extension XFree86-Misc
> (II) Loading extension XFree86-DGA
> (II) Loading extension DPMS
> (II) Loading extension FontCache
> (II) Loading extension TOG-CUP
> (II) Loading extension Extended-Visual-Information
> (II) Loading extension XVideo
> (II) Loading extension XVideo-MotionCompensation
> (II) LoadModule: "glx"
> (II) Loading /usr/X11R6/lib/modules/extensions/libglx.a
> (II) Module glx: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> ABI class: XFree86 Server Extension, version 0.1
> (II) Loading sub module "GLcore"
> (II) LoadModule: "GLcore"
> (II) Reloading /usr/X11R6/lib/modules/extensions/libGLcore.a
> (II) Loading extension GLX
> (II) LoadModule: "record"
> (II) Loading /usr/X11R6/lib/modules/extensions/librecord.a
> (II) Module record: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.13.0
> Module class: XFree86 Server Extension
> ABI class: XFree86 Server Extension, version 0.1
> (II) Loading extension RECORD
> (II) LoadModule: "bitmap"
> (II) Reloading /usr/X11R6/lib/modules/fonts/libbitmap.a
> (II) Loading font Bitmap
> (II) LoadModule: "freetype"
> (II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.a
> (II) Module freetype: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.1.10
> Module class: XFree86 Font Renderer
> ABI class: XFree86 Font Renderer, version 0.3
> (II) Loading font FreeType
> (II) LoadModule: "speedo"
> (II) Loading /usr/X11R6/lib/modules/fonts/libspeedo.a
> (II) Module speedo: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.1
> Module class: XFree86 Font Renderer
> ABI class: XFree86 Font Renderer, version 0.3
> (II) Loading font Speedo
> (II) LoadModule: "type1"
> (II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
> (II) Module type1: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.1
> Module class: XFree86 Font Renderer
> ABI class: XFree86 Font Renderer, version 0.3
> (II) Loading font Type1
> (II) Loading font CID
> (II) LoadModule: "vbe"
> (II) Loading /usr/X11R6/lib/modules/libvbe.a
> (II) Module vbe: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> ABI class: XFree86 Video Driver, version 0.5
> (II) LoadModule: "int10"
> (II) Loading /usr/X11R6/lib/modules/linux/libint10.a
> (II) Module int10: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> ABI class: XFree86 Video Driver, version 0.5
> (II) LoadModule: "sis"
> (II) Loading /usr/X11R6/lib/modules/drivers/sis_drv.o
> (II) Module sis: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 0.6.0
> Module class: XFree86 Video Driver
> ABI class: XFree86 Video Driver, version 0.5
> (II) LoadModule: "mouse"
> (II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
> (II) Module mouse: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> Module class: XFree86 XInput Driver
> ABI class: XFree86 XInput driver, version 0.3
> (II) SIS: driver for SiS chipsets: SIS5597/5598, SIS530/620,
> SIS6326/AGP/DVD, SIS300/305, SIS630/730, SIS540, SIS315, SIS315H,
> SIS315PRO, SIS550, SIS650/M650/651/740, SIS330(Xabre)
> (II) Primary Device is: PCI 01:00:0
> (--) Assigning device section with no busID to primary device
> (--) Chipset SIS630/730 found
> (II) resource ranges after xf86ClaimFixedResources() call:
> [0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
> [1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
> [2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
> [3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
> [4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
> [5] -1 0xdc100000 - 0xdc100fff (0x1000) MX[B]
> [6] -1 0xdc102000 - 0xdc102fff (0x1000) MX[B]
> [7] -1 0xdc101000 - 0xdc101fff (0x1000) MX[B]
> [8] -1 0xd8000000 - 0xdbffffff (0x4000000) MX[B]
> [9] -1 0xdc000000 - 0xdc01ffff (0x20000) MX[B](B)
> [10] -1 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
> [11] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
> [12] -1 0x00000000 - 0x000000ff (0x100) IX[B]
> [13] -1 0x0000e000 - 0x0000e0ff (0x100) IX[B]
> [14] -1 0x00004000 - 0x0000400f (0x10) IX[B]
> [15] -1 0x0000d000 - 0x0000d07f (0x80) IX[B](B)
> (II) resource ranges after probing:
> [0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
> [1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
> [2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
> [3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
> [4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
> [5] -1 0xdc100000 - 0xdc100fff (0x1000) MX[B]
> [6] -1 0xdc102000 - 0xdc102fff (0x1000) MX[B]
> [7] -1 0xdc101000 - 0xdc101fff (0x1000) MX[B]
> [8] -1 0xd8000000 - 0xdbffffff (0x4000000) MX[B]
> [9] -1 0xdc000000 - 0xdc01ffff (0x20000) MX[B](B)
> [10] -1 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
> [11] 0 0x000a0000 - 0x000affff (0x10000) MS[B]
> [12] 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
> [13] 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
> [14] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
> [15] -1 0x00000000 - 0x000000ff (0x100) IX[B]
> [16] -1 0x0000e000 - 0x0000e0ff (0x100) IX[B]
> [17] -1 0x00004000 - 0x0000400f (0x10) IX[B]
> [18] -1 0x0000d000 - 0x0000d07f (0x80) IX[B](B)
> [19] 0 0x000003b0 - 0x000003bb (0xc) IS[B]
> [20] 0 0x000003c0 - 0x000003df (0x20) IS[B]
> (II) Setting vga for screen 0.
