[ACPI-sppt] No ACPI Battery info for Inspiron 1100
Damien Solley <[email protected]>
| Newsgroups | gmane.linux.acpi.support |
|---|---|
| Message-ID | <1057962805.21767.11.camel@localhost> |
Hi ACPI List
I'm trying to get battery info on my spanky new Inspiron laptop. I
installed the ACPI patch against kernel 2.4.21, and it partly works (I
have thermal info and AC-adaptor status). However, I don't have any
battery status info, which is my primary reason for needing ACPI.
I have no listing in /proc/acpi/battery, ie the directory is empty.
I have compiled all the ACPI stuff directly into the kernel. My dmesg
ouput is below, in case it proves useful.
Cheers and TIA
Damien
Linux version 2.4.21-ck3 (root@laptop) (gcc version 3.3.1 20030626
(Debian prerelease)) #18 Tue Jul 8 00:55:49 GMT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fe70000 (usable)
BIOS-e820: 000000001fe70000 - 000000001fe7b000 (ACPI data)
BIOS-e820: 000000001fe7b000 - 000000001fe80000 (ACPI NVS)
BIOS-e820: 000000001fe80000 - 0000000020000000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
510MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 130672
zone(0): 4096 pages.
zone(1): 126576 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 PTLTD ) @ 0x000f78e0
ACPI: RSDT (v001 PTLTD RSDT 01540.00000) @ 0x1fe76dd0
ACPI: FADT (v001 INTEL NBGV 01540.00000) @ 0x1fe7af64
ACPI: BOOT (v001 PTLTD $SBFTBL$ 01540.00000) @ 0x1fe7afd8
ACPI: DSDT (v001 INTEL Brkdle_G 01540.00000) @ 0x00000000
ACPI: BIOS passes blacklist
Kernel command line: hda=ide-scsi ro root=/dev/hdc6 vga=773 3
ide_setup: hda=ide-scsi
Initializing CPU#0
Detected 1993.484 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3956.73 BogoMIPS
Memory: 513336k/522688k available (2200k kernel code, 8964k reserved,
-2560k data, 140k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebf9ff 00000000 00000000 00000000
CPU: Common caps: bfebf9ff 00000000 00000000 00000000
CPU: Intel(R) Celeron(R) CPU 2.00GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
ACPI: Subsystem revision 20030522
PCI: PCI BIOS revision 2.10 entry at 0xfd9b2, last bus=2
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SLOT._PRT]
ACPI: Embedded Controller [EC0] (gpe 28)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 10 11 14 15, disabled)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 10 11 14 15, disabled)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 11 14 15, disabled)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 10 11 14 15, disabled)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *10 11 14 15)
schedule_task(): keventd has not started
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd & kiswapd
Journalled Block Device driver loaded
ACPI: AC Adapter [ACAD] (off-line)
ACPI-0352: *** Error: Looking up [Z000] in namespace, AE_NOT_FOUND
search_node c1597a80 start_node c1597a80 return_node 00000000
ACPI-1121: *** Error: Method execution failed
[\_SB_.PCI0.LPC0.BAT1._BIF] (Node c1597a80), AE_NOT_FOUND
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
ACPI: Processor [CPU0] (supports C1 C2, 8 throttling states)
ACPI: Thermal Zone [THRM] (42 C)
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G
chipsets
intelfb: Version 0.7.5, written by David Dawes
<[email protected]>
intelfb: 00:02.0: Intel(R) 845G, aperture size 128MB, stolen memory
892kB
intelfb: Acceleration is not supported for the Intel(R) 845G chipset.
intelfb: Non-CRT device is enabled (DVO port C). Disabling mode
switching.
intelfb: Initial video mode is 1024x768-8@60.
Console: switching to colour frame buffer device 128x48
vesafb: abort, cannot reserve video memory at 0xf0000000
vesafb: framebuffer at 0xf0000000, mapped to 0xe096c000, size 6144k
vesafb: mode is 1024x768x8, linelength=1024, pages=0
vesafb: protected mode interface info at a5f3:1f5f
vesafb: scrolling: redraw
fb1: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
i8k: unable to get SMM BIOS version
Dell laptop SMM driver v1.13 14/05/2002 Massimo Dal Zotto
([email protected])
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI ISAPNP enabled
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 438M
agpgart: Detected an Intel 845G Chipset.
agpgart: detected 892K stolen memory.
agpgart: AGP aperture is 128M @ 0xf0000000
[drm] AGP 0.99 on Intel i810 @ 0xf0000000 128MB
[drm] Initialized i810 1.2.0 20010920 on minor 0
[drm] AGP 0.99 on Intel i810 @ 0xf0000000 128MB
[drm] Initialized i830 1.2.0 20011004 on minor 1
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2020-0x2027, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2028-0x202f, BIOS settings: hdc:DMA, hdd:pio
hda: MATSHITA CD-RW UJDA360, ATAPI CD/DVD-ROM drive
hdc: IC25N030ATCS04-0, ATA DISK drive
blk: queue c0179a1c, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hdc: attached ide-disk driver.
