Fedora core 3+atmel+Linksys WUSB11 v2.6+opmode 185

This is a multi-part message in MIME format.

------=_NextPart_000_0010_01C4FC82.2D7755C0
Content-Type: text/plain;
	charset="us-ascii"
Content-Transfer-Encoding: 7bit

Aye All,

	I am having problems getting my Linksys WUSB11 v2.6 working under
Fedora Core 3, and was hoping that someone will be able to help me with this
problem.

	This is the error message I get from trying the drivers, snapshot
atmelwlandriver-ss-20041222.tar.gz, from
http://atmelwlandriver.sourceforge.net and the last CVS from
http://at76c503a.berlios.de/ 

/root/temp/temp2/at76c503a/at76c503.c: unexpected opmode 185

>From dmesg.  The following is the full display of the dmesg for the usb
decive.


usb 2-1: new full speed USB device using address 2
/root/temp/temp2/at76c503a/at76_usbdfu.c: USB Device Firmware Upgrade (DFU)
handler v0.12beta22-static loading
/root/temp/temp2/at76c503a/at76c503.c: Generic Atmel at76c503/at76c505
routines v0.12beta22-static/root/temp/temp2/at76c503a/at76c503-fw_skel.c:
Atmel at76c503 (RFMD) Wireless LAN Driver v0.12beta22-static loading
/root/temp/temp2/at76c503a/at76c503-fw_skel.c: using compiled-in firmware
usbcore: registered new driver at76c503-rfmd
usbcore: registered new driver usbvnetr
usb 2-1: reset full speed USB device using address 2
usb 2-1: device firmware changed
usb 2-1: USB disconnect, address 2
/root/temp/temp2/at76c503a/at76c503-fw_skel.c: wlan%d disconnecting
/root/temp/temp2/at76c503a/at76c503-fw_skel.c: at76c503-rfmd disconnected
usb 2-1: new full speed USB device using address 3
/root/temp/temp2/at76c503a/at76c503-fw_skel.c: using compiled-in firmware
/root/temp/temp2/at76c503a/at76c503.c: unexpected opmode 185

I get the following errors during the make usb:  

/root/temp/temp2/atmelwlandriver/objs/usbvnetr/debug/reset_device.c:24:17:
hub.h: No such file or directory
/root/temp/temp2/atmelwlandriver/objs/usbvnetr/debug/reset_device.c:25:17:
hcd.h: No such file or directory
make[3]: ***
[/root/temp/temp2/atmelwlandriver/objs/usbvnetr/debug/reset_device.o] Error
1
make[2]: *** [_module_/root/temp/temp2/atmelwlandriver/objs/usbvnetr/debug]
Error 2
make[2]: Leaving directory `/lib/modules/2.6.9-1.667/build'
make[1]: *** [all] Error 2
make[1]: Leaving directory
`/root/temp/temp2/atmelwlandriver/objs/usbvnetr/debug'
make: *** [usbvnetr] Error 2

I tried commenting out the #include hub.h and hcd.h and was able to finish
the make usb and then do a make install.  I am not sure if that was a good
idea or not.  In, either case here is some information about Fedora that you
might not be aware of:

In order to eliminate the redundancy inherent in providing a separate
package for the kernel source code when that source code already exists in
the kernel's .src.rpm file, Fedora Core 3 no longer includes the
kernel-source package. Users that require access to the kernel sources can
find them in the kernel .src.rpm file. To create an exploded source tree
from this file, perform the following steps (note that <version> refers to
the version specification for your currently-running kernel):  

From,
http://download.fedora.redhat.com/pub/fedora/linux/core/3/i386/os/RELEASE-NO
TES-en.html

Could this be part of the problem?   



