Occasional crash with NM2200 (HP Omnibook 4150)
Diego SANTA CRUZ <[email protected]> 12 Apr 2002 17:47:03 +0200
| Newsgroups | gmane.comp.xfree86.neomagic |
|---|---|
| Message-ID | <[email protected]> |
Hi there, I have an HP Omnibook 4150 laptop with the nm2200 graphics chipset. First of all thanks to all the people that have contributed to this driver... your work is very much appreciated! In general the X server works OK, but I have some problems: 1. Switching resolutions (with Alt+Ctrl+KP_plus/KP_minus) often (but not always) locks the machine hard (not even a response to the Alt+SysRq key on linux). 2. Sometimes (quite rarely) the X server deadlocks taking 90-100% of CPU and I have to reboot the machine. I think it is related to scrolling and/or popup menus. 3. I often see the "(II) NEOMAGIC(0): Not programming shadow registers" message. Is this an indication of some problem? I have been looking on the list archives but I've seen no clear answer to these problems. Are there any options that cure these problems? I'm currently using XFree 4.2.0-6.52 (RedHat's) on a RedHat Linux 7.2 installation. I attach my config and X log. I would also like to know if there is a way to switch between internal and external screen without restarting the X server or using the Fn+F6 key combo (i.e. some command line utility that signals the X server to switch). Thanks in advance, Diego -- ------------------------------------------------------- Diego Santa Cruz PhD. student Publications available at http://ltswww.epfl.ch/~dsanta Signal Processing Institute (ITS) -- formerly LTS Swiss Federal Institute of Technology (EPFL) EPFL - STI - ITS, CH-1015 Lausanne, Switzerland E-mail: [email protected] Phone: +41 - 21 - 693 26 57 Fax: +41 - 21 - 693 76 00 -------------------------------------------------------
XFree86.0.log
(text/plain, 24 KB)
XFree86 Version 4.2.0 (Unofficial Custom Build: 4.2.0-6.52) / X Window System
(protocol Version 11, revision 0, vendor release 6600)
Release Date: 23 January 2002
If the server is older than 6-12 months, or if your card is
newer than the above date, look for a newer version before
reporting problems. (See http://www.XFree86.Org/)
Build Operating System: Linux 2.4.17-0.13smp i686 [ELF]
Build Host: daffy.perf.redhat.com
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Fri Apr 12 16:08:45 2002
(==) Using config file: "/etc/X11/XF86Config-4"
(==) ServerLayout "Omnibook4150"
(**) |-->Screen "monitor" (0)
(**) | |-->Monitor "SGI-GDM20E21"
(**) | |-->Device "NeoMagic 256 (laptop/notebook)"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) Option "XkbRules" "xfree86"
(**) XKB: rules: "xfree86"
(**) Option "XkbModel" "pc101"
(**) XKB: model: "pc101"
(**) Option "XkbLayout" "en_US"
(**) XKB: layout: "en_US"
(==) Keyboard: CustomKeycode disabled
(**) FontPath set to "unix/:7100,/usr/lib/xemacs/xemacs-packages/etc/x-symbol/pcf/"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(--) using VT number 7
(II) Open APM successful
(II) Module ABI versions:
XFree86 ANSI C Emulation: 0.1
XFree86 Video Driver: 0.5
XFree86 XInput driver : 0.3
XFree86 Server Extension : 0.1
XFree86 Font Renderer : 0.3
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.5
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x8001013c, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,7190 card 0000,0000 rev 02 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 8086,7191 card 0000,0000 rev 02 class 06,04,00 hdr 01
(II) PCI: 00:04:0: chip 104c,ac17 card 4000,0000 rev 02 class 06,07,00 hdr 82
(II) PCI: 00:04:1: chip 104c,ac17 card 4800,0000 rev 02 class 06,07,00 hdr 82
(II) PCI: 00:07:0: chip 8086,7110 card 0000,0000 rev 02 class 06,80,00 hdr 80
(II) PCI: 00:07:1: chip 8086,7111 card 0000,0000 rev 01 class 01,01,80 hdr 00
(II) PCI: 00:07:2: chip 8086,7112 card 0000,0000 rev 01 class 0c,03,00 hdr 00
(II) PCI: 00:07:3: chip 8086,7113 card 0000,0000 rev 02 class 06,80,00 hdr 00
(II) PCI: 01:00:0: chip 10c8,0005 card 103c,0007 rev 20 class 03,00,00 hdr 80
