Re: aacraid and large memory problem (2.6.0-test11)
Mark Haverkamp <[email protected]> Wed, 03 Dec 2003 15:25:45 -0800
| Newsgroups | gmane.linux.drivers.aacraid.devel,gmane.linux.kernel |
|---|---|
| Message-ID | <[email protected]> |
On Wed, 2003-12-03 at 14:28, Kevin Fenzi wrote: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > >>>>> "Mark" == Mark Haverkamp <[email protected]> writes: > > Mark> I set up my machine to boot on the aacraid disk and it booted OK > Mark> for me. Maybe its a problem with a particular model? > > Mark> lspci on mine says: > > Mark> 02:04.0 RAID bus controller: Digital Equipment Corporation > Mark> DECchip 21554 (rev 01) Subsystem: Adaptec Adaptec 5400S > > This one says: > > 05:01.0 RAID bus controller: Adaptec AAC-RAID (rev 01) > Subsystem: Adaptec AAC-RAID > Flags: bus master, fast Back2Back, 66Mhz, slow devsel, latency 64, IRQ 96 > Memory at f8000000 (32-bit, prefetchable) [size=64M] > Expansion ROM at <unassigned> [disabled] [size=64K] > Capabilities: [80] Power Management version 2 > > It's a 2200S controller. > bios version 6008 > Could you try this patch? I took the code from the adaptec version of the driver. It fiddles with the dma mask on the 2200S controller among others. Mark. ===== drivers/scsi/aacraid/aachba.c 1.20 vs edited ===== --- 1.20/drivers/scsi/aacraid/aachba.c Fri May 2 12:30:49 2003 +++ edited/drivers/scsi/aacraid/aachba.c Wed Dec 3 15:10:22 2003 @@ -525,6 +525,14 @@ if(dev->pae_support != 0) { printk(KERN_INFO"%s%d: 64 Bit PAE enabled\n", dev->name, dev->id); pci_set_dma_mask(dev->pdev, (dma_addr_t)0xFFFFFFFFFFFFFFFFULL); + } else { + /* + * Reset if Quirk 31 was used, since data + * transfers are ok. + */ + if (pci_set_dma_mask(dev->pdev, 0xFFFFFFFFULL)) { + printk(KERN_INFO"aacraid: Can't reset DMA mask.\n"); + } } fib_complete(fibptr); ===== drivers/scsi/aacraid/aacraid.h 1.9 vs edited ===== --- 1.9/drivers/scsi/aacraid/aacraid.h Wed Oct 22 02:52:43 2003 +++ edited/drivers/scsi/aacraid/aacraid.h Wed Dec 3 15:21:48 2003 @@ -529,6 +529,8 @@ char * vname; char * model; u16 channels; + int quirks; +#define AAC_QUIRK_31BIT 1 }; /* ===== drivers/scsi/aacraid/linit.c 1.22 vs edited ===== --- 1.22/drivers/scsi/aacraid/linit.c Tue Aug 26 09:25:41 2003 +++ edited/drivers/scsi/aacraid/linit.c Wed Dec 3 15:22:42 2003 @@ -86,36 +86,47 @@ * for the card. At that time we can remove the channels from here */ static struct aac_driver_ident aac_drivers[] = { - { 0x1028, 0x0001, 0x1028, 0x0001, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 2/Si */ - { 0x1028, 0x0002, 0x1028, 0x0002, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */ - { 0x1028, 0x0003, 0x1028, 0x0003, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Si */ - { 0x1028, 0x0004, 0x1028, 0x00d0, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Si */ - { 0x1028, 0x0002, 0x1028, 0x00d1, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */ - { 0x1028, 0x0002, 0x1028, 0x00d9, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */ - { 0x1028, 0x000a, 0x1028, 0x0106, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */ - { 0x1028, 0x000a, 0x1028, 0x011b, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */ - { 0x1028, 0x000a, 0x1028, 0x0121, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */ - { 0x9005, 0x0283, 0x9005, 0x0283, aac_rx_init, "aacraid", "ADAPTEC ", "catapult ", 2 }, /* catapult*/ - { 0x9005, 0x0284, 0x9005, 0x0284, aac_rx_init, "aacraid", "ADAPTEC ", "tomcat ", 2 }, /* tomcat*/ - { 0x9005, 0x0285, 0x9005, 0x0286, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2120S ", 1 }, /* Adaptec 2120S (Crusader)*/ - { 0x9005, 0x0285, 0x9005, 