Re: EPX: "feed-orientation" attribute orphaned

ISTO-PWG Internet Printing Protocol workgroup discussion forum via ipp <[email protected]> Mon, 14 Mar 2022 18:34:49 +0000
Newsgroups	gmane.ietf.ipp
Message-ID	<[email protected]>
Ye

> On Mar 14, 2022, at 12:30 PM, ISTO-PWG Internet Printing Protocol workgroup discussion forum via ipp <[email protected]> wrote:
> 
> Signed PGP part
> Smith,
> 
> You also need to add the (obsolete) entries in the registry sections.

Yep, got that, and so you responding as you did makes me think I need to do both the attributes and the values in the IANA registry. But do I need to list the keywords in the Obsolete Values section too?

> 
> 
>> On Mar 14, 2022, at 2:09 PM, ISTO-PWG Internet Printing Protocol workgroup discussion forum via ipp <[email protected] <mailto:[email protected]>> wrote:
>> 
>> Signed PGP part
>> Quick editorial question: I have separate sections for Obsolete Attributes and Obsolete Values. The only entries I currently have in the latter are those values that are obsolete for attributes that are not obsolete. If that is fine, then I'll simply add "feed-orientation" / "feed-orientation-default" / "feed-orientation-supported" to the Obsolete Attributes section and be done?
>> 
>> 
>>> On Mar 14, 2022, at 9:44 AM, Kennedy, Smith (Wireless & IPP Standards) <[email protected]> wrote:
>>> 
>>> Hi Mike,
>>> 
>>> I will add all of those to the obsolete sections in the next draft of IPP Enterprise Printing Extensions v2.0.
>>> 
>>> Cheers,
>>> Smith
>>> ---
>>> Smith Kennedy
>>> [email protected]
>>> 
>>> 
>>>> On Mar 14, 2022, at 9:33 AM, ISTO-PWG Internet Printing Protocol workgroup discussion forum via ipp <[email protected]> wrote:
>>>> 
>>>> All,
>>>> 
>>>> I'm going through the IPP registry and CUPS sources (to make sure that everything is up-to-date and in sync) and noticed that the "feed-orientation" attribute has gone missing from the current EPX draft.  From the original PWG 5100.11:
>>>> 
>>>> 7.1 feed-orientation (type3 keyword)
>>>> 
>>>> The OPTIONAL "feed-orientation" Job Template attribute specifies the media edge which is fed into the print engine from the paper tray. Long-edge-first is the preferred method of feeding media to attain the fastest printing speed. Certain media will have adverse effects when fed from a certain direction; for instance, some labels will peel off in the paper path when fed long-edge-first, but not when fed short-edge-first. The feed orientation also may allow the job to be finished in more acceptable ways; for instance, a stationary finishing stapler may provide a preferred stapling location when the media is fed short-edge-first.
>>>> 
>>>> When this attribute is specified, the printer selects media that has already been loaded in the requested orientation. If the media is not currently loaded in the requested orientation, the job may enter the 'processing-stopped' state with a "job-state-reason" of 'resources-are-not-ready'.
>>>> 
>>>> Standard keyword values are:
>>>> 
>>>> Keyword
>>>> 
>>>> 'long-edge-first'
>>>> 
>>>> 'short-edge-first'
>>>> 
>>>> Now, if I go back through the archives then it looks like we had decided to make this attribute obsolete rather than bring it into the new-and-improved 5100.11 - mainly because feed orientation is determined by the input tray. But right now "feed-orientation" and the corresponding -default and -supported attributes are not mentioned in the obsolete section nor can they be found as current attributes...
>>>> 
>>>> ________________________
>>>> Michael Sweet
>>>> 
>>>> 
>>>> 
>>>> _______________________________________________
>>>> ipp mailing list
>>>> [email protected]
>>>> https://www.pwg.org/mailman/listinfo/ipp
>> 
>> 
>> 
> 
> ________________________
> Michael Sweet
> 
> 
> 
> 
> 
>

_______________________________________________
ipp mailing list
[email protected]
https://www.pwg.org/mailman/listinfo/ipp
signature.asc (application/pgp-signature, 833 B)