Fw: 2.4.20 eepro100 oops
Nicholas Henke <[email protected]> Tue, 1 Apr 2003 16:22:33 -0500
| Newsgroups | gmane.linux.drivers.eepro100.devel |
|---|---|
| Message-ID | <[email protected]> |
Begin forwarded message: Date: Tue, 1 Apr 2003 13:28:28 -0500 From: Nicholas Henke <[email protected]> To: [email protected] Cc: [email protected],[email protected],[email protected] Subject: 2.4.20 eepro100 oops Hey all -- I was not sure where to send this, so my applogies for the mass send. I am running a stock 2.4.20, and I get the following oops when I try to insmod eepr100. I do not get the same thing when using the e100 driver. Both are compiled as modules, and running on an updated RH 7.2. The following is the infomation from the e100 drivers about what chipset I have: Intel(R) PRO/100 Network Driver - version 2.1.24-k1 Copyright (c) 2002 Intel Corporation e100: selftest OK. e100: eth0: Intel(R) PRO/100+ Management Adapter Mem:0xf4200000 IRQ:18 Speed:0 Mbps Dx:N/A Hardware receive checksums enabled cpu cycle saver enabled e100: selftest OK. e100: eth1: Intel(R) 82559 Fast Ethernet LAN on Motherboard Mem:0xf4203000 IRQ:21 Speed:0 Mbps Dx:N/A Hardware receive checksums enabled cpu cycle saver enabled The ooutput from ksymoops is attached as oops1_out. Please let me know if there is any more information I can supply. Nic P.S Please CC me on any replies. :::::::::oops1::::::::::::: Linux version 2.4.20-cm2custom ([email protected]) (gcc version 2.96 20000731 (Red Hat Linux 7.2 2.96-112.7.2)) #1 SMP Tue Apr 1 21:47:58 EST 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) BIOS-e820: 000000003fff0000 - 000000003ffffc00 (ACPI data) BIOS-e820: 000000003ffffc00 - 0000000040000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f6ab0 hm, page 000f6000 reserved twice. hm, page 000f7000 reserved twice. hm, page 0009f000 reserved twice. hm, page 000a0000 reserved twice. On node 0 totalpages: 262128 zone(0): 4096 pages. zone(1): 225280 pages. zone(2): 32752 pages. Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: INTEL Product ID: Cypress APIC at: 0xFEE00000 Processor #1 Pentium(tm) Pro APIC version 17 Processor #0 Pentium(tm) Pro APIC version 17 I/O APIC #2 Version 17 at 0xFEC00000. Processors: 2 Kernel command line: ro root=/dev/hda2 Initializing CPU#0 Detected 547.627 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 1091.17 BogoMIPS Memory: 1032960k/1048512k available (1388k kernel code, 15164k reserved, 490k data, 140k init, 131008k highmem) Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode cache hash table entries: 65536 (order: 7, 524288 bytes) Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K CPU serial number disabled. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch ([email protected]) mtrr: detected mtrr type: Intel CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU0: Intel Pentium III (Katmai) stepping 03 per-CPU timeslice cutoff: 1462.36 usecs. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Booting processor 1/0 eip 2000 Initializing CPU#1 masked ExtINT on CPU#1 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 1094.45 BogoMIPS CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K CPU serial number disabled. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU1: Intel Pentium III (Katmai) stepping 03 Total of 2 processors activated (2185.62 BogoMIPS). ENABLING IO-APIC IRQs Setting 2 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-5, 2-9, 2-10, 2-11, 2-16, 2-17, 2-20, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 17. