Re: Fwd: Hs 2.0: PMF not negotiated by release 2
François Vergès <[email protected]>
| Newsgroups | gmane.linux.drivers.hostap |
|---|---|
| Message-ID | <CA+SJyJ8iO1ST2grdbObx_LJaq1NiV1ne7iHSMVXSrV9V8jLE-w@mail.gmail.com> |
Ok, thank you. Best Regards, François On Thu, Jan 23, 2020 at 5:43 PM Ben Greear <[email protected]> wrote: > > You do not need the non-commercial firmware unless you are building multi-station > emulator test rigs, so please just use the community version. > > Thanks, > Ben > > On 1/23/20 1:40 PM, François Vergès wrote: > > Hello Ben, > > > > Thank you for your answer. > > > > Looking for the ath10k-ct, I noticed that there are 2 versions > > available (community and non-commercial). Will I be able to setup H2.0 > > with the community version? > > > > Best Regards, > > François > > > > > > François Vergès, CWNE#180 > > Wireless Network Engineer & Owner > > SemFio Networks Inc. > > Tel: +1 514 475-5305 > > Email: [email protected] > > Website: www.semfionetworks.com > > > > > > > > Want to learn more about how Wi-Fi 6 works? - Listen here: > > https://www.cleartosend.net/ax > > > > > > On Mon, Jan 20, 2020 at 6:29 PM Ben Greear <[email protected]> wrote: > >> > >> Hello, > >> > >> Ath9k pcie cards should work, and we have had success with ath10k-ct > >> drivers/firmware before. > >> > >> Thanks, > >> Ben > >> > >> On 1/20/20 2:28 PM, François Vergès wrote: > >>> Thank you for your answer Jouni. > >>> > >>> Do you know any combination of driver/chipset I could use to make > >>> Hotspot 2.0 Rel 2 work? > >>> > >>> > >>> François Vergès, CWNE#180 > >>> Wireless Network Engineer & Owner > >>> SemFio Networks Inc. > >>> Tel: +1 514 475-5305 > >>> Email: [email protected] > >>> Website: www.semfionetworks.com > >>> > >>> > >>> > >>> Want to learn more about how Wi-Fi 6 works? - Listen here: > >>> https://www.cleartosend.net/ax > >>> > >>> > >>> On Mon, Jan 20, 2020 at 5:00 PM Jouni Malinen <[email protected]> wrote: > >>>> > >>>> On Mon, Jan 20, 2020 at 03:28:03PM -0500, François Vergès wrote: > >>>>> I have tried to add the "ieee802.11w=1" to the configurations but > >>>>> hostapd doesn't start when I do so. > >>>>> > >>>>> Here is what the logs is telling me: "nl80211: set_key failed; err=-22 > >>>>> Invalid argument)". > >>>> > >>>>> wpa_driver_nl80211_set_key: ifindex=4 (wlx000e8e9082a7) alg=4 > >>>>> addr=0x561270d06058 key_idx=4 set_tx=1 seq_len=0 key_len=16 > >>>>> nl80211: KEY_DATA - hexdump(len=16): [REMOVED] > >>>>> broadcast key > >>>>> nl80211: set_key failed; err=-22 Invalid argument) > >>>> > >>>> This alg=4 (WPA_ALG_IGTK), key_idx=4 is the key used by PMF for > >>>> protecting group addressed robust management frames. It looks like the > >>>> driver used here does not support BIP and as such, it cannot be used > >>>> with PMF. Consequently, it is not suitable for use with Hotspot 2.0 Rel > >>>> 2. > >>>> > >>>> -- > >>>> Jouni Malinen PGP id EFC895FA > >>> > >>> _______________________________________________ > >>> Hostap mailing list > >>> [email protected] > >>> http://lists.infradead.org/mailman/listinfo/hostap > >>> > >> > >> > >> -- > >> Ben Greear <[email protected]> > >> Candela Technologies Inc http://www.candelatech.com > >> > > > > > -- > Ben Greear <[email protected]> > Candela Technologies Inc http://www.candelatech.com > _______________________________________________ Hostap mailing list [email protected] http://lists.infradead.org/mailman/listinfo/hostap