> (II) Loading sub module "vgahw"
> (II) LoadModule: "vgahw"
> (II) Loading /usr/X11R6/lib/modules/libvgahw.a
> (II) Module vgahw: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 0.1.0
> ABI class: XFree86 Video Driver, version 0.5
> (II) SIS(0): SiS driver (02/10/31-1) by Thomas Winischhofer <[email protected]>
> (--) SIS(0): This adapter is primary display adapter
> (II) SIS(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
> (II) Loading sub module "ramdac"
> (II) LoadModule: "ramdac"
> (II) Loading /usr/X11R6/lib/modules/libramdac.a
> (II) Module ramdac: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 0.1.0
> ABI class: XFree86 Video Driver, version 0.5
> (--) SIS(0): fb0: SiS kernel fb driver (sisfb) 1.5.11 detected (PCI: 01:00.0)
> (--) SIS(0): sisfb: memory heap starts at 12288KB
> (--) SIS(0): sisfb: using video mode 0x30
> (--) SIS(0): sisfb: reserved hardware cursor, using SiS300 series Turbo command queue
> (--) SIS(0): Relocated IO registers at 0xD000
> (**) SIS(0): Depth 24, (--) framebuffer bpp 32
> (==) SIS(0): RGB weight 888
> (==) SIS(0): Default visual is TrueColor
> (==) SIS(0): Using gamma correction (1.0, 1.0, 1.0)
> (**) SIS(0): Option "MaxXFBMem" "12288"
> (==) SIS(0): Using HW cursor
> (==) SIS(0): PCI retry enabled
> (==) SIS(0): TurboQueue enabled
> (**) SIS(0): MaxXFBMem: Framebuffer memory shall be limited to 12288 KB
> (==) SIS(0): Usage of built-in modes is enabled
> (--) SIS(0): Video ROM data usage is enabled
> (--) SIS(0): Detected DRAM type: SDRAM
> (--) SIS(0): Detected memory clock: 100.226 MHz
> (--) SIS(0): (Adapter assumes MCLK being 100 Mhz)
> (--) SIS(0): Detected DRAM bus width: 64 bit
> (--) SIS(0): Global linear framebuffer at 0xD0000000
> (--) SIS(0): MMIO registers at 0xDC000000
> (--) SIS(0): VideoRAM: 32768 KB
> (II) SIS(0): Using 12288K of framebuffer memory
> (--) SIS(0): Chipset supports two video overlays
> (--) SIS(0): Memory bandwidth at 32 bpp is 200.452 MHz
> (II) Loading sub module "ddc"
> (II) LoadModule: "ddc"
> (II) Reloading /usr/X11R6/lib/modules/libddc.a
> (--) SIS(0): CRT1 DDC supported
> (--) SIS(0): CRT1 DDC level: 2
> (--) SIS(0): DDC monitor info:
> (II) SIS(0): Manufacturer: GSM Model: 3aa8 Serial#: 0
> (II) SIS(0): Year: 1997 Week: 19
> (II) SIS(0): EDID Version: 1.1
> (II) SIS(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V
> (II) SIS(0): Signal levels configurable
> (II) SIS(0): Sync: Separate
> (II) SIS(0): Max H-Image Size [cm]: horiz.: 28 vert.: 21
> (II) SIS(0): Gamma: 2.12
> (II) SIS(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
> (II) SIS(0): redX: 0.616 redY: 0.341 greenX: 0.277 greenY: 0.588
> (II) SIS(0): blueX: 0.143 blueY: 0.062 whiteX: 0.281 whiteY: 0.312
> (II) SIS(0): Supported VESA Video Modes:
> (II) SIS(0): 720x400@70Hz
> (II) SIS(0): 720x400@88Hz
> (II) SIS(0): 640x480@60Hz
> (II) SIS(0): 640x480@67Hz
> (II) SIS(0): 640x480@72Hz
> (II) SIS(0): 640x480@75Hz
> (II) SIS(0): 800x600@56Hz
> (II) SIS(0): 800x600@60Hz
> (II) SIS(0): 800x600@72Hz
> (II) SIS(0): 800x600@75Hz
> (II) SIS(0): 832x624@75Hz
> (II) SIS(0): 1024x768@87Hz (interlaced)
> (II) SIS(0): 1024x768@60Hz
