at76c593a and WUSB11 2.6 problem

Hello, trying to use my WUSB11 2.6 on my laptop with my SMC wireless router. 
I think what's basically happening is it can't find the access point.  It 
appears to work, once it was even sending packets according to ifconfig but 
I still couldnt ping the router or any other machines.

dmesg with extra debug info after iwconfig/ifconfig:
hub 1-0:1.0: new USB device on port 1, assigned address 6
/root/at76c503a/at76c503a/at76c503-fw_skel.c: using compiled-in firmware
/root/at76c503a/at76c503a/at76c503.c: wlan%d: state 9 -> 9 (INTFW_DOWNLOAD)
/root/at76c503a/at76c503a/at76c503.c: wlan%d: state 9 -> 10 (EXTFW_DOWNLOAD)
/root/at76c503a/at76c503a/at76c503.c: wlan%d: state 10 -> 0 (INIT)
/root/at76c503a/at76c503a/at76c503.c: at76c503_alloc_urbs: NumEndpoints 2
/root/at76c503a/at76c503a/at76c503.c: at76c503_alloc_urbs: 0. endpoint: addr 
x85 attr x2
/root/at76c503a/at76c503a/at76c503.c: at76c503_alloc_urbs: 1. endpoint: addr 
x2 attr x2
/root/at76c503a/at76c503a/at76c503.c: $Id: at76c503.c,v 1.38 2003/12/27 
00:03:35 jal2 Exp $ compiled Dec 29 2003 05:03:51
/root/at76c503a/at76c503a/at76c503.c: firmware version 1.101.4 #84 (fcs_len 
4)
/root/at76c503a/at76c503a/at76c503.c: device's MAC 00:06:25:0e:8f:ae, 
regulatory domain FCC (U.S) (id 16)
/root/at76c503a/at76c503a/at76c503.c: registered wlan0
/root/at76c503a/at76c503a/at76c503.c: wlan0: state 0 -> 1 (SCANNING)
/root/at76c503a/at76c503a/at76c503.c: wlan0: rx frame: rate 0 rssi 26 noise 
0 link 0 
500070020006250E8FAE0004E249853A0004E249853AC0C3998C20F204000000640001000003534D43010482848B9603
/root/at76c503a/at76c503a/at76c503.c: wlan0: rx frame: rate 0 rssi 26 noise 
0 link 0 
80000000FFFFFFFFFFFF0004E249853A0004E249853AD0C338B221F204000000640001000003534D43010482848B9603
/root/at76c503a/at76c503a/at76c503.c: wlan0 BSS table (curr=00000000, 
new=00000000):
/root/at76c503a/at76c503a/at76c503.c: 0xcb163a40: bssid 00:04:e2:49:85:3a 
channel 6 ssid SMC (534D43) capa x0001 rates 82 84 8B 96 rssi 26 link 0 
noise 0
/root/at76c503a/at76c503a/at76c503.c: wlan0 BSS table (curr=00000000, 
new=00000000):
/root/at76c503a/at76c503a/at76c503.c: 0xcb163a40: bssid 00:04:e2:49:85:3a 
channel 6 ssid SMC (534D43) capa x0001 rates 82 84 8B 96 rssi 26 link 0 
noise 0
/root/at76c503a/at76c503a/at76c503.c: wlan0: state 1 -> 6 (JOINING)
/root/at76c503a/at76c503a/at76c503.c: wlan0 find_matching_bss: returned 
00000000
/root/at76c503a/at76c503a/at76c503.c: wlan0: state 6 -> 8 (STARTIBSS)
/root/at76c503a/at76c503a/at76c503.c: wlan0: rx frame: rate 0 rssi 26 noise 
0 link 0 
80000000FFFFFFFFFFFF0004E249853A0004E249853A20C43B8229F204000000640001000003534D43010482848B9603D43010482848B9603
/root/at76c503a/at76c503a/at76c503.c: using BSSID 02:00:26:4e:12:00
/root/at76c503a/at76c503a/at76c503.c: wlan0: rx frame: rate 0 rssi 26 noise 
0 link 0 
80000000FFFFFFFFFFFF0004E249853A0004E249853A30C43C122BF204000000640001000003534D43010482848B9603
/root/at76c503a/at76c503a/at76c503.c: wlan0: rx frame: rate 0 rssi 26 noise 
0 link 0 
80000000FFFFFFFFFFFF0004E249853A0004E249853A40C435A22CF204000000640001000003534D43010482848B9603
<repeats similar lines to the last 2 until device is powered down>

# iwconfig wlan0
wlan0     IEEE 802.11-DS  ESSID:"okuwlan"  Nickname:"okuwlan"
          Mode:Ad-Hoc  Channel:6  Cell: 02:00:26:4E:12:00
          Bit Rate:11Mb/s
          RTS thr=1536 B   Fragment thr=1536 B
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:87  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

# ifconfig wlan0 192.168.2.103
wlan0     Link encap:Ethernet  HWaddr 00:06:25:0E:8F:AE
          inet addr:192.168.2.103  Bcast:192.168.2.255  Mask:255.255.255.0
          UP BROADCAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)


Any help/ideas appreciated. I am running gentoo linux with a 2.6 kernel. I 
made sure that the router is working and set correctly (I believe... is it 
ok to leave Base speed at auto? (1/2 mbs) and Speed at auto (max is 11mbs)?)

Thanks.
-J

_________________________________________________________________
Check your PC for viruses with the FREE McAfee online computer scan.  
http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963