(II) PCI: 01:00:1: chip 10c8,8005 card 103c,0007 rev 20 class 04,01,00 hdr 80
(II) PCI: End of PCI scan
(II) LoadModule: "scanpci"
(II) Loading /usr/X11R6/lib/modules/libscanpci.a
(II) Module scanpci: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.5
(II) UnloadModule: "scanpci"
(II) Unloading /usr/X11R6/lib/modules/libscanpci.a
(II) Host-to-PCI bridge:
(II) PCI-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (-1,0,0), BCTRL: 0x08 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x8c (VGA_EN is set)
(II) Bus 1 I/O range:
(II) Bus 1 non-prefetchable memory range:
[0] -1 0xfe700000 - 0xfecfffff (0x600000) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0xfd000000 - 0xfe3fffff (0x1400000) MX[B]
(--) PCI:*(1:0:0) Neomagic NM2200 rev 32, Mem @ 0xfd000000/24, 0xfe800000/22, 0xfec00000/20
(II) Addressable bus resource ranges are
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0x00000000 - 0x000000ff (0x100) IX[B]
(II) Active PCI resource ranges:
[0] -1 0xfe700000 - 0xfe7fffff (0x100000) MX[B]
[1] -1 0xfe000000 - 0xfe3fffff (0x400000) MX[B]
[2] -1 0xfec00000 - 0xfecfffff (0x100000) MX[B](B)
[3] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[4] -1 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[5] -1 0x0000fcc0 - 0x0000fcdf (0x20) IX[B]
[6] -1 0x0000fcf0 - 0x0000fcff (0x10) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0xfe700000 - 0xfe7fffff (0x100000) MX[B]
[1] -1 0xfe000000 - 0xfe3fffff (0x400000) MX[B]
[2] -1 0xfec00000 - 0xfecfffff (0x100000) MX[B](B)
[3] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[4] -1 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[5] -1 0x0000fcc0 - 0x0000fcdf (0x20) IX[B]
[6] -1 0x0000fcf0 - 0x0000fcff (0x10) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0xfe700000 - 0xfe7fffff (0x100000) MX[B]
[6] -1 0xfe000000 - 0xfe3fffff (0x400000) MX[B]
[7] -1 0xfec00000 - 0xfecfffff (0x100000) MX[B](B)
[8] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[9] -1 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[10] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[11] -1 0x00000000 - 0x000000ff (0x100) IX[B]
[12] -1 0x0000fcc0 - 0x0000fcdf (0x20) IX[B]
[13] -1 0x0000fcf0 - 0x0000fcff (0x10) IX[B]
(II) LoadModule: "GLcore"
(II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) Module GLcore: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.1
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension FontCache
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) LoadModule: "fbdevhw"
(II) Loading /usr/X11R6/lib/modules/linux/libfbdevhw.a
(II) Module fbdevhw: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 0.0.2
ABI class: XFree86 Video Driver, version 0.5
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.a
(II) Module glx: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.1
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Reloading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/X11R6/lib/modules/extensions/librecord.a
(II) Module record: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.13.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension RECORD
(II) LoadModule: "neomagic"
(II) Loading /usr/X11R6/lib/modules/drivers/neomagic_drv.o
(II) Module neomagic: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.5
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
Module class: XFree86 XInput Driver
ABI class: XFree86 XInput driver, version 0.3
(II) NEOMAGIC: Driver for Neomagic chipsets: neo2070, neo2090, neo2093,
neo2097, neo2160, neo2200, neo2230, neo2360, neo2380
(II) Primary Device is: PCI 01:00:0
(--) Assigning device section with no busID to primary device
(--) Chipset neo2200 found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0xfe700000 - 0xfe7fffff (0x100000) MX[B]
[6] -1 0xfe000000 - 0xfe3fffff (0x400000) MX[B]
[7] -1 0xfec00000 - 0xfecfffff (0x100000) MX[B](B)
