Re: Re: Kernel panic when installing on SS10

Just a bit of "useless information" but I had attempted to install the
1.92 version on my Sun Ultra5 but never succeeded. Aurora 1.0 installed
and ran very well. I now have Aurora 2.0 installed and working very very
well. The only problem I'm having is certain extra packages give me a
"groupkey" error and will not install. I assume these will be corrected
as time goes on. Otherwise I'm very pleased with how easy 2.0 installed
and I was able to update with yum.

Thx,
Jim Birdsong


On Sat, 2006-08-12 at 17:19 +0200, T. Ribbrock wrote:
> On Thu, Aug 03, 2006 at 05:11:23PM +0200, T. Ribbrock wrote:
> > I still haven't succeeded in installing Aurora 2.0 on my SS10 - the
> > install always fails in the same spot: right after installing
> > glibc-common, the machine hangs and then produces a kernel panic (the
> > last message is "Aiee, killing interrupt handler").
> [...]
> 
> By now, I've succesfully installed Aurora 1.0 on that box[0]. The
> install went without a hitch (contrary to 2.0...). The only thing I
> noticed was in the dmesg when I booted the system for the first time:
> 
> [...]
> VFS: Mounted root (ext2 filesystem).
> esp0: IRQ 36 SCSI ID 7 Clk 40MHz CCYC=25000 CCF=8 TOut 167
> NCR53C9XF(espfast)
> ESP: Total of 1 ESP hosts found, 1 actually in use.
> scsi0 : Sparc ESP100A-FAST
> esp0: hoping for msgout
>   Vendor: FUJITSU   Model: M2694ES-512       Rev: 8134
>   Type:   Direct-Access                      ANSI SCSI revision: 02
>   Vendor: CyberDrv  Model:  CD-ROM TW240S    Rev: 1.40
>   Type:   CD-ROM                             ANSI SCSI revision: 02
> Attached scsi disk sda at scsi0, channel 0, id 3, lun 0
> SCSI device sda: 2117025 512-byte hdwr sectors (1084 MB)
> Partition check:
>  sda: sda1 sda2 sda3 sda4
> Journalled Block Device driver loaded
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> Freeing unused kernel memory: 308k freed
> scsi : aborting command due to timeout : pid 104, scsi0, channel 0, id
> 3, lun 0 
> Read (10) 00 00 17 e4 23 00 00 40 00 
> esp0: Aborting command
> esp0: dumping state
> esp0: dma -- cond_reg<a6400310> addr<f01f4400>
> esp0: SW [sreg<11> sstep<04> ireg<10>]
> esp0: HW reread [sreg<01> sstep<44> ireg<00>]
> esp0: current command [tgt<03> lun<00> pphase<CLUELESS> cphase<DATAIN>]
> esp0: disconnected 
> SCSI host 0 abort (pid 104) timed out - resetting
> SCSI bus is being reset for host 0 channel 0.
> esp0: Resetting scsi bus
> esp0: Gross error sreg=40
> esp0: SCSI bus reset interrupt
> esp0: hoping for msgout
> Adding Swap: 164000k swap-space (priority -1)
> EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,4), internal journal
> md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> scsi : aborting command due to timeout : pid 1201, scsi0, channel 0, id
> 3, lun 0
>  Read (10) 00 00 10 c2 eb 00 00 18 00 
> esp0: Aborting command
> esp0: dumping state
> esp0: dma -- cond_reg<a6400310> addr<f3d46800>
> esp0: SW [sreg<11> sstep<04> ireg<10>]
> esp0: HW reread [sreg<01> sstep<c4> ireg<00>]
> esp0: current command [tgt<03> lun<00> pphase<CLUELESS> cphase<DATAIN>]
> esp0: disconnected 
> SCSI host 0 abort (pid 1201) timed out - resetting
> SCSI bus is being reset for host 0 channel 0.
> esp0: Resetting scsi bus
> esp0: Gross error sreg=40
> esp0: SCSI bus reset interrupt
> esp0: hoping for msgout
> 
> Anybody an idea whether this could have anything to do with Aurora 2.0
> panicing during install?
> 
> Cheerio,
> 
> Thomas
> 
> [0] shocking, really - the installer is quite a bit faster than the
> Aurora 2.0 one - and the minimum install is almost 300MB(!) smaller...
> %-}

_______________________________________________
Aurora-sparc-user mailing list
[email protected]
http://lists.auroralinux.org/mailman/listinfo/aurora-sparc-user
Aurora FAQ: http://www.ecs.soton.ac.uk/~mas01r/aurorafaq.html