[comedi] ni_pcimio does not support attach using comedi_config

------=_Part_7120_731089079.1688084972410
Content-Type: multipart/alternative; 
	boundary="----=_Part_7121_981152476.1688084972410"

------=_Part_7121_981152476.1688084972410
Content-Type: text/plain; charset="UTF-8"

Hello everyone,

I'm using a National Instruments PCI-6014 188626D-01 daq and trying to run 
comedi_config to setup the daq. Initially, I kept getting the "comedi.o not 
loaded" error and fixed it by setting autoconfig=0. However now, I'm 
getting the following error:

configuring driver=ni_pcimio 0,0,0,0,0,...0,0,0
Configure failed!: Input/output error
Check kernel log for more information
Possible reasons for failure:
  Driver not found

If I check kernel logs using "dmesg", I see: "comedi comedi0: driver 
ni_pcimio does not support attach using comedi_config" multiple times as 
well as a few comedi_fc errors regarding unkown symbols. Let me know if 
you'd like me to send over the full dmesg output, but it is quite large. 
Let me know if any further information is required, as I'm quite new to 
this.

Thanks!

-- 
You received this message because you are subscribed to the Google Groups "Comedi: Linux Control and Measurement Device Interface" group.
To unsubscribe from this group and stop receiving emails from it, send an email to [email protected].
To view this discussion on the web visit https://groups.google.com/d/msgid/comedi_list/25b0e8bf-21bc-4d46-a2ea-9f7a873d19b3n%40googlegroups.com.

------=_Part_7121_981152476.1688084972410
Content-Type: text/html; charset="UTF-8"
Content-Transfer-Encoding: quoted-printable

Hello everyone,<br /><br />I'm using a National Instruments PCI-6014 188626=
D-01 daq and trying to run comedi_config to setup the daq. Initially, I kep=
t getting the "comedi.o not loaded" error and fixed it by setting autoconfi=
g=3D0. However now, I'm getting the following error:<br /><br />configuring=
 driver=3Dni_pcimio 0,0,0,0,0,...0,0,0<br /><div>Configure failed!: Input/o=
utput error</div><div>Check kernel log for more information</div><div>Possi=
ble reasons for failure:</div><div>=C2=A0 Driver not found<br /><br />If I =
check kernel logs using "dmesg", I see: "comedi comedi0: driver ni_pcimio d=
oes not support attach using comedi_config" multiple times as well as a few=
 comedi_fc errors regarding unkown symbols. Let me know if you'd like me to=
 send over the full dmesg output, but it is quite large. Let me know if any=
 further information is required, as I'm quite new to this.<br /><br />Than=
ks!<br /></div>

<p></p>

-- <br />
You received this message because you are subscribed to the Google Groups &=
quot;Comedi: Linux Control and Measurement Device Interface&quot; group.<br=
 />
To unsubscribe from this group and stop receiving emails from it, send an e=
mail to <a href=3D"mailto:[email protected]">comedi_=
[email protected]</a>.<br />
To view this discussion on the web visit <a href=3D"https://groups.google.c=
om/d/msgid/comedi_list/25b0e8bf-21bc-4d46-a2ea-9f7a873d19b3n%40googlegroups=
.com?utm_medium=3Demail&utm_source=3Dfooter">https://groups.google.com/d/ms=
gid/comedi_list/25b0e8bf-21bc-4d46-a2ea-9f7a873d19b3n%40googlegroups.com</a=
>.<br />

------=_Part_7121_981152476.1688084972410--

------=_Part_7120_731089079.1688084972410--