| Newsgroups |
gmane.linux.drivers.eepro100.devel |
| Message-ID |
<[email protected]> |
(sorry if this is double posted; my webmail client went bonkers)
Hi,
I recently installed Red Hat 9 and compiled kernel 2.4.23 for my Sony
Vaio 505BX. It contains the Inte Pro/100 VE adapter.
Anyway, for both the 2.4.20 (original RH9 kernel) and the 2.4.23
kernels, the card can ping within the LAN but not outside the LAN.
I've already read a previous post where someone had similar troubles.
I know it isn't a router problem (but possibly _routing_ problem).
Anyway, eepro100-diag, mii-diag, and pci-config all show normal info.
Under Windows XP, I can do all normal net activities (ping, http,
etc). Under linux (either kernel) I can only pin inside the LAN. If
it's a routing problem, what's causing it? The second line (see
below) for route -n seems rather bogus -- if this is it, how does one
go about fixing it?
My own comments:
- I don't think it's a sleep mode problem
- It's not a problem at the router since the ethernet works under
Windows XP, but what do I know
- The card works fine transferring within the LAN under linux
# eepro100-diag -f -ee -m
eepro100-diag.c:v2.12 4/15/2003 Donald Becker ([email protected])
http://www.scyld.com/diag/index.html
Index #1: Found a Intel Pro/100 VE (type 1031) adapter at 0x4000.
EEPROM contents, size 64x16:
00: 0008 ac46 0152 1a03 0000 0201 4701 0000 __F_R________G__
0x08: 0000 0000 49b0 8147 104d 007f 0000 0000 _____IG_M_______
...
0x20: 0000 0000 0000 1031 0000 0000 0000 0000 ______1_________
...
0x30: 002c 0000 0000 0000 0000 0000 0000 0000 ,_______________
0x38: 0000 0000 0000 4030 0000 0000 0000 7dc5 ______0@_______}
The EEPROM checksum is correct.
Intel EtherExpress Pro 10/100 EEPROM contents:
Station address 08:00:46:AC:52:01.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Primary transceiver is MII PHY #1. MII PHY #1 transceiver registers:
3100 782d 02a8 0330 05e1 45e1 0001 0000
0000 0000 0000 0000 0000 0000 0000 0000
2a07 0000 0000 0c5b 0000 0000 1071 0000
0003 0000 0000 0000 0010 0000 0000 0000.
# mii-diag
Using the default interface 'eth0'.
Basic registers of MII PHY #1: 3100 782d 02a8 0330 05e1 45e1 0001
0000.
The autonegotiated capability is 01e0.
The autonegotiated media type is 100baseTx-FD.
Basic mode control register 0x3100: Auto-negotiation enabled.
You have link beat, and everything is working OK.
Your link partner advertised 45e1: Flow-control 100baseTx-FD
100baseTx 10baseT-FD 10baseT, w/ 802.3X flow control.
End of basic transceiver information.
# cat /proc/pci (partial listing)
Bus 2, device 8, function 0:
Ethernet controller: Intel Corp. 82801CAM (ICH3) PRO/100 VE (LOM)
Ethernet Controller (rev 66).
IRQ 10.
Master Capable. Latency=66. Min Gnt=8.Max Lat=56.
Non-prefetchable 32 bit memory at 0xe8202000 [0xe8202fff].
I/O at 0x4000 [0x403f].
# pci-config -B2 -#7 -a
pci-config.c:v2.03 4/15/2002 Donald Becker ([email protected])
http://www.scyld.com/diag/index.html
Device #7 at bus 2 device/function 8/0.
10318086 02900017 02000042 00004210 e8202000 00004001 00000000
00000000
00000000 00000000 00000000 8147104d 00000000 000000dc 00000000
3808010a
00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000
fe220001
3a004000 00000000 00000000 00000000 00000000 00000000 00000000
00000000
Base Address 0: Memory at e8202000.
Base Address 1: I/O at 00004000.
Address 0 memory at e8202000, decoded bits are 00000fff.
Address 1 is I/O at 00004000, decoded bits are 0000003e.
No BIOS extension (boot ROM).
Extended capabilities, first structure at offset 0xdc.
Extended PCI capability type 1 at 0xdc, next 0.
Power management entry ver. 2: Capabilities fe22, Ctrl 4000, Event
3a00.
Power state D0.
# dmesg (snippet)
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V.
Savochkin <[email protected]> and others
PCI: Found IRQ 10 for device 02:08.0
PCI: Sharing IRQ 10 with 02:07.1
divert: allocating divert_blk for eth0
eth0: Intel Corp. 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet
Controller, 08:00:46:AC:52:01, IRQ 10.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref
Use Iface
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0
0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0
0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0
0 lo
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0
0 eth0
Sincerely,
Han