hdc: host protected area => 1
hdc: 58605120 sectors (30006 MB) w/1768KiB Cache, CHS=58140/16/63,
UDMA(100)
Partition check:
hdc: [PTBL] [3648/255/63] hdc1 hdc2 hdc3 < hdc5 hdc6 hdc7 >
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
Intel 810 + AC97 Audio, version 0.24, 23:33:31 Jul 6 2003
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH4 found at IO 0x1c80 and 0x1400, MEM 0xe0080c00 and
0xe0080800, IRQ 10
i810: Intel ICH4 mmio at 0xe0ff3c00 and 0xe0ff5800
i810_audio: Primary codec has ID 0
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 0
ac97_codec: AC97 Audio codec, id: 0x8384:0x7650 (Unknown)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Yenta IRQ list 0000, PCI irq10
Socket status: 30000010
PCI: Setting latency timer of device 00:1d.7 to 64
ehci-hcd 00:1d.7: Intel Corp. 82801DB USB EHCI Controller
ehci-hcd 00:1d.7: irq 10, pci mem e0ff9000
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd 00:1d.7: enabled 64bit PCI DMA
PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:1d.7 PCI cache line size corrected to 128.
ehci-hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 4 ports detected
host/uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Setting latency timer of device 00:1d.0 to 64
host/uhci.c: USB UHCI at I/O 0x1cc0, IRQ 10
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
host/uhci.c: USB UHCI at I/O 0x1ce0, IRQ 11
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]>
hid-core.c: USB HID support drivers
usb.c: registered new driver usblp
printer.c: v0.11: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
md: raid1 personality registered as nr 3
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
IPv4 over IPv4 tunneling driver
ip_conntrack version 2.1 (4083 buckets, 32664 max) - 292 bytes per
conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 140k freed
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,6), internal journal
grsec: time set by (hwclock:28983) UID(0) EUID(0), parent (rcS:28715)
UID(0) EUID(0)
grsec: time set by (hwclock:3114) UID(0) EUID(0), parent (rcS:28715)
UID(0) EUID(0)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
cs: warning: no high memory space available!
cs: unable to map card memory!
cs: unable to map card memory!
hda: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MATSHITA Model: UJDA360 Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: MATSHITA Model: UJDA360 Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: MATSHITA Model: UJDA360 Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: MATSHITA Model: UJDA360 Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: MATSHITA Model: UJDA360 Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: MATSHITA Model: UJDA360 Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: MATSHITA Model: UJDA360 Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 0, lun 1
Attached scsi CD-ROM sr2 at scsi0, channel 0, id 0, lun 2
Attached scsi CD-ROM sr3 at scsi0, channel 0, id 0, lun 3
Attached scsi CD-ROM sr4 at scsi0, channel 0, id 0, lun 4
Attached scsi CD-ROM sr5 at scsi0, channel 0, id 0, lun 5
Attached scsi CD-ROM sr6 at scsi0, channel 0, id 0, lun 6
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
sr2: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
sr3: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
sr4: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
sr5: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
sr6: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
cs: unable to map card memory!
cs: unable to map card memory!
ASSERT ip_conntrack_core.c:625 &ip_conntrack_lock not readlocked
grsec: time set by (hwclock:24819) UID(0) EUID(0), parent (rcS:21340)
UID(0) EUID(0)
Broadcom 4401 Ethernet Driver bcm4400 ver. 2.0.2 (04/28/03)
ASSERT failed: (REG_RD(pDevice, emacintstatus) & EI_MII) == 0
ASSERT failed: (REG_RD(pDevice, emacintstatus) & EI_MII) == 0
ASSERT failed: (REG_RD(pDevice, emacintstatus) & EI_MII) == 0
ASSERT failed: (REG_RD(pDevice, emacintstatus) & EI_MII) == 0
eth0: Broadcom BCM4401 100Base-T found at mem e0100000, IRQ 10, node
addr 000bdb9572b2
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x20f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
prism2_init: prism2_cs.o: 0.2.1-pre9 Loaded
prism2_init: dev_info is: prism2_cs
prism2_cs: index 0x01: Vcc 5.0, irq 10, io 0x0100-0x013f
ident: nic h/w: id=0x8002 1.0.0
ident: pri f/w: id=0x15 0.3.0
ident: sta f/w: id=0x1f 0.8.3
MFI:SUP:role=0x00:id=0x01:var=0x01:b/t=1/1
CFI:SUP:role=0x00:id=0x02:var=0x01:b/t=1/1
PRI:SUP:role=0x00:id=0x03:var=0x01:b/t=1/2
STA:SUP:role=0x00:id=0x04:var=0x01:b/t=1/6
PRI-CFI:ACT:role=0x01:id=0x02:var=0x01:b/t=1/1
STA-CFI:ACT:role=0x01:id=0x02:var=0x01:b/t=1/1
STA-MFI:ACT:role=0x01:id=0x01:var=0x01:b/t=1/1
Prism2 card SN: 99SA01000000
linkstatus=CONNECTED
-------------------------------------------------------
This SF.Net email sponsored by: Parasoft
Error proof Web apps, automate testing & more.
Download & eval WebKing and get a free book.
www.parasoft.com/bulletproofapps1