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 .... register #01: 00170011 ....... : max redirection entries: 0017 ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 000 00 1 0 0 0 0 0 0 00 06 003 03 0 0 0 0 0 1 1 51 07 003 03 0 0 0 0 0 1 1 59 08 003 03 0 0 0 0 0 1 1 61 09 000 00 1 0 0 0 0 0 0 00 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 003 03 0 0 0 0 0 1 1 69 0d 003 03 0 0 0 0 0 1 1 71 0e 003 03 0 0 0 0 0 1 1 79 0f 003 03 0 0 0 0 0 1 1 81 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 003 03 1 1 0 1 0 1 1 89 13 003 03 1 1 0 1 0 1 1 91 14 000 00 1 0 0 0 0 0 0 00 15 003 03 1 1 0 1 0 1 1 99 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ18 -> 0:18 IRQ19 -> 0:19 IRQ21 -> 0:21 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 547.6131 MHz. ..... host bus clock speed is 99.5657 MHz. cpu: 0, clocks: 995657, slice: 331885 CPU0<T0:995648,T1:663760,D:3,S:331885,C:995657> cpu: 1, clocks: 995657, slice: 331885 CPU1<T0:995648,T1:331872,D:6,S:331885,C:995657> checking TSC synchronization across CPUs: passed. Waiting on wait_init_idle (map = 0x2) All processors have done init_idle PCI: PCI BIOS revision 2.10 entry at 0xfdab0, last bus=2 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Discovered primary peer bus ff [IRQ] PCI: Using IRQ router PIIX [8086/7110] at 00:12.0 PCI->APIC IRQ transform: (B0,I11,P0) -> 18 PCI->APIC IRQ transform: (B0,I12,P0) -> 19 PCI->APIC IRQ transform: (B0,I12,P0) -> 19 PCI->APIC IRQ transform: (B0,I14,P0) -> 21 PCI->APIC IRQ transform: (B0,I18,P3) -> 21 PCI: Cannot allocate resource region 4 of device 00:12.1 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS not found. Starting kswapd allocated 32 pages and 32 bhs reserved for the highmem bounces VFS: Diskquotas version dquot_6.4.0 initialized pty: 512 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10e Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller on PCI bus 00 dev 91 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:DMA hda: WDC WD200BB-00AUA1, ATA DISK drive hdb: WDC WD200BB-00AUA1, ATA DISK drive hdd: ATAPI 52X CDROM, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 blk: queue c035f0e4, I/O limit 4095Mb (mask 0xffffffff) hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=2434/255/63, UDMA(33) blk: queue c035f230, I/O limit 4095Mb (mask 0xffffffff) hdb: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=2434/255/63, UDMA(33) ide-floppy driver 0.99.newide Partition check: hda: hda1 hda2 hda3 hda4 < hda5 > hdb: hdb1 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize ide-floppy driver 0.99.newide md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 251k freed VFS: Mounted root (ext2 filesystem). SCSI subsystem driver Revision: 1.00 scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8 <Adaptec aic7896/97 Ultra2 SCSI adapter> aic7896/97: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8 <Adaptec aic7896/97 Ultra2 SCSI adapter> aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/253 SCBs blk: queue c1cf6618, I/O limit 4095Mb (mask 0xffffffff) Journalled Block Device driver loaded EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 140k freed Adding Swap: 2096440k swap-space (priority -1) usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.275 $ time 21:25:42 Apr 1 2003 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: USB UHCI at I/O 0x1060, IRQ 21 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,65), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal EXT3-fs: mounted filesystem