[ACPI-sppt] problems with an Acer Aspire 1310
Pau Aliagas <[email protected]> Wed, 15 Oct 2003 11:51:23 +0200 (CEST)
| Newsgroups | gmane.linux.acpi.support |
|---|---|
| Message-ID | <[email protected]> |
I have lots of problems with an Acer Aspire 1310 laptop that does not setup properly the IRQs, does not detect the devices, etc. I follow the "advices" when booting without parametres, so I've added: pci=noacpi pci=usepirqmask pci=biosirq It makes no difference. I've posted several times my problesm in the lkml with no success, so I'm tryinig here that seems more specific. Thanks in advance for your help. The most significant messages are: PCI: Cannot allocate resource region 0 of device 0000:00:0a.0 PCI: Via IRQ fixup for 0000:00:10.1, from 255 to 0 PCI: No IRQ known for interrupt pin D of device 0000:00:10.3. drivers/usb/core/hcd-pci.c: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.3 setup! PCI: No IRQ known for interrupt pin B of device 0000:00:10.1. drivers/usb/core/hcd-pci.c: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.1 setup! This is the relevant info, I think. If anything is needed I'm willing to provide it and test the possible solutions. $ dmesg Oct 14 19:41:36 pau kernel: Linux version 2.6.0-0.test7.1.52 ([email protected]) (gcc version 3.3.1 20030930 (Red Hat Linux 3.3.1-6)) #1 Fri Oct 10 09:40:33 EDT 2003 Oct 14 19:41:36 pau kernel: Video mode to be used for restore is f00 Oct 14 19:41:36 pau kernel: BIOS-provided physical RAM map: Oct 14 19:41:36 pau kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)Oct 14 19:41:36 pau kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) Oct 14 19:41:36 pau kernel: BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) Oct 14 19:41:36 pau kernel: BIOS-e820: 0000000000100000 - 000000002dff0000 (usable)Oct 14 19:41:36 pau kernel: BIOS-e820: 000000002dff0000 - 000000002dffffc0 (ACPI data) Oct 14 19:41:36 pau kernel: BIOS-e820: 000000002dffffc0 - 000000002e000000 (ACPI NVS) Oct 14 19:41:36 pau kernel: BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) oct 14 19:41:36 pau syslog: klogd startup succeeded Oct 14 19:41:36 pau kernel: 0MB HIGHMEM available. Oct 14 19:41:36 pau kernel: 735MB LOWMEM available. Oct 14 19:41:36 pau kernel: On node 0 totalpages: 188400 Oct 14 19:41:36 pau kernel: DMA zone: 4096 pages, LIFO batch:1 Oct 14 19:41:36 pau kernel: Normal zone: 184304 pages, LIFO batch:16 Oct 14 19:41:36 pau kernel: HighMem zone: 0 pages, LIFO batch:1 Oct 14 19:41:36 pau kernel: DMI 2.3 present. Oct 14 19:41:36 pau kernel: ACPI: RSDP (v000 OID_00 ) @ 0x000e5010 Oct 14 19:41:36 pau kernel: ACPI: RSDT (v001 INSYDE RSDT_000 0x00000001 _CSI 0x00010101) @ 0x2dfffbc0 Oct 14 19:41:36 pau kernel: ACPI: FADT (v001 INSYDE FACP_000 0x00000100 _CSI 0x00010101) @ 0x2dfffac0 Oct 14 19:41:36 pau kernel: ACPI: BOOT (v001 INSYDE SYS_BOOT 0x00000100 _CSI 0x00010101) @ 0x2dfffb50 Oct 14 19:41:36 pau kernel: ACPI: DBGP (v001 INSYDE DBGP_000 0x00000100 _CSI 0x00010101) @ 0x2dfffb80 Oct 14 19:41:36 pau kernel: ACPI: DSDT (v001 INSYDE KN266 0x00001000 MSFT 0x0100000e) @ 0x00000000 Oct 14 19:41:36 pau kernel: Building zonelist for node : 0 Oct 14 19:41:36 pau kernel: Kernel command line: ro root=LABEL=/ pci=noacpi pci=usepirqmask pci=biosirq Oct 14 19:41:36 pau kernel: Initializing CPU#0 Oct 14 19:41:36 pau kernel: PID hash table entries: 4096 (order 12: 32768 bytes) Oct 14 19:41:36 pau kernel: Detected 1525.914 MHz processor. Oct 14 19:41:36 pau kernel: Console: colour VGA+ 80x25 Oct 14 19:41:36 pau kernel: Memory: 742368k/753600k available (1642k kernel code, 10488k reserved, 711k data, 156k init, 0k highmem) Oct 14 19:41:36 pau kernel: Calibrating delay loop... 2981.88 BogoMIPS Oct 14 19:41:36 pau kernel: Security Scaffold v1.0.0 initialized Oct 14 19:41:36 pau kernel: SELinux: Initializing. Oct 14 19:41:36 pau kernel: SELinux: Starting in permissive mode Oct 14 19:41:36 pau kernel: There is already a security framework initialized, register_security