RE: Augmenting MAU-MIB - was: RE: EFM MIB Internet-Drafts,WG Meetings

In order for this change to be performed, we need to add the following to the Charter:

'The MAU MIB will be revised to include support for MAU types and jack types for Ethernet First Mile and for 10 GB Ethernet copper'. 

Also, the deliverables need to include the MAU MIB revisions. I suggest time frames similar with the EFM MIBs. 

Note the 'neutral' reference to copper 10G. If 10GBASE-T is late at dinner and cannot provide a normative reference by the time the MAU MIB is in last approval phases, we can take it out, so that the rest of the work is not hold up. 

If there are no abjections in the next week, I will forward officially this proposal to Bert. 

Regards,

Dan


> -----Original Message-----
> From: John Flick [mailto:[email protected]]
> Sent: 03 November, 2003 10:57 PM
> To: C. M. Heard
> Cc: Hub Mib
> Subject: Re: Augmenting MAU-MIB - was: RE: [Hubmib] EFM MIB 
> Internet-Drafts,WG Meetings
> 
> 
> Mike,
> 
> I do think it is appropriate to open up MAU MIB to add the types for
> EFM and for 10GBASE-CX4 and 10GBASE-T.  In addition to the changes
> you noted for 10GBASE-CX4, we would need to add a new jack to the
> JackType TC = CX4 uses an IB4X connector.  One caution here is that
> 10GBASE-T is alot less far along than the others, and I would not
> want to hold up a rev of this document for a stable 10GBASE-T
> specification.
> 
> John
> 
> "C. M. Heard" wrote:
> > 
> > Colleagues,
> > 
> > I forgot to metion this earlier, but it occurs to me that the EFM
> > effort is not the only one that will define new standard MAU types.
> > 10GBASE-CX4 and 10GBASE-T will also do that.  So if the MAU MIB is
> > opened up for modification to add new MAU types the WG may wish to
> > consider adding support for 10GBASE-CX4 and 10GBASE-T media types.
> > Attached below is an earlier message of mine on this subject.
> > 
> > Mike
> > 
> >   
> --------------------------------------------------------------
> --------------------------------------
> > 
> > Subject: [Hubmib] 10GBASE-CX4 and 10GBASE-T
> > Date: Tue, 14 Jan 2003 12:03:41 -0800 (PST)
> > From: "C. M. Heard" <[email protected]>
> > To: Hub MIB <[email protected]>
> > 
> > Hub MIB folks,
> > 
> > For those who aren't already aware, I'd like to bring your
> > attention to the fact that there are two IEEE study groups
> > at work on new PMDs for 10 Gb/s Ethernet.  The 10GBASE-CX4
> > group is working on a 15 m shielded copper solution that
> > will use the same PCS as does 10GBASE-LX4.  The 10GBASE-T
> > group is working on a 100 m UTP solution.  Those who are
> > interested can find more information on the 802.3 web site
> > http://grouper.ieee.org/groups/802/3/
> > 
> > The 10GBASE-CX4 effort has, I believe, the much shorter
> > timeline, and it appears that the impact on our documents
> > will be minimal.  In fact as far as I can tell, the only
> > document that will be affected is the MAU-MIB document,
> > and the changes to it will be confined to the following
> > additions:
> > 
> >        [ ... ]
> > 
> >        dot3MauType10GigBaseCX4 OBJECT-IDENTITY
> >            STATUS      current
> >            DESCRIPTION "X fiber over copper (per 802.3 section
> >                        54)"
> >            ::= { dot3MauType XX } -- NOTE: next unassigned 
> value is 41
> > 
> >        [ ... ]
> > 
> >        ifMauTypeListBits OBJECT-TYPE
> >            SYNTAX      BITS {
> >                [ ... ]
> >                b10GbaseCX4(XX),   -- 10GBASE-CX4  (see NOTE above)
> >                [ ... ]
> >            }
> >        [ ... ]
> > 
> > These would mirror the proposed changes to Clause 30, which you can
> > find here:
> > 
> > 
http://grouper.ieee.org/groups/802/3/10GBCX4/public/jan03/WP2p0_cls30_annex30B.pdf
> 
> While it is probably not be appropriate to include this stuff in the
> next MAU-MIB draft that includes the 802.3ae stuff, the changes are
> small enough that they should be able to go into a maintenance update
> without affecting time-in-grade, or else when then the document
> advances Draft Standard.
> 
> The impact of 10GBASE-T is harder to gauge.
> 
> Mike Heard
> 
> _______________________________________________
> Hubmib mailing list
> [email protected]
> https://www1.ietf.org/mailman/listinfo/hubmib

_______________________________________________
Hubmib mailing list
[email protected]
https://www1.ietf.org/mailman/listinfo/hubmib