I get the same unexpected opmode 185 with the http://at76c503a.berlios.de/
drivers.  I send the following information to their e-mail group; subject:
incompatible pointer type+Fedora Core 3  


make

 CC [M]  /root/temp/temp/at76c503a/at76c503.o
/root/temp/temp/at76c503a/at76c503.c: In function `ieee80211_to_eth':
/root/temp/temp/at76c503a/at76c503.c:3922: warning: assignment from
incompatible pointer type
  CC [M]  /root/temp/temp/at76c503a/at76_usbdfu.o
  Building modules, stage 2.
  MODPOST
  CC      /root/temp/temp/at76c503a/at76_usbdfu.mod.o

But, I still get a at76c503.o file and no errors at the end of make.  Make
install runs fine too.  


plug-in WUSB11 v2.6
dmesg displays the following

usb 2-1: new full speed USB device using address 2
/root/temp/temp/at76c503a/at76_usbdfu.c: USB Device Firmware Upgrade (DFU)
handler v0.12beta22-static loading
/root/temp/temp/at76c503a/at76c503.c: Generic Atmel at76c503/at76c505
routines v0.12beta22-static
/root/temp/temp/at76c503a/at76c503-fw_skel.c: Atmel at76c503 (RFMD) Wireless
LAN Driver v0.12beta22-static loading
/root/temp/temp/at76c503a/at76c503-fw_skel.c: using compiled-in firmware
usbcore: registered new driver at76c503-rfmd usb 2-1: reset full speed USB
device using address 2 usb 2-1: device firmware changed usb 2-1: USB
disconnect, address 2
/root/temp/temp/at76c503a/at76c503-fw_skel.c: wlan%d disconnecting
/root/temp/temp/at76c503a/at76c503-fw_skel.c: at76c503-rfmd disconnected usb
2-1: new full speed USB device using address 3
/root/temp/temp/at76c503a/at76c503-fw_skel.c: using compiled-in firmware
/root/temp/temp/at76c503a/at76c503.c: unexpected opmode 185

from
less /var/log/messages

Jan  2 22:45:18 atlantis kernel: usb 2-1: new full speed USB device using
address 2 Jan  2 22:45:19 atlantis kernel:
/root/temp/temp/at76c503a/at76_usbdfu.c:
USB Device Firmware Upgrade (DFU) handler v0.12beta22-static loading Jan  2
22:45:19 atlantis kernel: /root/temp/temp/at76c503a/at76c503.c:
Generic Atmel at76c503/at76c505 routines v0.12beta22-static Jan  2 22:45:19
atlantis kernel:
/root/temp/temp/at76c503a/at76c503-fw_skel.c: Atmel at76c503 (RFMD) Wireless
LAN Driver v0.12beta22-static loading Jan  2 22:45:20 atlantis kernel:
usbcore: registered new driver at76c503-rfmd Jan  2 22:45:21 atlantis
kernel: usb 2-1: reset full speed USB device using address 2 Jan  2 22:45:22
atlantis kernel: usb 2-1: device firmware changed Jan  2 22:45:22 atlantis
kernel: usb 2-1: USB disconnect, address 2 Jan  2 22:45:22 atlantis kernel:
/root/temp/temp/at76c503a/at76c503-fw_skel.c: wlan%%d disconnecting Jan  2
22:45:22 atlantis kernel:
/root/temp/temp/at76c503a/at76c503-fw_skel.c: at76c503-rfmd disconnected Jan
2 22:45:22 atlantis kernel: usb 2-1: new full speed USB device using address
3 Jan  2 22:45:22 atlantis kernel: /root/temp/temp/at76c503a/at76c503.c:
unexpected opmode 185


So does this mean I am having problems downloading the firmware on my KT133
chip set?  Should I try and spend money on a cheap USB hub??  Please let me
know.  Thanks Again!!


Thanks for taking the time out to read the full message!!!  If you have any
ideas please let me know, and I will try them.

Thanks,
Pruse  

------=_NextPart_000_0010_01C4FC82.2D7755C0
Content-Type: text/plain; charset="us-ascii"
MIME-Version: 1.0
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________
Atmel-wlan-usb mailing list
Atmel-wlan-usb-ikZNBd7uB5wQUIZIPwn63sWURRETrGNnG9Ur7JDdleE@public.gmane.org
https://iprserv.jura.uni-leipzig.de/mailman/listinfo/atmel-wlan-usb

------=_NextPart_000_0010_01C4FC82.2D7755C0--