> (II) SIS(0): 1024x768@70Hz
> (II) SIS(0): 1024x768@75Hz
> (II) SIS(0): Manufacturer's mask: 0
> (II) SIS(0): Supported Future Video Modes:
> (II) SIS(0): #0: hsize: 720 vsize 540 refresh: 70 vid: 19003
> (II) SIS(0): #1: hsize: 640 vsize 480 refresh: 60 vid: 16433
> (II) SIS(0): #2: hsize: 640 vsize 480 refresh: 75 vid: 20273
> (II) SIS(0): #3: hsize: 800 vsize 600 refresh: 75 vid: 20293
> (II) SIS(0): #4: hsize: 1024 vsize 768 refresh: 70 vid: 19041
> (II) SIS(0): #5: hsize: 1280 vsize 960 refresh: 60 vid: 16513
> (II) SIS(0): Supported additional Video Mode:
> (II) SIS(0): clock: 25.2 MHz Image Size: 260 x 190 mm
> (II) SIS(0): h_active: 640 h_sync: 656 h_sync_end 752 h_blank_end 800 h_border: 0
> (II) SIS(0): v_active: 480 v_sync: 490 v_sync_end 492 v_blanking: 525 v_border: 0
> (II) SIS(0): Supported additional Video Mode:
> (II) SIS(0): clock: 49.5 MHz Image Size: 260 x 190 mm
> (II) SIS(0): h_active: 800 h_sync: 816 h_sync_end 896 h_blank_end 1056 h_border: 0
> (II) SIS(0): v_active: 600 v_sync: 601 v_sync_end 604 v_blanking: 625 v_border: 0
> (II) SIS(0): Supported additional Video Mode:
> (II) SIS(0): clock: 75.0 MHz Image Size: 260 x 190 mm
> (II) SIS(0): h_active: 1024 h_sync: 1048 h_sync_end 1184 h_blank_end 1328 h_border: 0
> (II) SIS(0): v_active: 768 v_sync: 771 v_sync_end 777 v_blanking: 806 v_border: 0
> (II) SIS(0): Supported additional Video Mode:
> (II) SIS(0): clock: 108.0 MHz Image Size: 260 x 190 mm
> (II) SIS(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0
> (II) SIS(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0
> (--) SIS(0): End of DDC monitor info
> (==) SIS(0): Min pixel clock is 12 MHz
> (--) SIS(0): Max pixel clock is 139 MHz
> (II) SIS(0): Replaced default mode list with built-in modes
> (II) SIS(0): monitor1: Using hsync range of 30.00-65.00 kHz
> (II) SIS(0): monitor1: Using vrefresh range of 50.00-120.00 Hz
> (II) SIS(0): Clock range: 12.00 to 139.09 MHz
> (II) SIS(0): Not using default mode "800x600" (hsync out of range)
> (II) SIS(0): Not using default mode "800x600" (hsync out of range)
> (II) SIS(0): Not using default mode "800x600" (hsync out of range)
> (II) SIS(0): Not using default mode "640x480" (hsync out of range)
> (II) SIS(0): Not using default mode "640x480" (hsync out of range)
> (II) SIS(0): Not using default mode "640x480" (hsync out of range)
> (II) SIS(0): Not using default mode "1024x768" (hsync out of range)
> (II) SIS(0): Not using default mode "1024x768" (hsync out of range)
> (II) SIS(0): Not using default mode "1024x768" (hsync out of range)
> (II) SIS(0): Not using default mode "1280x1024" (hsync out of range)
> (II) SIS(0): Not using default mode "1280x1024" (bad mode clock/interlace/doublescan)
> (II) SIS(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
> (II) SIS(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
> (II) SIS(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
> (II) SIS(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
> (II) SIS(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
> (II) SIS(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
