Re: dectalk with Zabbly?

I am not sure what you guys are up to  but if it helps, here is a udev 
rule that I think will load the DECtalk module for your DECtalk USB when 
you plug it in. Note: It matches the tty subsystem instead of USB 
because that way you can use "%k" to point Speakup at the device. Also,  
it sets action = add so that the rule is triggered only once. I have 
similar rules for my TripleTalk and for my Raspberry Pi synths.

=== begin

ACTION=="add", \
SUBSYSTEM=="tty", \
ATTRS{idVendor}=="0dd0", \
ATTRS{idProduct}=="2001", \
RUN+="/sbin/modprobe speakup_dectlk tty=%k"
=== end


On 2/8/26 3:45 PM, Chime Hart wrote:
> OK Samuel, this is 90lines, hope it makes it through
> sudo lsusb -v -d 0dd0:2001
>
> Bus 005 Device 004: ID 0dd0:2001 Access Solutions DECtalk USB
> Negotiated speed: Full Speed (12Mbps)
> Device Descriptor:
>    bLength                18
>    bDescriptorType         1
>    bcdUSB               1.00
>    bDeviceClass            0 [unknown]
>    bDeviceSubClass         0 [unknown]
>    bDeviceProtocol         0
>    bMaxPacketSize0        64
>    idVendor           0x0dd0 Access Solutions
>    idProduct          0x2001 DECtalk USB
>    bcdDevice            2.06
>    iManufacturer           1 Access Solutions
>    iProduct                2 DECtalk USB
>    iSerial                 0
>    bNumConfigurations      1
>    Configuration Descriptor:
>      bLength                 9
>      bDescriptorType         2
>      wTotalLength       0x0035
>      bNumInterfaces          1
>      bConfigurationValue     1
>      iConfiguration          0
>      bmAttributes         0xa0
>        (Bus Powered)
>        Remote Wakeup
>      MaxPower              400mA
>      Interface Descriptor:
>        bLength                 9
>        bDescriptorType         4
>        bInterfaceNumber        0
>        bAlternateSetting       0
>        bNumEndpoints           5
>        bInterfaceClass       255 Vendor Specific Class
>        bInterfaceSubClass      0 [unknown]
>        bInterfaceProtocol      0
>        iInterface              0
>        Endpoint Descriptor:
>          bLength                 7
>          bDescriptorType         5
>          bEndpointAddress     0x02  EP 2 OUT
>          bmAttributes            3
>            Transfer Type            Interrupt
>            Synch Type               None
>            Usage Type               Data
>          wMaxPacketSize     0x0040  1x 64 bytes
>          bInterval               1
>        Endpoint Descriptor:
>          bLength                 7
>          bDescriptorType         5
>          bEndpointAddress     0x04  EP 4 OUT
>          bmAttributes            3
>            Transfer Type            Interrupt
>            Synch Type               None
>            Usage Type               Data
>          wMaxPacketSize     0x0040  1x 64 bytes
>          bInterval               1
>        Endpoint Descriptor:
>          bLength                 7
>          bDescriptorType         5
>          bEndpointAddress     0x06  EP 6 OUT
>          bmAttributes            3
>            Transfer Type            Interrupt
>            Synch Type               None
>            Usage Type               Data
>          wMaxPacketSize     0x0040  1x 64 bytes
>          bInterval               1
>        Endpoint Descriptor:
>          bLength                 7
>          bDescriptorType         5
>          bEndpointAddress     0x86  EP 6 IN
>          bmAttributes            3
>            Transfer Type            Interrupt
>            Synch Type               None
>            Usage Type               Data
>          wMaxPacketSize     0x0040  1x 64 bytes
>          bInterval               1
>        Endpoint Descriptor:
>          bLength                 7
>          bDescriptorType         5
>          bEndpointAddress     0x84  EP 4 IN
>          bmAttributes            3
>            Transfer Type            Interrupt
>            Synch Type               None
>            Usage Type               Data
>          wMaxPacketSize     0x0040  1x 64 bytes
>          bInterval               1
> Device Status:     0x0000
>    (Bus Powered)
> Chime
>
>