Re: VECTOR: SW monitor prob...

Thad,
you were right, after i had rebuilt the HV section and recapped the 
deflection pcb i still had the "LARGE" problem but it was in focus, i had 
just bought myself a spare SW pcb set (so i could put my ESB kit on it) and 
tried this in the cab, and Bingo ! it was perfect.....
So the fault, was the game boards all along, the thing is, what could be 
causing this ?

Many thanx as always for all the advice,


Pinx

oh and Phil, thanx for the spare pcb set :)


----- Original Message ----- 
From: "Thad Seeberger" <[email protected]>
To: <[email protected]>
Sent: Thursday, April 07, 2005 2:19 PM
Subject: Re: VECTOR: SW monitor prob...


> OK, I dont believe you have a HV problem but a XY drive problem. To me if 
> it was blooming from HV going low you would loose focus. I would check the 
> XY outputs and see if there is a bad connection on the edge connector such 
> as the ground. Also measure the voltages on the board (game board)for the 
> +/-15 VDC and the XY outputs. I guess it could still be the monitor but 
> more than likely something on the deflection board not the HV. I would 
> also measure the input voltage AC to monitor and the DC voltage of the 
> deflection regulators, I dont remember what it is, maybe +/45 VDC or 
> something, if that was amuck could cause your problem.
>
> Thad
>
> Pinx wrote:
>
>> It is in focus,
>> just a really large image so some of the image is off the screen....
>>
>>
>> Pinx
>>
>> ----- Original Message ----- From: "Thad Seeberger" <[email protected]>
>> To: <[email protected]>
>> Sent: Wednesday, April 06, 2005 9:15 PM
>> Subject: Re: VECTOR: SW monitor prob...
>>
>>
>>> Is the image focused? if its focused (DURING BLOOM) you have XY drive 
>>> problem. Check the focus block you could have something leaky make sure 
>>> there is no corona. When measuring the HV is it ok while blooming 
>>> (loaded) or with no drive. If its fluctuating there is a problem with 
>>> the regulator. If its bllooming because of HV drop you will loose focus 
>>> also since the focus is just a divider of the HV.  Make sure there is no 
>>> DC offset on XY input. I havent been following this thread so you might 
>>> have already checked but I cant think of what else would make it bloom 
>>> other than a CRT with low emision, is the heater got 6.3V on it? and all 
>>> the connections good on the socket such as cathode, heater, focus etc. 
>>> It definately sounds like a regulation problem. I would buy the 
>>> repacement HV kit from arcadeshop. I've installed a few of them and I 
>>> think they are well worth it.
>>>
>>> Thad
>>>
>>>
>>> Pinx wrote:
>>>
>>>> Right,
>>>>  now i am really baffled, not only have i re-capped it but now i have 
>>>> replaced the transistors at Q901, Q902, Q903, Q904 and replaced the 
>>>> Zeners at ZD900, ZD901, ZD902. I have also replaced the resistors at 
>>>> R912, R920, R922, R925.
>>>>  I put my HV probe in with the monitor switched on and set the HV to 
>>>> 19500V and still the image on the screen is massive !!!
>>>> Starting to pull my hair out now (not that ive got much) any more 
>>>> idea's anyone ? Should the HV be measured with the game pcb unplugged ?
>>>>  Pinx
>>>>     ----- Original Message -----
>>>>     *From:* Pinx <mailto:[email protected]>
>>>>     *To:* [email protected] <mailto:[email protected]>
>>>>     *Sent:* Friday, April 01, 2005 7:36 PM
>>>>     *Subject:* VECTOR: SW monitor prob...
>>>>
>>>>     Hi guys,
>>>>      just recently the WG in my SW has developed a problem where the
>>>>     image is massive, so you cant see it all on the screen. I have
>>>>     been told this is "blooming" and so i have just re-capped the HV
>>>>     section, but i still have the problem. Is there anything else on
>>>>     the HV board i should replace to cure this problem ?
>>>>      TIA
>>>>      Pinx
>>>>
>>>
>>> ---------------------------------------------------------------------------
>>>
>>> ** Unsubscribe, subscribe, or view the archives at 
>>> http://www.vectorlist.org
>>> ** Please direct other questions, comments, or problems to 
>>> [email protected]
>>>
>>
>> ---------------------------------------------------------------------------
>>
>> ** Unsubscribe, subscribe, or view the archives at 
>> http://www.vectorlist.org
>> ** Please direct other questions, comments, or problems to 
>> [email protected]
>
>
> ---------------------------------------------------------------------------
> ** Unsubscribe, subscribe, or view the archives at 
> http://www.vectorlist.org
> ** Please direct other questions, comments, or problems to 
> [email protected]
>