failed. Failure registering capabilities with the kernel selinux_register_security: Registering secondary module capability Capability LSM initialized Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0183f9ff c1cbf9ff 00000000 00000000 CPU: After vendor identify, caps: 0183f9ff c1cbf9ff 00000000 00000000 Enabling disabled K7/SSE Support. CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000020 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD Athlon(tm) XP 1800+ stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xe8a04, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20030918 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] ACPI: Embedded Controller [EC0] (gpe 1) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay PCI: Probing PCI hardware PCI: Using IRQ router default [1106/3177] at 0000:00:11.0 PCI: Cannot allocate resource region 0 of device 0000:00:0a.0 divert: not allocating divert_blk for non-ethernet device lo SBF: Simple Boot Flag extension found and enabled. SBF: Setting boot flags 0x1 apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Initializing Cryptographic API PCI: Via IRQ fixup for 0000:00:10.1, from 255 to 0 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found pty: 2048 Unix98 ptys configured Real Time Clock Driver v1.12 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected VIA Apollo Pro266 chipset agpgart: Maximum main memory to use for agp memory: 658M agpgart: AGP aperture is 128M @ 0xb0000000 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:11.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1 ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdc:DMA, hdd:pio hda: IC25N030ATCS04-0, ATA DISK drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: UJDA740 DVD/CDRW, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 58605120 sectors (30005 MB) w/1768KiB Cache, CHS=58140/16/63, UDMA(100) hda: hda1 < hda5 hda6 hda7 hda8 hda9 hda10 > hda2 ide-floppy driver 0.99.newide mice: PS/2 mouse device common for all mice i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 input: PS/2 Generic Mouse on isa0060/serio4 serio: i8042 AUX3 port at 0x60,0x64 irq 12 input: AT Translated Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 NET: Registered protocol family 2 IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 175k freed VFS: Mounted root (ext2 filesystem). kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 156k freed drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub PCI: No IRQ known for interrupt pin D of device 0000:00:10.3. drivers/usb/core/hcd-pci.c: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.3 setup! drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 uhci-hcd 0000:00:10.0: UHCI Host Controller uhci-hcd 0000:00:10.0: irq 11, io base 00001200 uhci-hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected PCI: No IRQ known for interrupt pin B of device 0000:00:10.1. drivers/usb/core/hcd-pci.c: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.1 setup! drivers/usb/core/usb.c: registered new driver hiddev drivers/usb/core/usb.c: registered new driver hid drivers/usb/input/hid-core.c: v2.0:USB HID core driver EXT3 FS on hda6, internal journal Adding 811240k swap on /dev/hda10. Priority:-1 extents:1 kjournald starting. Commit interval 5 seconds EXT3 FS on hda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda8, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda9, internal journal EXT3-fs: mounted filesystem with ordered data mode. blk: queue edcf3b40, I/O limit 4095Mb (mask 0xffffffff) inserting floppy driver for 2.6.0-0.test7.1.52 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 ohci1394: $Rev: 1045 $ Ben Collins <[email protected]> ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[5] MMIO=[f0000000-f00007ff] Max Packet=[2048] i8k: not running on a Dell system i8k: vendor=Acer, model=Aspire 1310, version=3A2 i8k: unable to get SMM Dell signature i8k: unable