[8] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[9] -1 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[10] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[11] -1 0x00000000 - 0x000000ff (0x100) IX[B]
[12] -1 0x0000fcc0 - 0x0000fcdf (0x20) IX[B]
[13] -1 0x0000fcf0 - 0x0000fcff (0x10) IX[B]
(II) resource ranges after probing:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0xfe700000 - 0xfe7fffff (0x100000) MX[B]
[6] -1 0xfe000000 - 0xfe3fffff (0x400000) MX[B]
[7] -1 0xfec00000 - 0xfecfffff (0x100000) MX[B](B)
[8] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[9] -1 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[10] 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[11] 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[12] 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[13] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[14] -1 0x00000000 - 0x000000ff (0x100) IX[B]
[15] -1 0x0000fcc0 - 0x0000fcdf (0x20) IX[B]
[16] -1 0x0000fcf0 - 0x0000fcff (0x10) IX[B]
[17] 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[18] 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.a
(II) Module vgahw: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.5
(II) NEOMAGIC(0): Chipset is a MagicMedia 256AV (NM2200)
(II) NEOMAGIC(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(--) NEOMAGIC(0): Panel is a 1024x768 color TFT display
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.5
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.5
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/X11R6/lib/modules/linux/libint10.a
(II) Module int10: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.5
(II) NEOMAGIC(0): initializing int10
(II) NEOMAGIC(0): Primary V_BIOS segment is: 0xc000
(II) NEOMAGIC(0): VESA BIOS detected
(II) NEOMAGIC(0): VESA VBE Version 2.0
(II) NEOMAGIC(0): VESA VBE Total Mem: 2496 kB
(II) NEOMAGIC(0): VESA VBE OEM: MagicGraph 256 AV 48K
(II) NEOMAGIC(0): VESA VBE OEM Software Rev: 1.7
(II) NEOMAGIC(0): VESA VBE OEM Vendor: NeoMagic
(II) NEOMAGIC(0): VESA VBE OEM Product: MagicMedia 256 AV
(II) NEOMAGIC(0): VESA VBE OEM Product Rev: 01.0
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) NEOMAGIC(0): VESA VBE DDC supported
(II) NEOMAGIC(0): VESA VBE DDC Level 2
(II) NEOMAGIC(0): VESA VBE DDC transfer in appr. 1 sec.
(II) NEOMAGIC(0): VESA VBE DDC read successfully
(II) NEOMAGIC(0): Manufacturer: SGX Model: 100 Serial#: 2001892
(II) NEOMAGIC(0): Year: 1996 Week: 10
(II) NEOMAGIC(0): EDID Version: 1.0
(II) NEOMAGIC(0): Analog Display Input, Input Voltage Level: 0.714/0.286 V
(II) NEOMAGIC(0): Sync: Separate Composite SyncOnGreen
(II) NEOMAGIC(0): Max H-Image Size [cm]: horiz.: 38 vert.: 29
(II) NEOMAGIC(0): Gamma: 2.60
(II) NEOMAGIC(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) NEOMAGIC(0): redX: 0.625 redY: 0.340 greenX: 0.280 greenY: 0.595
(II) NEOMAGIC(0): blueX: 0.155 blueY: 0.070 whiteX: 0.283 whiteY: 0.298
(II) NEOMAGIC(0): Supported VESA Video Modes:
(II) NEOMAGIC(0): 1024x768@75Hz
(II) NEOMAGIC(0): 1280x1024@75Hz
(II) NEOMAGIC(0): Manufacturer's mask: 0
(II) NEOMAGIC(0): Supported additional Video Mode:
(II) NEOMAGIC(0): clock: 129.2 MHz Image Size: 350 x 280 mm
(II) NEOMAGIC(0): h_active: 1280 h_sync: 1312 h_sync_end 1452 h_blank_end 1680 h_border: 0
(II) NEOMAGIC(0): v_active: 1024 v_sync: 1027 v_sync_end 1030 v_blanking: 1065 v_border: 0
(II) NEOMAGIC(0): Supported additional Video Mode:
(II) NEOMAGIC(0): clock: 140.2 MHz Image Size: 350 x 280 mm
(II) NEOMAGIC(0): h_active: 1280 h_sync: 1312 h_sync_end 1488 h_blank_end 1712 h_border: 0
(II) NEOMAGIC(0): v_active: 1024 v_sync: 1027 v_sync_end 1030 v_blanking: 1079 v_border: 0
(II) NEOMAGIC(0): Supported additional Video Mode:
(II) NEOMAGIC(0): clock: 156.2 MHz Image Size: 373 x 280 mm
(II) NEOMAGIC(0): h_active: 1600 h_sync: 1644 h_sync_end 1764 h_blank_end 2088 h_border: 0
(II) NEOMAGIC(0): v_active: 1200 v_sync: 1205 v_sync_end 1211 v_blanking: 1250 v_border: 0
(II) NEOMAGIC(0): Supported additional Video Mode:
(II) NEOMAGIC(0): clock: 107.2 MHz Image Size: 350 x 280 mm
