Re: Диску скоро капут?
artiom <[email protected]>
| Newsgroups | gmane.linux.debian.user.russian |
|---|---|
| Message-ID | <[email protected]> |
17.06.2021 01:03, sergio пишет:
> SMART в студию.
> И прогоните все тесты перед этим smartctl -t {short|long|conveyance}
> /dev/sdX
>
smartctl -a /dev/sda
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-16-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST1000LM035-1RK172
Serial Number:
LU WWN Device Id:
Firmware Version: SDM1
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Jun 17 19:54:18 2021 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 168) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 055 040 006 Pre-fail
Always - 195148675
3 Spin_Up_Time 0x0003 099 099 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age
Always - 2594
5 Reallocated_Sector_Ct 0x0033 070 069 036 Pre-fail
Always - 19880
7 Seek_Error_Rate 0x000f 088 060 045 Pre-fail
Always - 644435338
9 Power_On_Hours 0x0032 075 075 000 Old_age
Always - 22484 (119 0 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age
Always - 2249
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always
- 437
188 Command_Timeout 0x0032 100 097 000 Old_age Always
- 236227395654
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 059 039 040 Old_age Always
In_the_past 41 (Min/Max 39/50 #7)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 195
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 140
193 Load_Cycle_Count 0x0032 062 062 000 Old_age Always
- 77186
194 Temperature_Celsius 0x0022 041 061 000 Old_age Always
- 41 (0 13 0 0 0)
197 Current_Pending_Sector 0x0012 096 090 000 Old_age Always
- 344
198 Offline_Uncorrectable 0x0010 096 090 000 Old_age
Offline - 344
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age
Offline - 22279 (64 40 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age
Offline - 23821699901
242 Total_LBAs_Read 0x0000 100 253 000 Old_age
Offline - 39392795114
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always
- 0
SMART Error Log Version: 1
ATA Error Count: 437 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 437 occurred at disk power-on lifetime: 22464 hours (936 days + 0
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 13:10:13.272 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 13:10:13.262 SET FEATURES [Enable SATA
feature]
27 00 00 00 00 00 e0 00 13:10:13.236 READ NATIVE MAX ADDRESS
EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 13:10:13.234 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 13:10:13.222 SET FEATURES [Set transfer
mode]
Error 436 occurred at disk power-on lifetime: 22464 hours (936 days + 0
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 13:10:13.038 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 13:10:13.009 SET FEATURES [Enable SATA
feature]
27 00 00 00 00 00 e0 00 13:10:12.982 READ NATIVE MAX ADDRESS
EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 13:10:12.981 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 13:10:12.968 SET FEATURES [Set transfer
mode]
Error 435 occurred at disk power-on lifetime: 22464 hours (936 days + 0
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 13:10:12.821 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 13:10:12.811 SET FEATURES [Enable SATA
feature]
27 00 00 00 00 00 e0 00 13:10:12.785 READ NATIVE MAX ADDRESS
EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 13:10:12.783 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 13:10:12.771 SET FEATURES [Set transfer
mode]
Error 434 occurred at disk power-on lifetime: 22464 hours (936 days + 0
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 13:10:12.571 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 13:10:12.547 SET FEATURES [Enable SATA
feature]
27 00 00 00 00 00 e0 00 13:10:12.520 READ NATIVE MAX ADDRESS
EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 13:10:12.519 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 13:10:12.506 SET FEATURES [Set transfer
mode]
Error 433 occurred at disk power-on lifetime: 22464 hours (936 days + 0
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 13:10:12.370 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 13:10:12.361 SET FEATURES [Enable SATA
feature]
27 00 00 00 00 00 e0 00 13:10:12.334 READ NATIVE MAX ADDRESS
EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 13:10:12.332 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 13:10:12.320 SET FEATURES [Set transfer
mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 22482
-
# 2 Conveyance offline Completed without error 00% 22468
-
# 3 Extended offline Completed: read failure 90% 22466
255872552
# 4 Extended offline Completed: read failure 90% 13732
430032136
# 5 Short offline Completed without error 00% 6
-
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.