Re: problem configuring squeeze

Hello,

On Sun, 15 May 2011 17:16:47 +0200
Eugen Leitl <[email protected]> wrote:

> You were correct, IPv6 autoconfiguration was the culprit.
> It is very annoying to switch off, I had to use the 
> recipe from https://tools.bitfolk.com/wiki/IPv6
> 
> What worked for me (from /etc/network/interfaces ):
> 
> # WAN IPv6 from 2a01:4f8:7d:300::/56
> iface eth0 inet6 static
> address 2a01:4f8:7d:300::2
> gateway 2a01:4f8:7d:300::1
> netmask 64
> # Disable autoconf
> post-up echo 0 > /proc/sys/net/ipv6/conf/default/accept_ra
> post-up echo 0 > /proc/sys/net/ipv6/conf/all/accept_ra
> post-up echo 0 > /proc/sys/net/ipv6/conf/$IFACE/accept_ra
> post-up echo 0 > /proc/sys/net/ipv6/conf/default/autoconf
> post-up echo 0 > /proc/sys/net/ipv6/conf/all/autoconf
> post-up echo 0 > /proc/sys/net/ipv6/conf/$IFACE/autoconf

Newer ifupdown can do this automagically. Soon to appear in
experimental.

-- 
WBR, Andrew

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
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=qwVC
-----END PGP SIGNATURE-----