[ACPI-sppt] Acer TravelMate 233xc ACPI, no sleep state S1

I installed the kernel version 2.4.21-rc3, with the latest acpi patch.


/proc/acpi/info states:

version:                 20030522
states:                  S0 S3 S4 S5 

This is odd, since there probably should be a S1, since that's the only
one supported so far, right? Maybe this system is too new?


I get this at boot time:

    ACPI-0286: *** Error: No installed handler for fixed event
[00000000]


And the rest of the kernel ACPI printout:

ACPI: RSDP (v000 PTLTD                      ) @ 0x000f5c60
ACPI: RSDT (v001 PTLTD    RSDT   01540.00000) @ 0x0f7698d1
ACPI: FADT (v001 INTEL  NBGV     01540.00000) @ 0x0f76df14
ACPI: MADT (v001 PTLTD           APIC   01540.00000) @ 0x0f76df88
ACPI: BOOT (v001 PTLTD  $SBFTBL$ 01540.00000) @ 0x0f76dfd8
ACPI: DSDT (v001   WIST  PELICAN 01540.00000) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: Subsystem revision 20030522
PCI: PCI BIOS revision 2.10 entry at 0xfd824, last bus=2
PCI: Using configuration type 1
    ACPI-0286: *** Error: No installed handler for fixed event
[00000000]
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Embedded Controller [EC] (gpe 28)
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs 10, enabled at IRQ 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11, disabled)
ACPI: PCI Interrupt Link [LNKF] (IRQs 11, disabled)
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11, disabled)
ACPI: PCI Interrupt Link [LNKH] (IRQs *11)
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU] (supports C1 C2 C3, 8 throttling states)
ACPI: Thermal Zone [THM0] (24 C)

(The battery wasn't in when this was taken)

Running acpid and ospmd works, but ospm_gui segfaults.



-------------------------------------------------------
This SF.net email is sponsored by:  Etnus, makers of TotalView, The best
thread debugger on the planet. Designed with thread debugging features
you've never dreamed of, try TotalView 6 free at www.etnus.com.