0x0285, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2200S ", 2 }, /* Adaptec 2200S (Vulcan)*/ - { 0x9005, 0x0285, 0x9005, 0x0287, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2200S ", 2 }, /* Adaptec 2200S (Vulcan-2m)*/ - { 0x9005, 0x0285, 0x17aa, 0x0286, aac_rx_init, "aacraid", "Legend ", "Legend S220 ", 1 }, /* Legend S220*/ - { 0x9005, 0x0285, 0x17aa, 0x0287, aac_rx_init, "aacraid", "Legend ", "Legend S230 ", 2 }, /* Legend S230*/ - - { 0x9005, 0x0285, 0x9005, 0x0288, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 3230S ", 2 }, /* Adaptec 3230S (Harrier)*/ - { 0x9005, 0x0285, 0x9005, 0x0289, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 3240S ", 2 }, /* Adaptec 3240S (Tornado)*/ - { 0x9005, 0x0285, 0x9005, 0x028a, aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2020S PCI-X ", 2 }, /* ASR-2020S PCI-X ZCR (Skyhawk)*/ - { 0x9005, 0x0285, 0x9005, 0x028b, aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2020S PCI-X ", 2 }, /* ASR-2020S SO-DIMM PCI-X ZCR(Terminator)*/ - { 0x9005, 0x0285, 0x9005, 0x0290, aac_rx_init, "aacraid", "ADAPTEC ", "AAR-2410SA SATA ", 2 }, /* AAR-2410SA PCI SATA 4ch (Jaguar II)*/ - { 0x9005, 0x0250, 0x1014, 0x0279, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec ", 2 }, /* (Marco)*/ - { 0x9005, 0x0250, 0x1014, 0x028c, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec ", 2 }, /* (Sebring)*/ + { 0x1028, 0x0001, 0x1028, 0x0001, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 2/Si (Iguana/PERC2Si) */ + { 0x1028, 0x0002, 0x1028, 0x0002, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Opal/PERC3Di) */ + { 0x1028, 0x0003, 0x1028, 0x0003, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Si (SlimFast/PERC3Si */ + { 0x1028, 0x0004, 0x1028, 0x00d0, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Iguana FlipChip/PERC3DiF */ + { 0x1028, 0x0002, 0x1028, 0x00d1, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Viper/PERC3DiV) */ + { 0x1028, 0x0002, 0x1028, 0x00d9, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Lexus/PERC3DiL) */ + { 0x1028, 0x000a, 0x1028, 0x0106, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 1, AAC_QUIRK_31BIT }, /* PERC 3/Di (Jaguar/PERC3DiJ) */ + { 0x1028, 0x000a, 0x1028, 0x011b, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Dagger/PERC3DiD) */ + { 0x1028, 0x000a, 0x1028, 0x0121, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Boxster/PERC3DiB) */ + { 0x9005, 0x0283, 0x9005, 0x0283, aac_rx_init, "aacraid", "ADAPTEC ", "catapult ", 2, AAC_QUIRK_31BIT }, /* catapult */ + { 0x9005, 0x0284, 0x9005, 0x0284, aac_rx_init, "aacraid", "ADAPTEC ", "tomcat ", 2, AAC_QUIRK_31BIT }, /* tomcat */ + { 0x9005, 0x0285, 0x9005, 0x0286, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2120S ", 1, AAC_QUIRK_31BIT }, /* Adaptec 2120S (Crusader) */ + { 0x9005, 0x0285, 0x9005, 0x0285, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2200S ", 2, AAC_QUIRK_31BIT }, /* Adaptec 2200S (Vulcan) */ + { 0x9005, 0x0285, 0x9005, 0x0287, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2200S ", 2, AAC_QUIRK_31BIT }, /* Adaptec 2200S (Vulcan-2m) */ + { 0x9005, 0x0285, 0x17aa, 0x0286, aac_rx_init, "aacraid", "Legend ", "Legend S220 ", 1, AAC_QUIRK_31BIT }, /* Legend S220 (Legend Crusader) */ + { 0x9005, 0x0285, 0x17aa, 0x0287, aac_rx_init, "aacraid", "Legend ", "Legend S230 ", 2, AAC_QUIRK_31BIT }, /* Legend S230 (Legend Vulcan) */ + + { 0x9005, 0x0285, 0x9005, 0x0288, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 3230S ", 2 }, /* Adaptec 3230S (Harrier) */ + { 0x9005, 0x0285, 0x9005, 0x0289, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 3240S ", 2 }, /* Adaptec 3240S (Tornado) */ + { 0x9005, 0x0285, 0x9005, 