to get SMM BIOS version ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f00000d4201] ip_tables: (C) 2000-2002 Netfilter core team via-rhine.c:v1.10-LK1.1.19-2.5 July-12-2003 Written by Donald Becker http://www.scyld.com/network/via-rhine.html divert: allocating divert_blk for eth0 eth0: VIA VT6102 Rhine-II at 0xe200, 00:c0:9f:29:06:73, IRQ 11. eth0: MII PHY found at address 1, status 0x7829 advertising 01e1 Link 0021. ip_tables: (C) 2000-2002 Netfilter core team Linux Kernel Card Services options: [pci] [cardbus] [pm] Yenta: CardBus bridge found at 0000:00:0a.0 [10cf:10e7] Yenta: ISA IRQ list 0098, PCI irq11 Socket status: 30000827 Bluetooth: Core ver 2.3 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.1 Bluetooth: L2CAP socket layer initialized hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 NET: Registered protocol family 10 Disabled Privacy Extensions on device c0319500(lo) IPv6 over IPv4 tunneling driver powernow: AMD K7 CPU detected. powernow: PowerNOW! Technology present. Can scale: frequency and voltage. powernow: Found PSB header at c00e5ed0 powernow: Table version: 0x12 powernow: Flags: 0x0 (Mobile voltage regulator) powernow: Settling Time: 100 microseconds. powernow: Has 1 PST tables. (Only dumping ones relevant to this CPU). powernow: PST:0 (@c00e5ee0) powernow: cpuid: 0x781 fsb: 133 maxFID: 0x1 startvid: 0xb powernow: FID: 0x4 (5.0x [665MHz]) VID: 0xc (1.400V) powernow: FID: 0x6 (6.0x [798MHz]) VID: 0xc (1.400V) powernow: FID: 0x8 (7.0x [931MHz]) VID: 0xc (1.400V) powernow: FID: 0x9 (7.5x [997MHz]) VID: 0xc (1.400V) powernow: FID: 0x9 (7.5x [997MHz]) VID: 0xc (1.400V) powernow: Minimum speed 665 MHz. Maximum speed 997 MHz. PCI: Setting latency timer of device 0000:00:11.5 to 64 cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x3c0-0x3df 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. $ lspci -vvv 00:00.0 Host bridge: VIA Technologies, Inc. P/KN266 Host Bridge Subsystem: VIA Technologies, Inc. P/KN266 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 8 Region 0: Memory at b0000000 (32-bit, prefetchable) [size=128M] Capabilities: <available only to root> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000c000-0000dfff Memory behind bridge: e0000000-efffffff Prefetchable memory behind bridge: a0000000-afffffff BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- Capabilities: <available only to root> 00:0a.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller Subsystem: Citicorp TTI: Unknown device 10e7 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 2e000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=02, subordinate=05, sec-latency=176 Memory window 0: 2e400000-2e7ff000 (prefetchable) Memory window 1: 2e800000-2ebff000 I/O window 0: 00001000-000010ff I/O window 1: 00001400-000014ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+ 16-bit legacy interface ports at 0001 00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI]) Subsystem: Citicorp TTI: Unknown device 1162 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 128 (500ns min, 1000ns max), cache line size 04 Interrupt: pin A routed to IRQ 5 Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at f0004000 (32-bit, non-prefetchable) [size=16K] Capabilities: <available only to root> 00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. USB Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 22 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at 1200 [size=32] Capabilities: <available only to root> 00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. USB Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 22 Interrupt: pin B routed to IRQ 0 Region 4: I/O ports at 1300 [size=32] Capabilities: <available only to root> 00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI]) Subsystem: VIA Technologies, Inc. USB 2.0 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 0 Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=256] Capabilities: <available