Re: Problem with sending a reply to the list - previous replies were OK . .

lists,


On 2020-08-03 17:13, lists wrote:
> I run my own email server. I use this to verify my server is working 
> properly.
> 
> https://dkimvalidator.com/


Thanks - I will have a look.


> I haven't been following this thread. If you aren't running your own
> email server, I don't see how you can effect SPF or DKIM.


Yes I do run my own email server (IndiMail - an updated version of 
QMail) - the problem is that of the reports I get daily about my setup, 
only roughly 50% pass DKIM - it is better for SPF.  I don't understand 
why it is not 0% or 100% . .


> SPF means your email comes from an IP address that is allowed to send
> email from your domain.


Yes.


> This is handled by your DNS. DKIM is
> substantially more difficult to explain. It is a way to
> cryptographically sign your message. If you pass DKIM then the message
> has not been altered.


How could my DKIM setup not be either 0% or 100% ?


> One way to fail SPF is to use a remailer.


Well I don't have that problem . .

Thanks for the info!

Phil.




> 	  Original Message  
> 
> 
> From: [email protected]
> Sent: August 2, 2020 11:45 PM
> To: [email protected]
> Reply-to: [email protected]
> Cc: [email protected]
> Subject: Re: [Alsa-user] Problem with sending a reply to the list -
> previous replies were OK . .
> 
> 
> Alan,
> 
> 
> On 2020-08-03 01:43, Alan Corey wrote:
>> I don''t remember the exact error message, it was something like
>> "unable to establish secure connection to ...".  I spent a lot of time
>> digging into it and the simple fix was just to reboot the router which
>> hadn't been done in months.  My router then was a cell phone with
>> battery and charger so it was mostly always up.  It was affecting SSL
>> connections to some web sites but not all.
> 
> 
> As expected, rebooting my modem did not help - I still get the DKIM
> error messages when I post to this list - I will just have to spend 
> more
> time on it yet again to try and work out why some sites are failing . .
> it would be nice if there are some DKIM / DMARC / SPF gurus here who
> could help me . .
> 
> Thanks,
> 
> Phil.
> 
> 
> 
>> On 8/2/20, Philip Rhoades <[email protected]> wrote:
>>> Alan,
>>> 
>>> 
>>> On 2020-07-30 14:44, Alan Corey wrote:
>>>> When was the last time you rebooted your router?  I've seen that
>>>> solve
>>>> weird things.
>>> 
>>> 
>>> Just did that now before sending this reply . . but I bet I will get
>>> this stupid DMARC / DKIM problem again . .
>>> 
>>> Thanks,
>>> 
>>> P.
>>> 
>>> 
>>>> On 7/30/20, Philip Rhoades <[email protected]> wrote:
>>>>> Alan,
>>>>> 
>>>>> 
>>>>> On 2020-07-29 23:58, Alan Corey wrote:
>>>>>> Could it be because you changed the subject line?  It wouldn't
>>>>>> surprise me if something does a hash of the subject.  I don't know
>>>>>> a
>>>>>> lot about secure email with SSL and all that.
>>>>> 
>>>>> 
>>>>> I don't think so - posting this note also caused me to receive
>>>>> similar
>>>>> error messages - even though in both cases the email made it onto
>>>>> the
>>>>> list . . must be some sort of DKIM problem I think . .
>>>>> 
>>>>> Thanks,
>>>>> 
>>>>> Phil.
>>>>> 
>>>>> 
>>>>>> On 7/29/20, Philip Rhoades <[email protected]> wrote:
>>>>>>> People,
>>>>>>> 
>>>>>>> I tried to reply to my previous thread with a slightly modified
>>>>>>> Subject:
>>>>>>> 
>>>>>>>     SOLVED: Re: Anybody got Google Meet going on Linux (Fedora)
>>>>>>> with
>>>>>>> just
>>>>>>> ALSA (ie not with PulseAudio)?
>>>>>>> 
>>>>>>> and received a response:
>>>>>>> 
>>>>>>> This is an authentication failure report for an email message
>>>>>>> received
>>>>>>> from pricom.com.au on Wed Jul 29 10:43:32 UTC 2020
>>>>>>> Received-SPF: pass (domain of lists.sourceforge.net designates
>>>>>>> 216.105.38.7 as permitted sender)
>>>>>>> Authentication-Results: atlas201.free.mail.ir2.yahoo.com;
>>>>>>>    dkim=perm_fail [email protected] header.s=x;
>>>>>>>    dkim=perm_fail [email protected] header.s=x;
>>>>>>>    dkim=perm_fail [email protected] header.s=phr1;
>>>>>>>    spf=pass smtp.mailfrom=lists.sourceforge.net;
>>>>>>>    dmarc=success(p=NONE,sp=NONE) header.from=pricom.com.au;
>>>>>>> .
>>>>>>> .
>>>>>>> 
>>>>>>> How can I fix this?
>>>>>>> 
>>>>>>> Thanks,
>>>>>>> 
>>>>>>> Phil.
>>>>>>> --
>>>>>>> Philip Rhoades
>>>>>>> 
>>>>>>> PO Box 896
>>>>>>> Cowra  NSW  2794
>>>>>>> Australia
>>>>>>> E-mail:  [email protected]
>>>>>>> 
>>>>>>> 
>>>>>>> _______________________________________________
>>>>>>> Alsa-user mailing list
>>>>>>> [email protected]
>>>>>>> https://lists.sourceforge.net/lists/listinfo/alsa-user
>>>>>>> 
>>>>> 
>>>>> --
>>>>> Philip Rhoades
>>>>> 
>>>>> PO Box 896
>>>>> Cowra  NSW  2794
>>>>> Australia
>>>>> E-mail:  [email protected]
>>>>> 
>>> 
>>> --
>>> Philip Rhoades
>>> 
>>> PO Box 896
>>> Cowra  NSW  2794
>>> Australia
>>> E-mail:  [email protected]
>>> 
> 
> --
> Philip Rhoades
> 
> PO Box 896
> Cowra  NSW  2794
> Australia
> E-mail:  [email protected]
> 
> 
> _______________________________________________
> Alsa-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/alsa-user
> 
> _______________________________________________
> Alsa-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/alsa-user

-- 
Philip Rhoades

PO Box 896
Cowra  NSW  2794
Australia
E-mail:  [email protected]


_______________________________________________
Alsa-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-user