Re: ipw2200 issue

 
Dear Zhu Yi,

I did it and it was same.

There is no /sys and /sysfs directory and I made them, then I can run mount
-a.
After I mount the sysfs, the /sys is empty yet and /sysfs has subdirectory
and files.

I enable kernel debug, and new message below:
*******************************************************
modprobe ipw2200 Using /lib/modules/2.6.15-sigma/kobject ieee80211_crypt:
registering. parent: <NULL>, set: module

kernel/net/ieee8kobject_hotplug

0211/ieee80211_cfill_kobj_path: path = '/module/ieee80211_crypt'

rypt.ko kobject_hotplug: /sbin/hotplug module seq=659 HOME=/
PATH=/sbin:/bin:/usr/sbin:/usr/bin ACTION=add
DEVPATH=/module/ieee80211_crypt SUBSYSTEM=module

kobject_hotplug - call_usermodehelper returned -1

ieee80211_crypt: registered algorithm 'NULL'

Using /lib/modules/2.6.15-sigma/kernel/net/ieee80211/ieee80211.ko kobject
ieee80211: registering. parent: <NULL>, set: module

kobject_hotplug

fill_kobj_path: path = '/module/ieee80211'

kobject_hotplug: /sbin/hotplug module seq=660 HOME=/
PATH=/sbin:/bin:/usr/sbin:/usr/bin ACTION=add DEVPATH=/module/ieee80211
SUBSYSTEM=module

kobject_hotplug - call_usermodehelper returned -1

ieee80211: 802.11 data/management/control stack, git-1.1.7

ieee80211: Copyright (C) 2004-2005 Intel Corporation
<[email protected]>

Using /lib/modules/2.6.15-sigma/kernel/drivers/net/wireless/ipw2200.ko
kobject ipw2200: registering. parent: <NULL>, set: module

kobject_hotplug

fill_kobj_path: path = '/module/ipw2200'

kobject_hotplug: /sbin/hotplug module seq=661 HOME=/
PATH=/sbin:/bin:/usr/sbin:/usr/bin ACTION=add DEVPATH=/module/ipw2200
SUBSYSTEM=module

kobject_hotplug - call_usermodehelper returned -1

ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.0.8

ipw2200: Copyright(c) 2003-2005 Intel Corporation

kobject ipw2200: registering. parent: <NULL>, set: drivers

kobject_hotplug

fill_kobj_path: path = '/bus/pci/drivers/ipw2200'

kobject_hotplug: /sbin/hotplug drivers seq=662 HOME=/
PATH=/sbin:/bin:/usr/sbin:/usr/bin ACTION=add
DEVPATH=/bus/pci/drivers/ipw2200 SUBSYSTEM=drivers

kobject_hotplug - call_usermodehelper returned -1

PCI: Enabling device 0000:00:03.0 (0000 -> 0002)

PCI: Setting latency timer of device 0000:00:03.0 to 64

ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection

kobject 0000:00:03.0: registering. parent: firmware, set: class_obj

kobject_hotplug

fill_kobj_path: path = '/class/firmware/0000:00:03.0'

fill_kobj_path: path = '/devices/pci0000:00/0000:00:03.0'

kobject_hotplug - hotplug() returned -19

kobject_hotplug

fill_kobj_path: path = '/class/firmware/0000:00:03.0'

fill_kobj_path: path = '/devices/pci0000:00/0000:00:03.0'

kobject_hotplug: /sbin/hotplug firmware seq=663 HOME=/
PATH=/sbin:/bin:/usr/sbin:/usr/bin ACTION=add
DEVPATH=/class/firmware/0000:00:03.0 SUBSYSTEM=firmware

kobject_hotplug - call_usermodehelper returned -1

kobject_hotplug

fill_kobj_path: path = '/class/firmware/0000:00:03.0'

fill_kobj_path: path = '/devices/pci0000:00/0000:00:03.0'

kobject_hotplug: /sbin/hotplug firmware seq=664 HOME=/
PATH=/sbin:/bin:/usr/sbin:/usr/bin ACTION=remove
DEVPATH=/class/firmware/0000:00:03.0 SUBSYSTEM=firmware

kobject_hotplug - call_usermodehelper returned -1

kobject 0000:00:03.0: cleaning up

ipw2200: ipw-2.4-boot.fw load failed: Reason -2

ipw2200: Unable to load firmware: -2

ipw2200: failed to register network device

ipw2200: probe of 0000:00:03.0 failed with error -5

# 
************************************************************
I use busybox-1.0.0. 

Any other suggestion?

Thanks a lot.
Dennis

-----Original Message-----
From: Zhu Yi [mailto:[email protected]] 
Sent: 2006年12月21日 14:36
To: Dennis Wang
Cc: [email protected]
Subject: Re: [Ipw2100-devel] ipw2200 issue

On Thu, 2006-12-21 at 14:24 +0800, Dennis Wang wrote:
> ipw2200: ipw-2.4-boot.fw load failed: Reason -2
>  
> ipw2200: Unable to load firmware: -2
>  
> ipw2200: failed to register network device
>  
> ipw2200: probe of 0000:00:03.0 failed with error -5
> ****************************************************************
>  
> I use Intel 2915ABG card and used at an embedded system.
> The kernel version is 2.6.15.
> There is no /etc/hotplug directory, and no firmware.agent too.
> I don't know where to place the firmware files, and I place the 
> firmware files to /lib/firmware like at PC.

The old distros put the firmwares in /usr/lib/hotplug/firmware/. See if this
helps.

Thanks,
-yi

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

_______________________________________________
ipw2100-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/ipw2100-devel