Re: Now no access point found (Re: Suse 9 hangs after SMC2662W V3 hotplug)

"Andreas Schroff" <[email protected]>
Newsgroups gmane.linux.drivers.at76c503a.user
Message-ID <000a01c3cec2$c312eac0$8d7ba8c0@Cybercom>
Hello,
the related content of the log (withh debug information) is:


Dec 30 10:52:18 linux kernel: hub.c: new USB device 00:1f.2-2, assigned
address 3
Dec 30 10:52:18 linux kernel: usb.c: USB device 3 (vend/prod 0xd5c/0xa002)
is not claimed by any active driver.
Dec 30 10:52:22 linux kernel: usbdfu.c: USB Device Firmware Upgrade (DFU)
handler v0.12beta2 loading
Dec 30 10:52:22 linux kernel: at76c503.c: Generic Atmel at76c503/at76c505
routines v0.12beta2
Dec 30 10:52:22 linux kernel: at76c503-fw_skel.c: Atmel at76c503
(RFMD/Accton) Wireless LAN Driver v0.12beta2 loading
Dec 30 10:52:22 linux kernel: usb.c: registered new driver at76c503-rfmd-acc
Dec 30 10:52:22 linux kernel: at76c503-fw_skel.c: using compiled-in firmware
Dec 30 10:52:22 linux kernel: at76c503.c: wlan%%d: state 9 -> 9
(INTFW_DOWNLOAD)
Dec 30 10:52:22 linux insmod: Using
/lib/modules/2.4.21-99-default/kernel/drivers/usb/usbdfu.o
Dec 30 10:52:22 linux insmod: Symbol version prefix ''
Dec 30 10:52:22 linux insmod: Using
/lib/modules/2.4.21-99-default/kernel/drivers/usb/at76c503.o
Dec 30 10:52:22 linux insmod: Using
/lib/modules/2.4.21-99-default/kernel/drivers/usb/at76c503-rfmd-acc.o
Dec 30 10:52:22 linux kernel: usbdfu.c: dfu_download_block failed with -32
Dec 30 10:52:22 linux kernel: at76c503.c: downloading internal fw failed
with -32
Dec 30 10:52:22 linux kernel: usbdevfs: USBDEVFS_CONTROL failed dev 3 rqt
128 rq 6 len 18 ret -32
Dec 30 10:52:22 linux /etc/hotplug/usb.agent[2580]: cannot get config
descriptor: Broken pipe
Dec 30 10:52:23 linux /etc/hotplug/usb.agent[2580]: writing usb-1-3 to
/var/run/hotplug/net


Maybe this helps. Any ideas or hints?

Thank you

Andreas


----- Original Message ----- 
From: "Andreas Schroff" <[email protected]>
To: <[email protected]>
Sent: Monday, December 29, 2003 5:01 PM
Subject: Now no access point found (Re: [at76c503a-user] Suse 9 hangs after
SMC2662W V3 hotplug)


> Hello,
> in the mean time, I followed a hint in a similar posting. I did:
>
> rmmod usb-uhci
> insmod uhci
>
> Now the systems hangs not anymore and delivers output for the iwconfig
> command. After setting the configuration I receive:
>
> IEEE 802.11-DS  ESSID:"default"
> Mode:Managed  Channel:6  Access Point: 00:00:00:00:00:00
> Bit Rate:11Mb/s
> RTS thr:off   Fragment thr:off
> Encryption key:XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XX   Security mode:open
> Power Management:off
> Link Quality:0  Signal level:0  Noise level:0
> Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
> Tx excessive retries:0  Invalid misc:0   Missed beacon:0
>
>
>
> Using these options I use in windows xp, I cannot find my access point. If
I
> restart my machine with windows, I also need to unplug my SMC2662 device,
> before it works again.
>
>
>
> Is this related to firmware version somehow? The log tells me, that it
uses
> the compiled-in firmware. Firmware version ist displayed as 8.101.5 #84.
>
>
>
> Thank you
>
>
>
> Andreas
>
>
>
> > Hello,
> >
> > I use Suse 9 (Kernel 2.4.21) and have installed the at76c503a. After I
> plug
> > my SMC2662 V3 adapter in, my systems hangs. After a reboot I can find
the
> > following log:
> >
> > Dec 28 22:19:11 linux kernel: at76c503.c: Generic Atmel
at76c503/at76c505
> > routines v0.12beta2
> > Dec 28 22:19:11 linux kernel: at76c503-fw_skel.c: Atmel at76c503
> > (RFMD/Accton) Wireless LAN Driver v0.12beta2 loading
> > Dec 28 22:19:11 linux kernel: usb.c: registered new driver
> at76c503-rfmd-acc
> > Dec 28 22:20:13 linux kernel: at76c503-fw_skel.c: using compiled-in
> firmware
> > Dec 28 22:20:13 linux kernel: at76c503.c: getting firmware failed with
0,
> or
> > version is 0
> > Dec 28 22:20:13 linux kernel: at76c503.c: this probably means that the
> ext.
> > fw was not loaded correctly
> >
> >
> >
> > I read some postings about driver problems with usb code in some kernel
> > versions. As a Linux-Wlan-newbie, the reason for my problem should be
much
> > simpler....
> >
> >
> >
> > Thank you
> >
> >
> > Andreas
> >
> > _______________________________________________
> > at76c503a-user mailing list
> > [email protected]
> > http://lists.berlios.de/mailman/listinfo/at76c503a-user
>
> _______________________________________________
> at76c503a-user mailing list
> [email protected]
> http://lists.berlios.de/mailman/listinfo/at76c503a-user
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.