with ordered data mode. parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: irq 7 detected ip_conntrack version 2.1 (8191 buckets, 65528 max) - 292 bytes per conntrack eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others eth0: Intel Corp. 82557/8/9 [Ethernet Pro 100], 00:90:27:61:70:E4, IRQ 18. Board assembly 721383-006, Physical connectors present: RJ45 Primary interface chip i82555 PHY #1. Unable to handle kernel NULL pointer dereference at virtual address 00000010 printing eip: f8a39b33 *pde = 2589b001 *pte = 00000000 Oops: 0002 CPU: 0 EIP: 0010:[<f8a39b33>] Not tainted EFLAGS: 00010206 eax: 08200000 ebx: f8a3d3c4 ecx: 00000000 edx: 00200000 esi: 00000280 edi: 00003e80 ebp: e89a5000 esp: f71b1c5c ds: 0018 es: 0018 ss: 0018 Process modprobe (pid: 571, stackpage=f71b1000) Stack: f8a3d3c4 f71b1c94 f8a39649 f8a40000 00000001 00000000 0000baba 00000040 01800000 00001080 e4fe7000 00000000 24fe7000 00000000 f8a3d42d f8a3d433 f8a3d438 f8a3d43d 61279000 0203e470 02010000 00004701 83067213 000c40a2 Call Trace: [<f8a3d3c4>] [<f8a39649>] [<f8a3d42d>] [<f8a3d433>] [<f8a3d438>] [<f8a3d43d>] [<c012c74a>] [<c012c7a7>] [<c0124d00>] [<c0137b61>] [<c012c1d2>] [<c012c1fe>] [<c01152d0>] [<c0115341>] [<c01152d0>] [<c01180ea>] [<c01181d0>] [<f8a391e0>] [<f8a3e690>] [<f8a3e9a0>] [<c01d822c>] [<f8a3e690>] [<f8a3e9a0>] [<c01d8292>] [<f8a3e9a0>] [<f8a3c440>] [<f8a3c31c>] [<f8a3e9a0>] [<c011d615>] [<f8a3d67c>] [<f8a39060>] [<c0108d03>] Code: 89 41 10 8d 76 00 8d bc 27 00 00 00 00 4e 8b 59 10 79 0f 53 :::::::oops1_out::::::::::::::::; ksymoops 2.4.1 on i686 2.4.20-cm2custom. Options used -v /boot/vmlinux (specified) -k /proc/ksyms (default) -l /proc/modules (default) -o /lib/modules/2.4.20-cm2custom/ (default) -m /boot/System.map-2.4.20-cm2custom (default) -a i686 Error (expand_objects): cannot stat(/lib/ext3.o) for ext3 Error (expand_objects): cannot stat(/lib/jbd.o) for jbd Error (expand_objects): cannot stat(/lib/aic7xxx.o) for aic7xxx Error (expand_objects): cannot stat(/lib/sd_mod.o) for sd_mod Error (expand_objects): cannot stat(/lib/scsi_mod.o) for scsi_mod Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/cdrom/driver.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/char/drm/drm.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/hotplug/vmlinux-obj.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/isdn/hisax/vmlinux-obj.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/isdn/vmlinux-obj.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/media/radio/radio.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/media/video/video.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/media/media.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/misc/misc.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/net/fc/fc.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/net/pcmcia/pcmcia_net.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/net/tokenring/tr.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/net/wan/wan.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/net/wireless/wireless_net.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/parport/driver.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/sound/sounddrivers.