Re: RedHat 7.3 & vpn client 3.5.2 on T23

Donald Becker wrote:
> 
> On Fri, 21 Jun 2002, Michael Barnes wrote:
> > Donald Becker wrote:
> > > On Fri, 21 Jun 2002, Michael Barnes wrote:
> > > > I just got an IBM T23, installed RedHat 7.3, and did up2date.
> > > > Jun 21 13:56:23 dhcp-2545-22 kernel: eepro100: wait_for_cmd_done timeout!
> > > ..
> > > > Jun 21 13:58:27 dhcp-2545-22 kernel: NETDEV WATCHDOG: eth0: transmit timed
> > > > out
> > > > Jun 21 13:58:27 dhcp-2545-22 kernel: eth0: Transmit timed out: status 0050
> > > > 0c80 at 30928/30988 command 200c0000.
> ...
> > > > I saw in the archive a message that suggests to disable sleep mode, but I
> > > > can't find instructions on how to do that, if that would help.
> > > Run
> > >   eepro100-diag -ee
> 
> > I am getting the same errors even after using that command. What else could
> > be the cause?
> 
> What did the command report?

This is the console log from when I checked the interface, disabled sleep
mode, and re-checked the interface 

[root@localhost eepro100-diag]# ./eepro100-diag -ee -f
eepro100-diag.c:v2.08 4/17/2002 Donald Becker ([email protected])
 http://www.scyld.com/diag/index.html
Index #1: Found a Intel Pro/100 VE (type 1031) adapter at 0x6400.
EEPROM contents, size 64x16:
    00: d000 bf59 b1ec 1a03 0000 0201 4701 0000
  0x08: 0000 0000 49a2 0209 1014 007f 0000 0000
      ...
  0x20: 0000 0000 0000 1031 0000 0000 0000 0000
      ...
  0x30: 002c 4000 4016 0000 0000 0000 0000 0000
  0x38: 0000 0000 0000 4030 0000 0000 0000 e98f
 The EEPROM checksum is correct.
Intel EtherExpress Pro 10/100 EEPROM contents:
  Station address 00:D0:59:BF:EC:B1.
  Board assembly 000000-000, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
   Sleep mode is enabled.  This is not recommended.
   Under high load the card may not respond to
   PCI requests, and thus cause a master abort.
   To clear sleep mode use the '-G 0 -w -w -f' options.
[root@localhost eepro100-diag]# ./eepro100-diag -G 0 -w -w -f
eepro100-diag.c:v2.08 4/17/2002 Donald Becker ([email protected])
 http://www.scyld.com/diag/index.html
Index #1: Found a Intel Pro/100 VE (type 1031) adapter at 0x6400.
Writing 49a0 to configuration word 10.
 Use '-a' or '-aa' to show device registers,
     '-e' to show EEPROM contents, -ee for parsed contents,
  or '-m' or '-mm' to show MII management registers.
[root@localhost eepro100-diag]#
[root@localhost eepro100-diag]#
[root@localhost eepro100-diag]# ./eepro100-diag -ee
eepro100-diag.c:v2.08 4/17/2002 Donald Becker ([email protected])
 http://www.scyld.com/diag/index.html
Index #1: Found a Intel Pro/100 VE (type 1031) adapter at 0x6400.
A potential i82557 chip has been found, but it appears to be active.
Either shutdown the network, or use the '-f' flag.
[root@localhost eepro100-diag]# ./eepro100-diag -ee -f
eepro100-diag.c:v2.08 4/17/2002 Donald Becker ([email protected])
 http://www.scyld.com/diag/index.html
Index #1: Found a Intel Pro/100 VE (type 1031) adapter at 0x6400.
EEPROM contents, size 64x16:
    00: d000 bf59 b1ec 1a03 0000 0201 4701 0000
  0x08: 0000 0000 49a0 0209 1014 007f 0000 0000
      ...
  0x20: 0000 0000 0000 1031 0000 0000 0000 0000
      ...
  0x30: 002c 4000 4016 0000 0000 0000 0000 0000
  0x38: 0000 0000 0000 4030 0000 0000 0000 e991
 The EEPROM checksum is correct.
Intel EtherExpress Pro 10/100 EEPROM contents:
  Station address 00:D0:59:BF:EC:B1.
  Board assembly 000000-000, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.


> What driver version are you using?

It looks like it is v1.09 Revision 1.36

> --
> Donald Becker                           [email protected]
> Scyld Computing Corporation             http://www.scyld.com
> 410 Severn Ave. Suite 210               Second Generation Beowulf Clusters
> Annapolis MD 21403                      410-990-9993

-- 
Michael Barnes
Core IP Eng - Routing
408-525-2785