Bug#1111027: linux-image-6.12.38+deb13-amd64: HP Gen8: Crashing with 6.12 from trixie, NMI error in IML logs

Package: src:linux
Version: 6.12.38-1
Severity: normal
X-Debbugs-Cc: [email protected]
User: [email protected]
Usertags: amd64

Dear Maintainer,

after upgrading to trixie, the HP Microserver Gen8 started to crash
randomly, hard, to system error (blinking red light in the front, not
recoverable with reset but only removing power, IPMI/ILO still usable though).

No dmesg/stacktrace visible.

IML (Integrated Management Log from ILO) says:

Unrecoverable System Error (NMI) has occurred.  System Firmware will log additional details in a separate IML entry if possible

(no additional information can be found)

This can happen within half an hour after boot or 12 hours later, so
debugging might be a little hard. I rolled back to the bookworm kernel
and it has been running stable for 20 hours now.

I found somewhat related bugs (#898336, #995773) with NMI stacktraces mentioning the wdt
module - this isn't loaded in 6.1, haven't booted 6.12 again to check.
Also haven't tried fiddling with boot options, since it takes ages to
reproduce.

I'm running iLO 4 2.82 since 2023 - which is the latest firmware to my
knowledge.

-- Package-specific info:
** Kernel log: boot messages should be attached

** Model information
sys_vendor: HP
product_name: ProLiant MicroServer Gen8
product_version: 
chassis_vendor: HP
chassis_version: 
bios_vendor: HP
bios_version: J06

** Configuration for modprobe:
blacklist microcode
blacklist arkfb
blacklist aty128fb
blacklist atyfb
blacklist radeonfb
blacklist cirrusfb
blacklist cyber2000fb
blacklist kyrofb
blacklist matroxfb_base
blacklist mb862xxfb
blacklist neofb
blacklist pm2fb
blacklist pm3fb
blacklist s3fb
blacklist savagefb
blacklist sisfb
blacklist tdfxfb
blacklist tridentfb
blacklist vt8623fb
blacklist microcode
options snd_pcsp index=-2
options cx88_alsa index=-2
options snd_atiixp_modem index=-2
options snd_intel8x0m index=-2
options snd_via82xx_modem index=-2
options md_mod start_ro=1
options bonding max_bonds=0
options dummy numdummies=0
options ifb numifbs=0

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/Ivy Bridge DRAM Controller [8086:0158] (rev 09)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: ie31200_edac
	Kernel modules: ie31200_edac

00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:0151] (rev 09) (prog-if 00 [Normal decode])
	Subsystem: Hewlett-Packard Company Device [103c:330b]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 24
	Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
	I/O behind bridge: [disabled] [16-bit]
	Memory behind bridge: fbf00000-fbffffff [size=1M] [32-bit]
	Prefetchable memory behind bridge: [disabled] [64-bit]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:06.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:015d] (rev 09) (prog-if 00 [Normal decode])
	Subsystem: Hewlett-Packard Company Device [103c:330b]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 25
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: [disabled] [16-bit]
	Memory behind bridge: fbd00000-fbdfffff [size=1M] [32-bit]
	Prefetchable memory behind bridge: c0000000-dfffffff [size=512M] [32-bit]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Device [103c:330d]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 21
	Region 0: Memory at facf0000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci

00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
	Subsystem: Hewlett-Packard Company Device [103c:330d]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0
	I/O behind bridge: [disabled] [16-bit]
	Memory behind bridge: [disabled] [32-bit]
	Prefetchable memory behind bridge: [disabled] [64-bit]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5) (prog-if 00 [Normal decode])
	Subsystem: Hewlett-Packard Company Device [103c:330d]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	I/O behind bridge: [disabled] [16-bit]
	Memory behind bridge: bc000000-bc0fffff [size=1M] [32-bit]
	Prefetchable memory behind bridge: fab00000-fabfffff [size=1M] [32-bit]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.6 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 [8086:1c1c] (rev b5) (prog-if 00 [Normal decode])
	Subsystem: Hewlett-Packard Company Device [103c:330d]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin C routed to IRQ 18
	Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
	I/O behind bridge: [disabled] [16-bit]
	Memory behind bridge: fbe00000-fbefffff [size=1M] [32-bit]
	Prefetchable memory behind bridge: [disabled] [64-bit]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.7 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 [8086:1c1e] (rev b5) (prog-if 00 [Normal decode])
	Subsystem: Hewlett-Packard Company Device [103c:330d]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin D routed to IRQ 19
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 3000-3fff [size=4K] [16-bit]
	Memory behind bridge: fad00000-fbcfffff [size=16M] [32-bit]
	Prefetchable memory behind bridge: bf000000-bfffffff [size=16M] [32-bit]
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA- VGA+ VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Device [103c:330d]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 20
	Region 0: Memory at face0000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a5) (prog-if 01 [Subtractive decode])
	Subsystem: Hewlett-Packard Company Device [103c:330d]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=14, subordinate=14, sec-latency=32
	I/O behind bridge: [disabled] [16-bit]
	Memory behind bridge: [disabled] [32-bit]
	Prefetchable memory behind bridge: [disabled] [64-bit]
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation C204 Chipset LPC Controller [8086:1c54] (rev 05)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: lpc_ich
	Kernel modules: lpc_ich