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/net/ipv4/netfilter/netfilter.o Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/net/ipv6/netfilter/netfilter.o Warning (compare_maps): mismatch on symbol usb_devfs_handle , usbcore says f89dca74, /lib/modules/2.4.20-cm2custom/kernel/drivers/usb/usbcore.o says f89dc4f4. Ignoring /lib/modules/2.4.20-cm2custom/kernel/drivers/usb/usbcore.o entry Warning (map_ksym_to_module): cannot match loaded module ext3 to a unique module object. Trace may not be reliable. Warning (map_ksym_to_module): cannot match loaded module jbd to a unique module object. Trace may not be reliable. Warning (map_ksym_to_module): cannot match loaded module aic7xxx to a unique module object. Trace may not be reliable. Warning (map_ksym_to_module): cannot match loaded module sd_mod to a unique module object. Trace may not be reliable. Warning (map_ksym_to_module): cannot match loaded module scsi_mod to a unique module object. Trace may not be reliable. cpu: 0, clocks: 995657, slice: 331885 cpu: 1, clocks: 995657, slice: 331885 Unable to handle kernel NULL pointer dereference at virtual address 00000010 f8a39b33 *pde = 2589b001 Oops: 0002 CPU: 0 EIP: 0010:[<f8a39b33>] Not tainted Using defaults from ksymoops -t elf32-i386 EFLAGS: 00010206 eax: 08200000 ebx: f8a3d3c4 ecx: 00000000 edx: 00200000 esi: 00000280 edi: 00003e80 ebp: e89a5000 esp: f71b1c5c ds: 0018 es: 0018 ss: 0018 Process modprobe (pid: 571, stackpage=f71b1000) Stack: f8a3d3c4 f71b1c94 f8a39649 f8a40000 00000001 00000000 0000baba 00000040 01800000 00001080 e4fe7000 00000000 24fe7000 00000000 f8a3d42d f8a3d433 f8a3d438 f8a3d43d 61279000 0203e470 02010000 00004701 83067213 000c40a2 Call Trace: [<f8a3d3c4>] [<f8a39649>] [<f8a3d42d>] [<f8a3d433>] [<f8a3d438>] [<f8a3d43d>] [<c012c74a>] [<c012c7a7>] [<c0124d00>] [<c0137b61>] [<c012c1d2>] [<c012c1fe>] [<c01152d0>] [<c0115341>] [<c01152d0>] [<c01180ea>] [<c01181d0>] [<f8a391e0>] [<f8a3e690>] [<f8a3e9a0>] [<c01d822c>] [<f8a3e690>] [<f8a3e9a0>] [<c01d8292>] [<f8a3e9a0>] [<f8a3c440>] [<f8a3c31c>] [<f8a3e9a0>] [<c011d615>] [<f8a3d67c>] [<f8a39060>] [<c0108d03>] Code: 89 41 10 8d 76 00 8d bc 27 00 00 00 00 4e 8b 59 10 79 0f 53 Error (Oops_bfd_perror): scan_arch for specified architecture Success >>EIP; f8a39b33 <[eepro100]mdio_read+23/60> <===== Trace; f8a3d3c4 <[eepro100].LC53+1a/1e> Trace; f8a39649 <[eepro100]speedo_found1+3d9/730> Trace; f8a3d42d <[eepro100].LC63+e/18> Trace; f8a3d433 <[eepro100].LC63+14/18> Trace; f8a3d438 <[eepro100].LC65+1/9> Trace; f8a3d43d <[eepro100].LC65+6/9> Trace; c012c74a <do_anonymous_page+14a/170> Trace; c012c7a7 <do_no_page+37/250> Trace; c0124d00 <update_process_times+20/a0> Trace; c0137b61 <__alloc_pages+41/170> Trace; c012c1d2 <do_wp_page+2e2/330> Trace; c012c1fe <do_wp_page+30e/330> Trace; c01152d0 <flush_tlb_all_ipi+0/60> Trace; c0115341 <flush_tlb_all+11/70> Trace; c01152d0 <flush_tlb_all_ipi+0/60> Trace; c01180ea <remap_area_pages+20a/220> Trace; c01181d0 <__ioremap+d0/f0> Trace; f8a391e0 <[eepro100]eepro100_init_one+180/210> Trace; f8a3e690 <[eepro100]eepro100_pci_tbl+0/2f4> Trace; f8a3e9a0 <[eepro100]eepro100_driver+0/3f> Trace; c01d822c <pci_announce_device+3c/60> Trace; f8a3e690 <[eepro100]eepro100_pci_tbl+0/2f4> Trace; f8a3e9a0 <[eepro100]eepro100_driver+0/3f> Trace; c01d8292 <pci_register_driver+42/60> Trace; f8a3e9a0 <[eepro100]eepro100_driver+0/3f> Trace; f8a3c440 <[eepro100].text.end+51/ed1> Trace; f8a3c31c <[eepro100]eepro100_init_module+1c/50> Trace; f8a3e9a0 <[eepro100]eepro100_driver+0/3f> Trace; c011d615 <sys_init_module+555/630> Trace; f8a3d67c <[eepro100].LC37+1c/60> Trace; f8a39060 <[eepro100]eepro100_init_one+0/210> Trace; c0108d03 <system_call+33/38> 24 warnings and 6 errors is -- Nicholas Henke Penguin Herder & Linux Cluster System Programmer Liniac Project - Univ. of Pennsylvania