(II) NEOMAGIC(0): h_active: 1280 h_sync: 1320 h_sync_end 1440 h_blank_end 1680 h_border: 0
(II) NEOMAGIC(0): v_active: 492 v_sync: 495 v_sync_end 498 v_blanking: 532 v_border: 0
(**) NEOMAGIC(0): Depth 16, (--) framebuffer bpp 16
(==) NEOMAGIC(0): RGB weight 565
(==) NEOMAGIC(0): Default visual is TrueColor
(==) NEOMAGIC(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NEOMAGIC(0): Option "externDisp"
(**) NEOMAGIC(0): Option "LcdCenter"
(**) NEOMAGIC(0): Option "NoStretch"
(**) NEOMAGIC(0): External CRT only display mode
(**) NEOMAGIC(0): Low resolution video modes are not stretched
(**) NEOMAGIC(0): Video modes are centered on the display
(==) NEOMAGIC(0): using linear mode
(**) NEOMAGIC(0): using PCI Burst mode
(**) NEOMAGIC(0): Option StrangeLockups set: disabling some acceleration
(--) NEOMAGIC(0): FB base address is set at 0xFD000000.
(--) NEOMAGIC(0): MMIO base address is set at 0xFE800000.
(**) NEOMAGIC(0): VideoRAM: 2304 kByte
(--) NEOMAGIC(0): Max Clock: 110000 kHz
(II) NEOMAGIC(0): SGI-GDM20E21: Using hsync range of 30.00-70.00 kHz
(II) NEOMAGIC(0): SGI-GDM20E21: Using vrefresh range of 60.00-85.00 Hz
(II) NEOMAGIC(0): Clock range: 11.00 to 110.00 MHz
(II) NEOMAGIC(0): Not using mode "1400x1050" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using mode "1400x1050" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using mode "1400x1050" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using mode "1400x1050" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "800x600" (vrefresh out of range)
(II) NEOMAGIC(0): Not using default mode "400x300" (vrefresh out of range)
(II) NEOMAGIC(0): Not using default mode "1024x768" (vrefresh out of range)
(II) NEOMAGIC(0): Not using default mode "512x384" (vrefresh out of range)
(II) NEOMAGIC(0): Not using default mode "1280x960" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "1280x960" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "640x480" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "1280x1024" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "1280x1024" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "640x512" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "1280x1024" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "640x512" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "1600x1200" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "800x600" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "1600x1200" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "800x600" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "1600x1200" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "800x600" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "1600x1200" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "800x600" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "1600x1200" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) NEOMAGIC(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "896x672" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) NEOMAGIC(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "928x696" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) NEOMAGIC(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) NEOMAGIC(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) NEOMAGIC(0): Not using default mode "1152x864" (bad mode clock/interlace/doublescan)
(II) NEOMAGIC(0): Not using default mode "576x432" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "700x525" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "700x525" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "700x525" (hsync out of range)
(II) NEOMAGIC(0): Not using default mode "1600x1024" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "1920x1200" (insufficient memory for mode)
(II) NEOMAGIC(0): Not using default mode "960x600" (bad mode clock/interlace/doublescan)
(--) NEOMAGIC(0): Virtual size is 1024x768 (pitch 1024)
(**) NEOMAGIC(0): Default mode "1024x768": 94.5 MHz, 68.7 kHz, 85.0 Hz
