PSC 2350 & hpoj trouble

Hello,

I have a serious trouble to make running hpoj with my PSC 2350 ...

I'm using a Debian in SID ... with a hand made kernel 2.6.13.1

I have connected the printer in USB ...

less /proc/bus/usb/devices :
T:  Bus=3D01 Lev=3D01 Prnt=3D01 Port=3D00 Cnt=3D01 Dev#=3D  4 Spd=3D12  MxC=
h=3D 0
D:  Ver=3D 2.00 Cls=3D00(>ifc ) Sub=3D00 Prot=3D00 MxPS=3D 8 #Cfgs=3D  1
P:  Vendor=3D03f0 ProdID=3D4911 Rev=3D 1.00
S:  Manufacturer=3DHP
S:  Product=3DPSC 2350 series
S:  SerialNumber=3DHU47TBR17TKJ
C:* #Ifs=3D 4 Cfg#=3D 1 Atr=3Dc0 MxPwr=3D  2mA
I:  If#=3D 0 Alt=3D 0 #EPs=3D 3 Cls=3Dff(vend.) Sub=3Dcc Prot=3D00 Driver=
=3D(none)
E:  Ad=3D01(O) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D81(I) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D82(I) Atr=3D03(Int.) MxPS=3D   8 Ivl=3D10ms
I:  If#=3D 1 Alt=3D 0 #EPs=3D 3 Cls=3D07(print) Sub=3D01 Prot=3D02 Driver=
=3Dusblp
E:  Ad=3D03(O) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D83(I) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D84(I) Atr=3D03(Int.) MxPS=3D   8 Ivl=3D10ms
I:  If#=3D 2 Alt=3D 0 #EPs=3D 3 Cls=3Dff(vend.) Sub=3Dff Prot=3Dff Driver=
=3D(none)
E:  Ad=3D05(O) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D85(I) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D86(I) Atr=3D03(Int.) MxPS=3D   8 Ivl=3D10ms
I:  If#=3D 2 Alt=3D 1 #EPs=3D 3 Cls=3Dff(vend.) Sub=3Dd4 Prot=3D00 Driver=
=3D(none)
E:  Ad=3D05(O) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D85(I) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D86(I) Atr=3D03(Int.) MxPS=3D   8 Ivl=3D10ms
I:  If#=3D 3 Alt=3D 0 #EPs=3D 2 Cls=3D08(stor.) Sub=3D06 Prot=3D50 Driver=
=3Dusb-storage
E:  Ad=3D07(O) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D87(I) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms

So it seems that the usblp and usb-storage are here ...

But :
ptal-init setup give me alway this answer ...

Probe for USB-connected devices ([y]/n)?

Probing "/dev/usb/lp0"...
    *** Found "PSC 2350 series" but failed to communicate with it!
    *** Elapsed time for this attempt was 0 second(s).
    *** Check syslog file for ptal-mlcd error messages.
    *** See hpoj documentation for troubleshooting information.

I haven't find any solution in the documentation ...
=46or your information I'm printing perfectly on my printer using CUPS with=
 this=20
configuration :
# Printer configuration file for CUPS v1.1.23
# Written by cupsd on dim 18 d=E9c 2005 03:22:43 CET
<DefaultPrinter HP_PSC2350>
Info Imprimante Jet d'encre couleur
Location Bureau Herv=E9
DeviceURI usb://5740?serial=3DHU47TBR17TKJ
State Idle
Accepting Yes
JobSheets none none
QuotaPeriod 0
PageLimit 0
KLimit 0
</Printer>

So what can I do to make hpoj running ?? I want to use xsane for scanning .=
=2E.=20
and I haven't found any solution ... thanks per advance ...

Regards,
=2D-=20
Herv=E9 Piedvache


-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files
for problems?  Stop!  Download the new AJAX search engine that makes
searching your log files as easy as surfing the  web.  DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_id=7637&alloc_id=16865&op=click