Driver not working in an ibook g4 using 2.6

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hi all list,

	I am trying to set up a BENQ AWL400 in my ibook g4. I'm using Linux 2.6 with 
benh patchset (other kernels/pachtsets don't work fine). When i plug the 
card, metalog tells the following:

Jan  2 17:30:56 [kernel] hub 4-0:1.0: new USB device on port 1, assigned 
address 4
Jan  2 17:30:56 [kernel] /usr/src/at76c503a/usbdfu.c: USB Device Firmware 
Upgrade (DFU) handler v0.12beta1 loading
Jan  2 17:30:56 [kernel] /usr/src/at76c503a/at76c503.c: Generic Atmel 
at76c503/at76c505 routines v0.12beta1
Jan  2 17:30:59 [kernel] /usr/src/at76c503a/at76c503.c: got unexp. config desc 
0902002001010080FA0904000002FF00FF000705850240000007050202400000
Jan  2 17:30:59 [kernel] /usr/src/at76c503a/at76c503.c: $Id: at76c503.c,v 
1.34.2.8 2003/12/25 22:19:43 jal2 Exp $ compiled Jan  1 2004 22:13:14
Jan  2 17:30:59 [kernel] /usr/src/at76c503a/at76c503.c: device's MAC 
00:03:9d:4b:71:a7, regulatory domain ETSI (Europe - (Spain+France) (id 48)


 Anyway, i can change essid, channel, nick... iwconfig parameters; but when i 
try to set an static ip i get this error (using dhcp to adquire one fails 
too):

americana root # ifconfig wlan0 192.168.232.50
SIOCSIFFLAGS: Bad address

In addition, metalog says:

Jan  2 17:32:44 [kernel] /usr/src/at76c503a/at76c503.c: submit_rx_urb: 
dev->read_urb is NULL

 I can see the iface with the ip:

americana root # ifconfig wlan0
wlan0     Link encap:Ethernet  HWaddr 00:03:9D:4B:71:A7
          inet addr:192.168.232.50  Bcast:192.168.232.255  Mask:255.255.255.0
          BROADCAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)


	But if i try to bring it up:

americana root # ifconfig wlan0 up
SIOCSIFFLAGS: Bad address

 And metalog says the same:

Jan  2 17:35:25 [kernel] /usr/src/at76c503a/at76c503.c: submit_rx_urb: 
dev->read_urb is NULL

  I don't know if is a 2.6 compatibility problem or it cames from the big 
endian architecture. I'll try using a 2.4 series kernel ASAP and i'll keep 
you informed.

Usefull data:

americana root # uname -a
Linux americana 2.6.0-benh2 #1 Wed Dec 31 15:52:40 CET 2003 ppc 7455, altivec 
supported PowerBook6,3 GNU/Linux

	(ppc-development-sources-2.6.0-r2 in Gentoo)

americana root # gcc --version
gcc (GCC) 3.2.3 20030422 (Gentoo Linux 1.4 3.2.3-r3, propolice)
Copyright (C) 2002 Free Software Foundation, Inc.
This is free software; see the source for copying conditions.  There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

Driver version: CVS Head

- -- 
Greetings,
/* Alberto García Hierro (Skyhusker) */
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.3 (GNU/Linux)

iD8DBQE/9a1t4O6JklHkL2cRAqO5AJ4nP1EfSXlkZjbCyrbiFWcg2b/KVACeN4m0
OFAwrLLKpr/jbksi3GXhx20=
=YB7l
-----END PGP SIGNATURE-----