(II) NEOMAGIC(0): Modeline "1024x768" 94.50 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
(**) NEOMAGIC(0): Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz
(II) NEOMAGIC(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync
(**) NEOMAGIC(0): Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz
(II) NEOMAGIC(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync
(**) NEOMAGIC(0): Display dimensions: (369, 279) mm
(WW) NEOMAGIC(0): Probed monitor is 380x290 mm, using Displaysize 369x279 mm
(**) NEOMAGIC(0): DPI set to (70, 69)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 ANSI C Emulation, version 0.1
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.5
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.5
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0xfec00000 - 0xfecfffff (0x100000) MX[B]
[1] 0 0xfe800000 - 0xfebfffff (0x400000) MX[B]
[2] 0 0xfd000000 - 0xfdffffff (0x1000000) MX[B]
[3] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[4] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[5] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[6] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[7] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[8] -1 0xfe700000 - 0xfe7fffff (0x100000) MX[B]
[9] -1 0xfe000000 - 0xfe3fffff (0x400000) MX[B]
[10] -1 0xfec00000 - 0xfecfffff (0x100000) MX[B](B)
[11] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[12] -1 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[13] 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[14] 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[15] 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[16] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[17] -1 0x00000000 - 0x000000ff (0x100) IX[B]
[18] -1 0x0000fcc0 - 0x0000fcdf (0x20) IX[B]
[19] -1 0x0000fcf0 - 0x0000fcff (0x10) IX[B]
[20] 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[21] 0 0x000003c0 - 0x000003df (0x20) IS[B]
(==) NEOMAGIC(0): Write-combining range (0xfd000000,0x400000)
(II) NEOMAGIC(0): Not programming shadow registers
(II) NEOMAGIC(0): Using linear framebuffer at: 0xFD000000
(--) NEOMAGIC(0): 786432 bytes off-screen memory available
(II) NEOMAGIC(0): Using H/W Cursor.
(II) NEOMAGIC(0): Using 256 scanlines of offscreen memory for pixmap caching
(II) NEOMAGIC(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
Solid Horizontal and Vertical Lines
Offscreen Pixmaps
Setting up tile and stipple cache:
16 128x128 slots
(II) NEOMAGIC(0): Acceleration Initialized
(==) NEOMAGIC(0): Backing store disabled
(==) NEOMAGIC(0): Silken mouse enabled
(**) Option "dpms"
(**) NEOMAGIC(0): DPMS enabled
(II) Setting vga for screen 0.
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(**) Option "Protocol" "PS/2"
(**) Mouse0: Protocol: "PS/2"
(**) Option "CorePointer"
(**) Mouse0: Core Pointer
(**) Option "Device" "/dev/psaux"
(**) Option "Emulate3Buttons" "yes"
(**) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5"
(**) Mouse0: ZAxisMapping: buttons 4 and 5
(**) Mouse0: Buttons: 5
(II) Keyboard "Keyboard0" handled by legacy driver
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(**) Option "Device" "/dev/psaux"
SetKbdSettings - type: 0 rate: 50 delay: 500 snumlk: 0
SetKbdSettings - Succeeded
GetModeLine - scrn: 0 clock: 94500
GetModeLine - hdsp: 1024 hbeg: 1072 hend: 1168 httl: 1376
vdsp: 768 vbeg: 769 vend: 772 vttl: 808 flags: 5
(II) NEOMAGIC(0): Not programming shadow registers
(II) Open APM successful
(II) NEOMAGIC(0): Not programming shadow registers
(**) Option "Device" "/dev/psaux"
(WW) System time not monotonic!
XF86Config-4
(text/plain, 8.2 KB)
# File generated by anaconda.
Section "ServerLayout"
Identifier "Omnibook4150"
Screen 0 "monitor" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "ServerFlags"
# DSC: unfortunately the neomagic driver crashes the machine
# if we change the video mode :-( So disallow the change
#Option "DontZoom"
#Option "DisableVidModeExtension"
EndSection
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.