only to root> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge Subsystem: VIA Technologies, Inc. VT8235 ISA Bridge Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: <available only to root> 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. VT8235 Bus Master ATA133/100/66/33 IDE Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin A routed to IRQ 0 Region 4: I/O ports at 1100 [size=16] Capabilities: <available only to root> 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 50) Subsystem: Acer Incorporated [ALI]: Unknown device 0030 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin C routed to IRQ 5 Region 0: I/O ports at e000 [size=256] Capabilities: <available only to root> 00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97 Modem] (rev 80) Subsystem: Acer Incorporated [ALI]: Unknown device 0030 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin C routed to IRQ 5 Region 0: I/O ports at e100 [size=256] Capabilities: <available only to root> 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74) Subsystem: Acer Incorporated [ALI]: Unknown device 0030 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 128 (750ns min, 2000ns max), cache line size 04 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at e200 [size=256] Region 1: Memory at f0008000 (32-bit, non-prefetchable) [size=256] Capabilities: <available only to root> 01:00.0 VGA compatible controller: S3 Inc. [ProSavageDDR K4M266] (prog-if 00 [VGA]) Subsystem: Acer Incorporated [ALI]: Unknown device 0030 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 128 (1000ns min, 63750ns max), cache line size 04 Interrupt: pin A routed to IRQ 11 Region 0: Memory at e0080000 (32-bit, non-prefetchable) [size=512K] Region 1: Memory at a8000000 (32-bit, prefetchable) [size=128M] Expansion ROM at 000c0000 [disabled] [size=64K] Capabilities: <available only to root> $ cat /proc/interrupts CPU0 0: 58055254 XT-PIC timer 1: 40202 XT-PIC i8042 2: 0 XT-PIC cascade 5: 12401 XT-PIC ohci1394, VIA8233 8: 1 XT-PIC rtc 9: 1851 XT-PIC acpi 11: 291078 XT-PIC uhci-hcd, eth0, yenta 12: 279317 XT-PIC i8042 14: 141898 XT-PIC ide0 15: 2675 XT-PIC ide1 NMI: 0 ERR: 0 $ cat /proc/ioports 0000-001f : dma1 0020-0021 : pic1 0040-005f : timer 0060-006f : keyboard 0070-0077 : rtc 0080-008f : dma page reg 00a0-00a1 : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 0376-0376 : ide1 0378-037a : parport0 037b-037f : parport0 03c0-03df : vga+ 03f6-03f6 : ide0 0cf8-0cff : PCI conf1 1000-10ff : PCI CardBus #02 1100-110f : 0000:00:11.1 1100-1107 : ide0 1108-110f : ide1 1200-121f : 0000:00:10.0 1200-121f : uhci-hcd 1300-131f : 0000:00:10.1 1400-14ff : PCI CardBus #02 c000-dfff : PCI Bus #01 e000-e0ff : 0000:00:11.5 e000-e0ff : VIA8233 e100-e1ff : 0000:00:11.6 e200-e2ff : 0000:00:12.0 e200-e2ff : via-rhine $ cat /proc/iomem 00000000-0009fbff : System RAM 0009fc00-0009ffff : reserved 000a0000-000bffff : Video RAM area 000e0000-000effff : Extension ROM 000f0000-000fffff : System ROM 00100000-2dfeffff : System RAM 00100000-0029a82d : Kernel code 0029a82e-0034c5ff : Kernel data 2dff0000-2dffffbf : ACPI Tables 2dffffc0-2dffffff : ACPI Non-volatile Storage 2e000000-2e000fff : 0000:00:0a.0 2e000000-2e000fff : yenta_socket 2e400000-2e7fffff : PCI CardBus #02 2e800000-2ebfffff : PCI CardBus #02 a0000000-afffffff : PCI Bus #01 a8000000-afffffff : 0000:01:00.0 b0000000-b7ffffff : 0000:00:00.0 e0000000-efffffff : PCI Bus #01 e0080000-e00fffff : 0000:01:00.0 f0000000-f00007ff : 0000:00:0c.0 f0000000-f00007ff : ohci1394 f0004000-f0007fff : 0000:00:0c.0 f0008000-f00080ff : 0000:00:12.0 f0008000-f00080ff : via-rhine f4000000-f40000ff : 0000:00:10.3 fff80000-ffffffff : reserved Pau ------------------------------------------------------- This SF.net email is sponsored by: SF.net Giveback Program. SourceForge.net hosts over 70,000 Open Source Projects. See the people who have HELPED US provide better services: Click here: http://sourceforge.net/supporters.php