00:1f.2 RAID bus controller [0104]: Intel Corporation 6 Series/C200 Series Desktop SATA RAID Controller [8086:1c04] (rev 05)
	Subsystem: Hewlett Packard Enterprise Device [1590:006c]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 26
	Region 0: I/O ports at 10c0 [size=8]
	Region 1: I/O ports at 10c8 [size=4]
	Region 2: I/O ports at 10d0 [size=8]
	Region 3: I/O ports at 10d8 [size=4]
	Region 4: I/O ports at 10e0 [size=32]
	Region 5: Memory at facd0000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ahci
	Kernel modules: ahci

01:00.0 System peripheral [0880]: Hewlett-Packard Company Integrated Lights-Out Standard Slave Instrumentation & System Support [103c:3306] (rev 05)
	Subsystem: Hewlett-Packard Company iLO4 [103c:3381]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at 3000 [size=256]
	Region 1: Memory at fbcf0000 (32-bit, non-prefetchable) [size=512]
	Region 2: I/O ports at 3400 [size=256]
	Capabilities: <access denied>
	Kernel modules: hpwdt

01:00.1 VGA compatible controller [0300]: Matrox Electronics Systems Ltd. MGA G200EH [102b:0533] (prog-if 00 [VGA controller])
	Subsystem: Hewlett-Packard Company iLO4 [103c:3381]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 16
	Region 0: Memory at bf000000 (32-bit, prefetchable) [size=16M]
	Region 1: Memory at fbce0000 (32-bit, non-prefetchable) [size=16K]
	Region 2: Memory at fb000000 (32-bit, non-prefetchable) [size=8M]
	Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: mgag200
	Kernel modules: mgag200

01:00.2 System peripheral [0880]: Hewlett-Packard Company Integrated Lights-Out Standard Management Processor Support and Messaging [103c:3307] (rev 05)
	Subsystem: Hewlett-Packard Company iLO4 [103c:3381]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 16
	Region 0: I/O ports at 3800 [size=256]
	Region 1: Memory at faff0000 (32-bit, non-prefetchable) [size=256]
	Region 2: Memory at fae00000 (32-bit, non-prefetchable) [size=1M]
	Region 3: Memory at fad80000 (32-bit, non-prefetchable) [size=512K]
	Region 4: Memory at fad70000 (32-bit, non-prefetchable) [size=32K]
	Region 5: Memory at fad60000 (32-bit, non-prefetchable) [size=32K]
	Expansion ROM at fad00000 [virtual] [disabled] [size=64K]
	Capabilities: <access denied>
	Kernel driver in use: hpilo
	Kernel modules: hpilo

01:00.4 USB controller [0c03]: Hewlett-Packard Company Integrated Lights-Out Standard Virtual USB Controller [103c:3300] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Hewlett-Packard Company iLO4 [103c:3381]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 35
	Region 4: I/O ports at 3c00 [size=32]
	Capabilities: <access denied>
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci_hcd

02:00.0 Memory controller [0580]: Hewlett Packard Enterprise Device [1590:005f]
	DeviceName: Memory Controller
	Subsystem: Hewlett Packard Enterprise Device [1590:005f]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at c0000000 (64-bit, prefetchable) [size=512M]
	Region 2: Memory at fbdf0000 (64-bit, non-prefetchable) [size=32K]
	Capabilities: <access denied>

03:00.0 Ethernet controller [0200]: Broadcom Inc. and subsidiaries NetXtreme BCM5720 Gigabit Ethernet PCIe [14e4:165f]
	DeviceName: NIC Port 1
	Subsystem: Hewlett-Packard Company NC332i Adapter [103c:2133]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at fabf0000 (64-bit, prefetchable) [size=64K]
	Region 2: Memory at fabe0000 (64-bit, prefetchable) [size=64K]
	Region 4: Memory at fabd0000 (64-bit, prefetchable) [size=64K]
	Expansion ROM at bc000000 [virtual] [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: tg3
	Kernel modules: tg3