> (II) SIS(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
> (II) SIS(0): Not using default mode "1280x960" (hsync out of range)
> (II) SIS(0): Not using default mode "1280x960" (hsync out of range)
> (II) SIS(0): Not using default mode "1024x576" (hsync out of range)
> (II) SIS(0): Not using default mode "1280x720" (hsync out of range)
> (II) SIS(0): Not using default mode "1280x720" (bad mode clock/interlace/doublescan)
> (--) SIS(0): Virtual size is 1024x768 (pitch 1024)
> (**) SIS(0): Default mode "1024x768": 78.7 MHz, 60.0 kHz, 75.0 Hz
> (II) SIS(0): Modeline "1024x768" 78.75 1024 1040 1136 1312 768 796 799 800 +hsync +vsync
> (**) SIS(0): Default mode "800x600": 56.2 MHz, 53.7 kHz, 85.1 Hz
> (II) SIS(0): Modeline "800x600" 56.25 800 832 896 1048 600 627 630 631 +hsync +vsync
> (**) SIS(0): Default mode "640x480": 44.9 MHz, 54.4 kHz, 105.3 Hz
> (II) SIS(0): Modeline "640x480" 44.86 640 664 728 824 480 509 512 517 -hsync -vsync
> (--) SIS(0): Display dimensions: (280, 210) mm
> (--) SIS(0): DPI set to (92, 92)
> (II) Loading sub module "fb"
> (II) LoadModule: "fb"
> (II) Loading /usr/X11R6/lib/modules/libfb.a
> (II) Module fb: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> ABI class: XFree86 ANSI C Emulation, version 0.1
> (II) SIS(0): Accel enabled
> (II) Loading sub module "xaa"
> (II) LoadModule: "xaa"
> (II) Loading /usr/X11R6/lib/modules/libxaa.a
> (II) Module xaa: vendor="The XFree86 Project"
> compiled for 4.2.1, module version = 1.0.0
> ABI class: XFree86 Video Driver, version 0.5
> (==) Depth 24 pixmap format is 32 bpp
> (II) do I need RAC? No, I don't.
> (II) resource ranges after preInit:
> [0] 0 0xdc000000 - 0xdc01ffff (0x20000) MX[B]
> [1] 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B]
> [2] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
> [3] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
> [4] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
> [5] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
> [6] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
> [7] -1 0xdc100000 - 0xdc100fff (0x1000) MX[B]
> [8] -1 0xdc102000 - 0xdc102fff (0x1000) MX[B]
> [9] -1 0xdc101000 - 0xdc101fff (0x1000) MX[B]
> [10] -1 0xd8000000 - 0xdbffffff (0x4000000) MX[B]
> [11] -1 0xdc000000 - 0xdc01ffff (0x20000) MX[B](B)
> [12] -1 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
> [13] 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprU)
> [14] 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprU)
> [15] 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprU)
> [16] 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
> [17] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
> [18] -1 0x00000000 - 0x000000ff (0x100) IX[B]
> [19] -1 0x0000e000 - 0x0000e0ff (0x100) IX[B]
> [20] -1 0x00004000 - 0x0000400f (0x10) IX[B]
> [21] -1 0x0000d000 - 0x0000d07f (0x80) IX[B](B)
> [22] 0 0x000003b0 - 0x000003bb (0xc) IS[B]
> [23] 0 0x000003c0 - 0x000003df (0x20) IS[B]
> (II) SIS(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0xcc80
> (==) SIS(0): Write-combining range (0xd0000000,0x2000000)
> (II) SIS(0): VBFlags=0x20080000
