[dhcwg] Re: Intdir telechat review of draft-ietf-dhc-addr-no tification-11
CARLOS JESUS BERNARDOS CANO <[email protected]>
| Newsgroups | gmane.ietf.dhc |
|---|---|
| Message-ID | <CALypLp_+pSHye07wToKGwciO9C5cY6cwX1M=zGSrpg2Mc3Jsvg@mail.gmail.com> |
Hi Jen, Thanks for the updates. Some quick comments inline below. On Tue, May 14, 2024 at 8:48 AM Jen Linkova <[email protected]> wrote: > Hi Carlos, > > On Fri, May 10, 2024 at 7:51 AM Carlos Jesús Bernardos via Datatracker > <[email protected]> wrote: > > Based on my review, if I was on the IESG I would ballot this document as > YES. > > Thank you! ;) > > > - At the end of section 1, it is mentioned that the mechanism described > in the > > document provides parity with IPv4, by allowing a device to inform the > DHCPv6 > > server about a self-configured or statically configured address. > Apologies for > > my ignorance on this in advance, but, is there a mechanism in IPv4 to do > so for > > statically configured addresses? If so, I think adding a reference would > be > > useful. If not, maybe the text can be rewritten a bit, as I would find > it a bit > > unclear. > > We've just submitted -12 which now says: > "This operational practice relies on the DHCP server knowing the IP > address assignments. This works quite well for IPv4 addresses, as most > addresses are either assigned by DHCP [RFC2131] or statically > configured by the network operator. For IPv6, however, this practice > is much harder to implement, as devices often self-configure IPv6 > addresses via SLAAC [RFC4862]. > > This document provides a mechanism for a device to inform the DHCPv6 > server that the device has a self-configured IPv6 address (or has a > statically configured address), and thus provides parity with IPv4, by > making DHCPv6 infrastructure aware of self-assigned IPv6 addresses." > > I hope it's more clear now, pls let us know if you think further > improvements are needed. > [Carlos] Fine with me, thanks! > > > - It is mentioned that the client MUST include the Client Identifier > option in > > the ADDRESS-REG-INFORM messages. I think this might deserve some text > regarding > > how this might imply (or not) a potential privacy issue for hosts > implementing > > some kind of MAC address randomization and rotation of IPv6 self-assigned > > addresses, as an observer could easily track the addresses being used > and match > > those to the same device. > > We don’t think this is a concern, because on-link attackers do not > need to use the client identifier to match self-assigned addresses to > devices, they can use the MAC address for that purpose. > Privacy-sensitive clients that randomize their MAC addresses should > obviously randomize their DHCPv6 Client Identifiers too. We’re not > sure this document is the right place to say so, though? > [Carlos] While I agree that this is not the document to specify how to use DHCPv6 Client Identifiers, I think adding notifications that can allow an on-link attacker to match a MAC-changing device with the addresses it might be using would deserve at least a reference to the documents that have tackled the privacy issues in the past (I think there is one specifically tackling the aspects of DHCPv6). > > > - It is not completely clear to me if the spec requires a client to use > the > > mechanism on ALL interfaces. I mean, can a client use it just on some > > interfaces, but not all, by having configuration policies indicating on > which > > ones to use it? As I read the document, it seems to imply that if it is > used on > > one interface, it MUST be used on all of them. > > Oh very good point, I didn't realize we are not making that part > clear. No, as the registration messame must be sent from the address > being registered (section 4.2 does say that), and the registration > support is network-specific, the client should (must) enable this on > per-interface basis. > We have added the following text to Section 4.4: > "A client with multiple interfaces MUST discover address registration > support for each interface independently. The client MUST NOT send > address registration messages on a given interface unless the client > has discovered that the interface is connected to a network which > supports address registration." > [Carlos] Great, thanks! > > > > - Minor nit (or maybe just nothing at it is just that I’m not a native > English > > speaker): “to specify the address to being registered” -> I guess the > “to” > > should be removed. > > Yeah, a typo, fixed! > [Carlos] Thanks! > > -- > Cheers, Jen Linkova > _______________________________________________ dhcwg mailing list -- [email protected] To unsubscribe send an email to [email protected]