Re: How to use Bluez with CSR chip ?

Hi henry

    Thanks for you reply.

    Yes , I am using BC4 A06 Rom version on an arm based embedded board.

    So this one must set pskey before running right ?

    I try to run the CSR's demo first to set the right pskey and run the 
chip up.
    After I exit the demo, I can use pc to detect the chip.

    While , then I use :

    hciattach /dev/ttyS1 bcsp 921600

    to attach ttyS1 to hci0

    after that , The PC can not detect the chip anymore.

    and then I try
    hciconfig hci0 up
    it can bring up the hci0 interface , but the pc still don't detect the 
chip.

    for kernel , I only insert bluetooth.ko and hci_uart.ko

    So , can you kindly figure out what might be wrong in my operation ?

    Seems to me the hciattach operation reset the chip. And I might need to 
modify the hciattach , or ?

Raymond

----- Original Message ----- 
From: "hong zhang" <[email protected]>
To: "BlueZ users" <[email protected]>
Sent: Wednesday, June 11, 2008 8:57 AM
Subject: Re: [Bluez-users] How to use Bluez with CSR chip ?


> Raymond,
>
> CSR bc4 is initialized in two ways based on your
> design. I assum your board is embedded. One is by
> eeprom and one is using command after build. You need
> to provide more information.
>
> You have to make sure your CSR bc4 chip on your board
> is up first before using bluez.
>
> Regular talking here is based on x86.
>
> ---henry
>
> --- colorant <[email protected]> wrote:
>
>> Hi
>>
>>     I am not sure is this the proper place to put up
>> this question, if not ,
>> please correct me.
>>
>>     I was trying to run bluez on our board with bc4
>> chip. This chip need to
>> set pskey before it can run
>>
>>     I use hciattach and hciconfig to bring up the
>> hci0 interface.
>>
>>     Then I try hcitool hci0 scan with my earphone
>> open.
>>
>>     Nothing happend.
>>
>>     while, if I using CSR's bchs a2dp demo , it's
>> ok, I can play music. say
>> hardware is ok.
>>
>>     My question is :
>>
>>     1. To enable bluez with csr chip, is there
>> anything need to do vs the
>> standard kernel and bluez package ? Some config
>> need?
>>
>>     2. Did I need to place the bootrap init sequence
>> for the bc4 chip in
>> some place if I using bluez ? say in kernel or in
>> the bluez user space
>> scripts? Or , the standard kernel and bluez utility
>> already hand it, But I
>> just do the wrong way ?
>>
>>
>> Many thanks.
>> Raymond
>>
>>
>>
>>
>>
> -------------------------------------------------------------------------
>> Check out the new SourceForge.net Marketplace.
>> It's the best place to buy or sell services for
>> just about anything Open Source.
>> http://sourceforge.net/services/buy/index.php
>> _______________________________________________
>> Bluez-users mailing list
>> [email protected]
>>
> https://lists.sourceforge.net/lists/listinfo/bluez-users
>>
>
>
>
>
>
> -------------------------------------------------------------------------
> Check out the new SourceForge.net Marketplace.
> It's the best place to buy or sell services for
> just about anything Open Source.
> http://sourceforge.net/services/buy/index.php
> _______________________________________________
> Bluez-users mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/bluez-users
> 




-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://sourceforge.net/services/buy/index.php