> (--) SIS(0): Before: CR30=0x00, CR31=0x60, CR32=0x20, CR33=0x02
> (II) SIS(0): After: CR30=0x00, CR31=0x64, CR33=0x04
> (II) SIS(0): Setting mode 0x64
> (--) SIS(0): (init: VBType=0x0000, VBInfo=0x0000)
> drmOpenDevice: minor is 0
> drmOpenDevice: node name is /dev/dri/card0
> drmOpenDevice: open result is -1, (No such device)
> drmOpenDevice: Open failed
> drmOpenDevice: minor is 0
> drmOpenDevice: node name is /dev/dri/card0
> drmOpenDevice: open result is -1, (No such device)
> drmOpenDevice: Open failed
> drmOpenDevice: minor is 0
> drmOpenDevice: node name is /dev/dri/card0
> drmOpenDevice: open result is 7, (OK)
> drmGetBusid returned ''
> (II) SIS(0): [drm] loaded kernel module for "sis" driver
> (II) SIS(0): [drm] created "sis" driver at busid "PCI:1:0:0"
> (II) SIS(0): [drm] added 8192 byte SAREA at 0xc88dd000
> (II) SIS(0): [drm] mapped SAREA 0xc88dd000 to 0x40012000
> (II) SIS(0): [drm] framebuffer handle = 0xd0000000
> (II) SIS(0): [drm] added 1 reserved context for kernel
> (II) SIS(0): [drm] Registers = 0xdc000000
> (II) SIS(0): [drm] drmAgpEnabled succeeded
> (II) SIS(0): [drm] failure adding irq 0 handler, stereo disabled
> (II) SIS(0): [dri] visual configs initialized.
> (II) SIS(0): Frame Buffer From (0,0) To (1024,3070)
> (II) SIS(0): Using XFree86 Acceleration Architecture (XAA)
> Screen to screen bit blits
> Solid filled rectangles
> 8x8 mono pattern filled rectangles
> Indirect CPU to Screen color expansion
> Solid Lines
> Dashed Lines
> Offscreen Pixmaps
> Setting up tile and stipple cache:
> 32 128x128 slots
> 10 256x256 slots
> 4 512x512 slots
> (==) SIS(0): Backing store disabled
> (==) SIS(0): Silken mouse enabled
> (**) Option "dpms"
> (**) SIS(0): DPMS enabled
> (II) SIS(0): Using SiS300/310/325 series HW Xv
> (II) SIS(0): X context handle = 0x00000001
> (II) SIS(0): [drm] installed DRM signal handler
> (II) SIS(0): [DRI] installation complete
> (II) SIS(0): Direct rendering enabled
> (II) Setting vga for screen 0.
> (II) Initializing built-in extension MIT-SHM
> (II) Initializing built-in extension XInputExtension
> (II) Initializing built-in extension XTEST
> (II) Initializing built-in extension XKEYBOARD
> (II) Initializing built-in extension LBX
> (II) Initializing built-in extension XC-APPGROUP
> (II) Initializing built-in extension SECURITY
> (II) Initializing built-in extension XINERAMA
> (II) Initializing built-in extension XFree86-Bigfont
> (II) Initializing built-in extension RENDER
> (II) Keyboard "Keyboard1" handled by legacy driver
> (**) Option "Protocol" "PS/2"
> (**) Mouse1: Protocol: "PS/2"
> (**) Option "CorePointer"
> (**) Mouse1: Core Pointer
> (**) Option "Device" "/dev/psaux"
> (**) Option "Emulate3Buttons"
> (**) Option "Emulate3Timeout" "50"
> (**) Mouse1: Emulate3Buttons, Emulate3Timeout: 50
> (==) Mouse1: Buttons: 3
> (II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE)
> (II) Open APM successful
> (II) SIS(0): VBFlags=0x20080000
> (--) SIS(0): Before: CR30=0x00, CR31=0x60, CR32=0x20, CR33=0x02
> (II) SIS(0): After: CR30=0x00, CR31=0x64, CR33=0x04
> (II) SIS(0): Setting mode 0x64
> (--) SIS(0): (init: VBType=0x0000, VBInfo=0x0000)