FontPath "unix/:7100"
# Used for the XSymbol package of XEmacs (must be in X server fontpath, not
# fontserver's one)
FontPath "/usr/lib/xemacs/xemacs-packages/etc/x-symbol/pcf/"
EndSection
Section "Module"
Load "GLcore"
Load "dbe"
Load "extmod"
Load "fbdevhw"
# Load "pex5"
# Load "dri"
Load "glx"
Load "record"
# Load "xie"
# DSC add all font modules (freetype and xtt can not be mixed)
# Load "type1"
# Load "freetype"
# Load "xtt"
# Load "speedo"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
# Option "AutoRepeat" "500 5"
# when using XQUEUE, comment out the above line, and uncomment the
# following line
# Option "Protocol" "Xqueue"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# Option "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:nocaps"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc101"
# Option "XkbModel" "pc105"
Option "XkbLayout" "en_US"
# Option "XkbLayout" "us"
#Option "XkbVariant" ""
#Option "XkbOptions" ""
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "PS/2"
Option "Device" "/dev/psaux"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "yes"
EndSection
Section "Monitor"
Identifier "LCD 1024x768"
VendorName "HP"
ModelName "Omnibook 4150"
HorizSync 30.0-85.0
VertRefresh 48.0-160.0
DisplaySize 287 215
EndSection
# SGI's GDM 20E21 monitor has an horiz freq. range of 48-160, but the
# computer's interface has the range 60-85 (as from the specs)
Section "Monitor"
Identifier "SGI-GDM20E21"
VendorName "SGI"
ModelName "GDM 20E21"
# HorizSync 30.0-96.0
HorizSync 30.0-70.0
# VertRefresh 48.0-160.0
VertRefresh 60-85
DisplaySize 369 279
Option "dpms"
# -- 1400x1050 --
# 1400x1050 @ 60Hz, 65.8 kHz hsync
Modeline "1400x1050" 129 1400 1464 1656 1960
1050 1051 1054 1100 +HSync +VSync
# 1400x1050 @ 70Hz, 76.8 kHz hsync
Modeline "1400x1050" 151 1400 1464 1656 1960
1050 1051 1054 1100 +HSync +VSync
# 1400x1050 @ 75Hz, 82.3 kHz hsync
Modeline "1400x1050" 162 1400 1464 1656 1960
1050 1051 1054 1100 +HSync +VSync
# 1400x1050 @ 85Hz, 93.2 kHz hsync
Modeline "1400x1050" 184 1400 1464 1656 1960
1050 1051 1054 1100 +HSync +VSync
EndSection
Section "Device"
# Option "Rotate"
# Option "pciBurst"
# Option "ShadowFB"
Option "NoStretch"
Option "LcdCenter"
# Option "externDisp"
# Option "internDisp"
# Option "noMMIO"
# Option "SWcursor"
# Option "NoAccel"
# Option "NoLinear"
# Option "XaaNoScanlineImageWriteRect"
# Option "XaaNoScanlineCPUToScreenColorExpandFill"
# Option "XaaNoSolidFillRect"
Identifier "NeoMagic 256 (laptop/notebook)"
Driver "neomagic"
VendorName "NeoMagic 256 (laptop/notebook)"
BoardName "NeoMagic 256 (laptop/notebook)"
# DSC: don't use all RAM, since upper part is
# shared with audio buffers. We use just enough for
# 24 bit 1024x768, leaving 256 kB for audio buffers
VideoRam 2304
#BusID
EndSection
# Screen that starts in whatever display the BIOS says
# (normally external if there is a monitor and LCD otherwise)
Section "Screen"
Identifier "auto"
Device "NeoMagic 256 (laptop/notebook)"
Monitor "SGI-GDM20E21"
DefaultDepth 16
Subsection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480" "1280x1024"
# Modes "1024x768"
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
# Modes "1024x768"
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
# Modes "1024x768"
EndSubsection
EndSection
# Screen that starts in both, LCD and external monitor mode.
Section "Screen"
Identifier "both"
Device "NeoMagic 256 (laptop/notebook)"
Monitor "SGI-GDM20E21"
DefaultDepth 16
Option "internDisp"
Option "externDisp"
Subsection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480" "1280x1024"
# Modes "1024x768"
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
# Modes "1024x768"
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
# Modes "1024x768"
EndSubsection
EndSection
# Screen that starts automatically in LCD setting
Section "Screen"
Identifier "lcd"
Device "NeoMagic 256 (laptop/notebook)"
Monitor "LCD 1024x768"
DefaultDepth 16
Option "internDisp"
Subsection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480" "1280x1024"
# Modes "1024x768"
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
# Modes "1024x768"
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
# Modes "1024x768"
EndSubsection
EndSection
# Screen that starts automatically in external monitor setting
Section "Screen"
Identifier "monitor"
Device "NeoMagic 256 (laptop/notebook)"
Monitor "SGI-GDM20E21"
DefaultDepth 16
Option "externDisp"
Subsection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480" "1280x1024"
# Modes "1024x768"
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
# Modes "1024x768"
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
# Modes "1024x768"
EndSubsection
EndSection
Section "DRI"
Mode 0666
EndSection