Re: pin code

Hi Prabhu
I have a question. I have cross compiled dbus-0.93 and flashed the image in my hardware platform. Now when i run dbus-daemon --system it gives me an error
Failed to open connection to system message bus: Failed to connect to socket /usr/local/var/run/dbus/system_bus_socket: No such file or directory

I am a bit confused here because you write that system_bus_socket is created when dbus-daemon is started. However in my case it is expecting the socket file to be present when I start dbus-daemon.

Can you please clarify how do i solve this problem?
 

Regards,
Sumeet 

 

  _____  

From: [email protected] [mailto:[email protected]] On Behalf Of Prabhu nath
Sent: Friday, January 26, 2007 11:15 AM
To: BlueZ users
Subject: Re: [Bluez-users] pin code


You have to cross-compile dbus-1.0, and start dbus-daemon before executing hcid. 
dbus-daemon --system
 
While cross-compiling dbus-1.0 and bluez-utils, pass the following parameters for the configure script.
--localstatedir=/var --sysconfdir=/etc
 
Once you do this, by default hcid will look for hcid.conf in /etc/bluetooth directory. 
 
 
Warning. Take a backup of /etc/dbus-1 and /etc/bluetooth, because this will overwrite the previous config, which was already present in ur system.
 
Run make install for dbus, and u need not run make install for bluez-utils. U can directly copy the hcid.conf and blue-hcid.conf to /etc/bluetooth and /etc/dbus-1/system.d directory respectively.
 
Now, when u start dbus-daemon --system, it will create a system_bus_socket in /var/run/dbus and it will create a message.pid in /var/run/. 
 
next, when u start hcid, u should not get problem.
 
-Prabhu
 


 
On 1/23/07, KS H <[email protected]> wrote: 

Dear

I cross compile the bluez3.8 and try to setup the bluetooth in arm. I connect the arm with CSR BC03 with BCSP configuration. I am able to make the Bluez discoverable and try to pair bluez. however i found that there is no pin respond from Bluez. So i try to configure bluez using hcid. 

> hcid -n -f /etc/bluetooth/hcid.conf

it return

hcid[481]: Can't connect to system message bus: Failed to connect to socket /usr/local/var/run/dbus/system_bus_socket:  No such file or directory 
hcid[481]: Unable to get on D-Bus

My question
1. where can I found the missing file and what is that used for?
2. Is there any method to repsond the pin request other than using hcid

Regards
SH


_______________________________________
YM - 離線訊息
就算你沒有上網，你的朋友仍可以留下訊息給你，當你上網時就能立即看到，任何說話都冇走失。
http://messenger.yahoo.com.hk  <http://messenger.yahoo.com.hk/> 


-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your 
opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php <http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV> &p=sourceforge&CID=DEVDEV

_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users  <https://lists.sourceforge.net/lists/listinfo/bluez-users>

-------------------------------------------------------------------------
SF.Net email is sponsored by:
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services
for just about anything Open Source.
http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace

_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users