Re: Problems installing on Lenny

Sergi Barroso escribió:
> John Hughes escribió:
>   
>> Sergi Barroso wrote:
>>     
>>> John Hughes escribió:
>>>       
>>>> Sergi Barroso wrote:
>>>>         
>>>>> John Hughes escribió: 
>>>>>           
>>>> I will check to see where /cluster/lib/cfstab is supposed to be 
>>>> created.
>>>>
>>>>         
>>> These is all files inside /cluster/lib/
>>>
>>> # ls /cluster/lib/
>>> Clustertab.pm  CVIP.pm    ssi_arch.pm  ssi_distro.pm  ssi_mgmt.pm  
>>> ssi_utils.pm
>>>
>>>       
>> So, /cluster/lib/cfstab doesn't exist.  This is bad.
>>
>> On my system:
>>
>>     # dpkg -s /cluster/lib/cfstab
>>     mount: /cluster/lib/cfstab
>>     # dpkg -l mount
>>     Desired=Unknown/Install/Remove/Purge/Hold
>>     | Status=Not/Inst/Cfg-files/Unpacked/Failed-cfg/Half-inst/trig-aWait/Trig-pend
>>     |/ Err?=(none)/Hold/Reinst-required/X=both-problems (Status,Err: uppercase=bad)
>>     ||/ Name              Version              Description
>>     +++-=================-====================-===============================================
>>     ii  mount             2.13.1.1-1.ssi1      Tools for mounting and manipulating filesystems
>>
>>       
>>
>> What version of mount do you have installed?
>>
>> What is in your /etc/apt/sources.list file?
>>
>> What is in your /etc/apt/preferences file?
>>
>>     
> Yes, that's mount package probleme, thanks you, I modified apt 
> prefrences after installed openssi, that's the problem, thanks!
>
> Now I can continue my config.
>
> Tnx again
>
>   
Hi!

This is the config of my cluster:


The following configuration has been entered:
    Node number:        1
    NIC for interconnect:    eth1
    IP address:        10.0.0.1
    Network hardware addr:    00:11:95:D7:57:87
    Network boot protocol:    PXE
    Local boot device:    UUID="a8b94708-85d6-46c8-be1a-34d01ba3f994"
    Clustername:        test-cluster
    Root failover:        No
    Potential initnode:    Yes
    NFS support:        yes

Then I get this error:

inding valid ramdisk creators.
Using mkinitrd to build the ramdisk.
/usr/sbin/mkinitrd: add_modules_dep_2_5: modprobe failed
FATAL: Module skge not found.
WARNING: This failure MAY indicate that your kernel will not boot!
but it can also be triggered by needed modules being compiled into
the kernel.
cpio: initrd/lib/i686/cmov/libc.so.6 not created: newer or same age 
version exists
cpio: initrd/lib/libcluster.so.0 not created: newer or same age version 
exists
This command requires a CI/OpenSSI kernel.
This command requires a CI/OpenSSI kernel.
6280+0 records in
6280+0 records out
6430720 bytes (6,4 MB) copied, 0,0196778 s, 327 MB/s
FATAL: Could not load /lib/modules/2.6.26-1-686/modules.dep: No such 
file or directory
mke2fs 1.40-WIP (14-Nov-2006)
check_mntent_file: Can't open /proc/1/where
check_mntent_file: Can't open /proc/1/where
cpio: ./dev/ide: Cannot stat: No existe el fichero o el directorio
cpio: ./dev/cciss: Cannot stat: No existe el fichero o el directorio
cpio: ./dev/ida: Cannot stat: No existe el fichero o el directorio
cpio: ./dev/md: Cannot stat: No existe el fichero o el directorio
cpio: ./dev/mapper: Cannot stat: No existe el fichero o el directorio
cpio: ./dev/scsi: Cannot stat: No existe el fichero o el directorio
9825 blocks
/boot/initrd.img-2.6.12-ssi-686-smp.new:     69.7% -- replaced with 
/boot/initrd.img-2.6.12-ssi-686-smp.new.gz
Running postinst hook script update-grub.

After I reboots the system, on howto step 15 it halts on boot, after 
devfs problem message.

Any help here?

-- 
Sergi Barroso
Linux user #313577
PGPID: D318F5E8
http://www.lionclan.org


------------------------------------------------------------------------------
Apps built with the Adobe(R) Flex(R) framework and Flex Builder(TM) are
powering Web 2.0 with engaging, cross-platform capabilities. Quickly and
easily build your RIAs with Flex Builder, the Eclipse(TM)based development
software that enables intelligent coding and step-through debugging.
Download the free 60 day trial. http://p.sf.net/sfu/www-adobe-com