03:00.1 Ethernet controller [0200]: Broadcom Inc. and subsidiaries NetXtreme BCM5720 Gigabit Ethernet PCIe [14e4:165f]
	DeviceName: NIC Port 2
	Subsystem: Hewlett-Packard Company NC332i Adapter [103c:2133]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at fabc0000 (64-bit, prefetchable) [size=64K]
	Region 2: Memory at fabb0000 (64-bit, prefetchable) [size=64K]
	Region 4: Memory at faba0000 (64-bit, prefetchable) [size=64K]
	Expansion ROM at bc020000 [virtual] [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: tg3
	Kernel modules: tg3

04:00.0 USB controller [0c03]: Renesas Electronics Corp. uPD720201 USB 3.0 Host Controller [1912:0014] (rev 03) (prog-if 30 [XHCI])
	Subsystem: Hewlett-Packard Company Device [103c:1996]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at fbef0000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci

07:00.0 USB controller [0c03]: ASMedia Technology Inc. ASM2142/ASM3142 USB 3.1 Host Controller [1b21:2142] (prog-if 30 [XHCI])
	Subsystem: Post Impression Systems. Device [3142:1b21]
	Physical Slot: 1
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at fbff0000 (64-bit, non-prefetchable) [size=32K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci


** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 003: ID 13fe:1d00 Phison Electronics Corp. DataTraveler 2.0 1GB/4GB Flash Drive / Patriot Xporter 4GB Flash Drive
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 2109:2822 VIA Labs, Inc. USB2.0 Hub             
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 002: ID 2109:0822 VIA Labs, Inc. USB3.1 Hub             
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 003: ID 0424:2660 Microchip Technology, Inc. (formerly SMSC) Hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 003: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub
Bus 005 Device 004: ID 8564:1000 Transcend Information, Inc. JetFlash
Bus 005 Device 005: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub
Bus 005 Device 006: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub
Bus 005 Device 007: ID 1cf1:0030 Dresden Elektronik ZigBee gateway [ConBee II]
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 007 Device 002: ID 0bda:0411 Realtek Semiconductor Corp. Hub
Bus 007 Device 003: ID 0bda:0411 Realtek Semiconductor Corp. Hub
Bus 007 Device 004: ID 0bda:0411 Realtek Semiconductor Corp. Hub


-- System Information:
Debian Release: 13.0
  APT prefers stable-updates
  APT policy: (500, 'stable-updates'), (500, 'stable-security'), (500, 'stable'), (500, 'oldstable')
Architecture: amd64 (x86_64)

Kernel: Linux 6.1.0-35-amd64 (SMP w/8 CPU threads; PREEMPT)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8), LANGUAGE not set
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled

Versions of packages linux-image-6.12.38+deb13-amd64 depends on:
ii  initramfs-tools [linux-initramfs-tool]  0.148.3
ii  kmod                                    34.2-2
ii  linux-base                              4.12

Versions of packages linux-image-6.12.38+deb13-amd64 recommends:
ii  apparmor  4.1.0-1

Versions of packages linux-image-6.12.38+deb13-amd64 suggests:
pn  debian-kernel-handbook  <none>
ii  firmware-linux-free     20241210-2
ii  grub-pc                 2.12-9
pn  linux-doc-6.12          <none>

Versions of packages linux-image-6.12.38+deb13-amd64 is related to:
ii  firmware-amd-graphics      20250410-2
pn  firmware-atheros           <none>
pn  firmware-bnx2              <none>
pn  firmware-bnx2x             <none>
pn  firmware-brcm80211         <none>
pn  firmware-cavium            <none>
pn  firmware-cirrus            <none>
ii  firmware-intel-graphics    20250410-2
ii  firmware-intel-misc        20250410-2
pn  firmware-intel-sound       <none>
pn  firmware-ipw2x00           <none>
pn  firmware-ivtv              <none>
pn  firmware-iwlwifi           <none>
pn  firmware-libertas          <none>
pn  firmware-marvell-prestera  <none>
ii  firmware-mediatek          20250410-2
ii  firmware-misc-nonfree      20250410-2
pn  firmware-myricom           <none>
pn  firmware-netronome         <none>
pn  firmware-netxen            <none>
ii  firmware-nvidia-graphics   20250410-2
pn  firmware-qcom-soc          <none>
pn  firmware-qlogic            <none>
pn  firmware-realtek           <none>
pn  firmware-samsung           <none>
pn  firmware-siano             <none>
pn  firmware-ti-connectivity   <none>
pn  xen-hypervisor             <none>

-- no debconf information