Re: FC4 and F5D6050 problem....

Hello,

if I make abstraction that I have another linux distro and another wireless card (well it sounds
like a good introduction at this hour :)... ) the ony difference I can see is that you're using
the ohci driver. you sould try with uhci and see if it makes a difference, especially if your
computer has a recently Intel chipset.

Here is a quick description off the two:
http://lists.digium.com/pipermail/asterisk-users/2003-January/007143.html

Hope it helps...

--- Jeff volckaert <[email protected]> wrote:

> Hello Everybody,
> 
> I have a Belkin F5D6050 connected to a Fedora Core 4 box running
> kernel  2.6.12-1.1390_FC4.  I just installed yesterdays CVS tarball
> and am trying to get my Axim handheld to connect to the internet.  It
> seems to connect, but I cannot ping the handheld's IP.  Also, the 'TX
> packets:2' from ifconfig looks strange.  Shouldn't it be trasmitting
> more?
> 
> I use the commands 'iwconfig wlan0 mode ad-hoc channel 10 essid
> mqtlan2' and 'ifconfig wlan0 192.168.1.20' to setup the wireless
> network.
> 
> Here's the output from iwconfig and ifconfig:
> 
> wlan0     IEEE 802.11-DS  ESSID:"mqtlan2"  Nickname:"okuwlan"
>           Mode:Ad-Hoc  Frequency:2.457 GHz  Cell: 02:00:B9:D6:1F:00
>           Bit Rate:11 Mb/s   Tx-Power=15 dBm
>           Retry limit:8   RTS thr=1536 B   Fragment thr=1536 B
>           Encryption key:off
>           Power Management:off
>           Link Quality:0/0  Signal level:55/255  Noise level:0/0
>           Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
>           Tx excessive retries:0  Invalid misc:0   Missed beacon:0
> 
> 
> wlan0     Link encap:Ethernet  HWaddr 00:30:BD:60:80:75
>           inet addr:192.168.1.20  Bcast:192.168.1.255  Mask:255.255.255.0
>           inet6 addr: fe80::230:bdff:fe60:8075/64 Scope:Link
>           UP BROADCAST  MTU:1500  Metric:1
>           RX packets:56 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:1000
>           RX bytes:4500 (4.3 KiB)  TX bytes:168 (168.0 b)
> 
> Here's the output from my log:
> kernel: usb 1-2: new full speed USB device using ohci_hcd and address 4
> kernel: /root/at76c503a/at76c503.c: $Id: at76c503.c,v 1.74 2005/03/08
> 01:33:14 jal2 Exp $ compiled Jul 11 2005 19:01:57
> kernel: /root/at76c503a/at76c503.c: firmware version 8.101.5 #84 (fcs_len 4)
> kernel: /root/at76c503a/at76c503.c: device's MAC 00:30:bd:60:80:75,
> regulatory domain FCC (U.S) (id 16)
> kernel: /root/at76c503a/at76c503.c: registered wlan0
> 
> Any help?
> 
> BTW, this was working under FC3.  I don't know if FC4 or kernel 2.6.12
> changed anything.
> 
> Jeff
> _______________________________________________
> at76c503a-user mailing list
> [email protected]
> http://lists.berlios.de/mailman/listinfo/at76c503a-user
> 


--------------------------------
I must not fear.
Fear is the mind-killer.
Fear is the little-death that brings total obliteration.
I will face my fear.
I will permit it to pass over me and through me.
And when it has gone past I will turn the inner eye to see its path.
Where the fear has gone there will be nothing.
Only I will remain.
--------------------------------


		
____________________________________________________
Start your day with Yahoo! - make it your home page
http://www.yahoo.com/r/hs