Re: Port numbers

Some ENRP messages can be sent via multicast...

On Aug 23, 2005, at 21:03 Uhr, Peter Lei wrote:

> Did I miss something-- ENRP over UDP??  I thought we were
> only doing ENRP over SCTP...
>
> --peter
>
>
> Michael Tuexen wrote:
>> Just do be sure:
>> do you want a separate port for ASAP and ENRP or not?
>> The rsplib does use two ports, I think Lyndon originally
>> requested two (or four to be precise, also two for ASAP/TLS
>> and ENRP/TLS, but we got only ASAP:
>> asap-tcp-tls    3864/tcp   asap/tls tcp port
>> asap-tcp-tls    3864/udp   asap/tls tcp port
>> )
>> but did not get the ones for ENRP.
>> So I think we need separate port for ENRP and ASAP.
>> Best regards
>> Michael
>> On Aug 23, 2005, at 14:18 Uhr, Randall Stewart wrote:
>>> Thoughts/questions..
>>>
>>> Should there NOT be a seperate ENRP port too.. I
>>> know in the original Motorola code the ENRP deamon
>>> had two seperate ports.. one to speak ASAP with
>>> clients and the other to speak ENRP to peers.
>>> I have not did a careful read of ENRP in some
>>> time... so maybe Q has edited that out.. or maybe
>>> it was never clear in the documents..
>>>
>>> If we are going back to IANA maybe we should
>>> get a set for ENRP as well, Q, any thoughts???
>>>
>>> R
>>>
>>> Ong, Lyndon wrote:
>>>
>>>> Hi Folks,
>>>> I will contact IANA about the port numbers.  Thanks for the
>>>> catch!
>>>> Lyndon -----Original Message-----
>>>> From: [email protected] [mailto:[email protected]] 
>>>> On
>>>> Behalf Of Johnson Walter-CWJ002
>>>> Sent: Tuesday, August 09, 2005 6:51 AM
>>>> To: 'Michael Tuexen'; [email protected]
>>>> Subject: RE: [Rserpool] Port numbers
>>>> http://www.iana.org/cgi-bin/usr-port-number.pl
>>>> This is the application for requesting user port numbers for udp, 
>>>> tcp,
>>>> sctp.
>>>> -----Original Message-----
>>>> From: [email protected] [mailto:[email protected]] 
>>>> On
>>>> Behalf Of Michael Tuexen
>>>> Sent: Tuesday, August 09, 2005 8:40 AM
>>>> To: [email protected]
>>>> Subject: [Rserpool] Port numbers
>>>> Dear all,
>>>> I checked http://www.iana.org/assignments/port-numbers
>>>> and found:
>>>> asap-tcp        3863/tcp   asap tcp port
>>>> asap-tcp        3863/udp   asap tcp port
>>>> #                          Lyndon Ong <[email protected]> August 2003
>>>> First of all I think the second line should read
>>>> asap-udp        3863/udp   asap udp port
>>>> and we still miss a port number for asap-sctp and enrp over UDP and
>>>> SCTP.
>>>> I'm not sure who is the right contact for this problem. Possily 
>>>> Lyndon?
>>>> Best regards
>>>> Michael
>>>> _______________________________________________
>>>> rserpool mailing list
>>>> [email protected]
>>>> https://www1.ietf.org/mailman/listinfo/rserpool
>>>> _______________________________________________
>>>> rserpool mailing list
>>>> [email protected]
>>>> https://www1.ietf.org/mailman/listinfo/rserpool
>>>> _______________________________________________
>>>> rserpool mailing list
>>>> [email protected]
>>>> https://www1.ietf.org/mailman/listinfo/rserpool
>>>
>>>
>>>
>>> -- 
>>> Randall Stewart
>>> 803-345-0369 <or> 815-342-5222(cell)
>>>
>> _______________________________________________
>> rserpool mailing list
>> [email protected]
>> https://www1.ietf.org/mailman/listinfo/rserpool
>