0x028a, aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2020S PCI-X ", 2 }, /* ASR-2020S PCI-X ZCR (Skyhawk) */ + { 0x9005, 0x0285, 0x9005, 0x028b, aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2020S PCI-X ", 2 }, /* ASR-2020S SO-DIMM PCI-X ZCR (Terminator) */ +/* { 0x9005, 0x0286, 0x9005, 0x028c, aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2230S PCI-X ", 2 }, */ /* ASR-2230S PCI-X (Lancer pre-production) */ + { 0x9005, 0x0285, 0x9005, 0x0290, aac_rx_init, "aacraid", "ADAPTEC ", "AAR-2410SA SATA ", 1 }, /* AAR-2410SA PCI SATA 4ch (Jaguar II) */ + { 0x9005, 0x0285, 0x1028, 0x0291, aac_rx_init, "aacraid", "DELL ", "CERC SR2 ", 1 }, /* CERC SATA RAID 2 PCI SATA 6ch (DellCorsair) */ + { 0x9005, 0x0285, 0x9005, 0x0292, aac_rx_init, "aacraid", "ADAPTEC ", "AAR-2810SA SATA ", 1 }, /* AAR-2810SA PCI SATA 8ch (Corsair-8) */ + { 0x9005, 0x0285, 0x9005, 0x0293, aac_rx_init, "aacraid", "ADAPTEC ", "AAR-21610SA SATA", 1 }, /* AAR-21610SA PCI SATA 16ch (Corsair-16) */ + { 0x9005, 0x0285, 0x9005, 0x0294, aac_rx_init, "aacraid", "ADAPTEC ", "SO-DIMM SATA ZCR", 1 }, /* ESD SO-DIMM PCI-X SATA ZCR (Prowler) */ + { 0x9005, 0x0285, 0x0E11, 0x0295, aac_rx_init, "aacraid", "ADAPTEC ", "SATA 6Channel ", 1 }, /* SATA 6Ch (Bearcat) */ - { 0x9005, 0x0285, 0x1028, 0x0287, aac_rx_init, "percraid", "DELL ", "PERC 320/DC ", 2 }, /* Perc 320/DC*/ + { 0x9005, 0x0285, 0x1028, 0x0287, aac_rx_init, "percraid", "DELL ", "PERC 320/DC ", 2, AAC_QUIRK_31BIT }, /* Perc 320/DC*/ { 0x1011, 0x0046, 0x9005, 0x0365, aac_sa_init, "aacraid", "ADAPTEC ", "Adaptec 5400S ", 4 }, /* Adaptec 5400S (Mustang)*/ { 0x1011, 0x0046, 0x9005, 0x0364, aac_sa_init, "aacraid", "ADAPTEC ", "AAC-364 ", 4 }, /* Adaptec 5400S (Mustang)*/ - { 0x1011, 0x0046, 0x9005, 0x1364, aac_sa_init, "percraid", "DELL ", "PERCRAID ", 4 }, /* Dell PERC2 "Quad Channel" */ - { 0x1011, 0x0046, 0x103c, 0x10c2, aac_sa_init, "hpnraid", "HP ", "NetRAID ", 4 } /* HP NetRAID-4M */ + { 0x1011, 0x0046, 0x9005, 0x1364, aac_sa_init, "percraid", "DELL ", "PERCRAID ", 4, AAC_QUIRK_31BIT }, /* Dell PERC2/QC */ + { 0x1011, 0x0046, 0x103c, 0x10c2, aac_sa_init, "hpnraid", "HP ", "NetRAID ", 4 }, /* HP NetRAID-4M */ + + { 0x9005, 0x0285, 0x1028, PCI_ANY_ID, + aac_rx_init, "aacraid", "DELL ", "RAID ", 2, AAC_QUIRK_31BIT }, /* Dell Catchall */ + { 0x9005, 0x0285, 0x17aa, PCI_ANY_ID, + aac_rx_init, "aacraid", "Legend ", "RAID ", 2, AAC_QUIRK_31BIT }, /* Legend Catchall */ + { 0x9005, 0x0285, PCI_ANY_ID, PCI_ANY_ID, + aac_rx_init, "aacraid", "ADAPTEC ", "RAID ", 2, AAC_QUIRK_31BIT }, /* Adaptec Catch All */ }; #define NUM_AACTYPES (sizeof(aac_drivers) / sizeof(struct aac_driver_ident)) @@ -174,6 +185,7 @@ struct aac_dev *aac; struct fsa_scsi_hba *fsa_dev_ptr; char *name = NULL; + int ret; printk(KERN_INFO "Red Hat/Adaptec aacraid driver (%s %s)\n", AAC_DRIVER_VERSION, AAC_DRIVER_BUILD_DATE); @@ -194,7 +206,15 @@ if (pci_enable_device(dev)) continue; pci_set_master(dev); - pci_set_dma_mask(dev, 0xFFFFFFFFULL); + if (aac_drivers[index].quirks & AAC_QUIRK_31BIT) + ret = pci_set_dma_mask(dev, 0x7FFFFFFFULL); + else + ret = pci_set_dma_mask(dev, 0xFFFFFFFFULL); + + if (ret) { + printk(KERN_WARNING "aacraid: Can't set DMA mask.\n"); + continue; + } if((dev->subsystem_vendor != aac_drivers[index].subsystem_vendor) || (dev->subsystem_device != aac_drivers[index].subsystem_device)) -- Mark Haverkamp <[email protected]> _______________________________________________ Linux-aacraid-devel mailing list [email protected] http://lists.us.dell.com/mailman/listinfo/linux-aacraid-devel Please read the FAQ at http://lists.us.dell.com/faq or search the list archives at http://lists.us.dell.com/htdig/