Re: Debian 3.1 + kernel 2.6.10 - busy after ATDT

Hi,

it seems that the right country is selected and you have attempted to 
use the 'AT &F X3' init. string without success.

It is possible that this is an IRQ related issue. Since your kernel was 
compiled with ACPI support, please try to boot with the 'pci=noacpi' 
kernel boot parameter to see if there is a difference. This parameter 
will disable to use of ACPI for PCI IRQ routing, which is required on 
some machines.

Regards,


Jonathan
Technical specialist / Linuxant
www.linuxant.com
[email protected]


M. Oujesky wrote:
> Hi,
> 
> I have problems with runnig my HCF PCI modem on Debian 3.1 - Sarge, 
> kernel 2.6.10, using 1.03 hcfpcimodem drivers.
> 
> After the ATDT command, modem ticks three times and returns BUSY.
> (output from gnome-ppp:
>  GNOME PPP: STDERR: --> WvDial: Internet dialer version 1.54.0
>  GNOME PPP: STDERR: --> Initializing modem.
>  GNOME PPP: STDERR: --> Sending: ATX3
>  GNOME PPP: STDERR: ATX3
>  GNOME PPP: STDERR: OK
>  GNOME PPP: STDERR: --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>  GNOME PPP: STDERR: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>  GNOME PPP: STDERR: OK
>  GNOME PPP: STDERR: --> Sending: AT &F X3
>  GNOME PPP: STDERR: AT &F X3
>  GNOME PPP: STDERR: OK
>  GNOME PPP: STDERR: --> Modem initialized.
>  GNOME PPP: STDERR: --> Sending: ATM1L3DT971100811
>  GNOME PPP: STDERR: --> Waiting for carrier.
>  GNOME PPP: STDERR: ATM1L3DT971100811
>  GNOME PPP: STDERR: BUSY
>  GNOME PPP: STDERR: --> The line is busy. Trying again.
>  GNOME PPP: STDERR: --> Sending: ATM1L3DT971100811
>  GNOME PPP: STDERR: --> Waiting for carrier.
>  GNOME PPP: STDERR: ATM1L3DT971100811
>  GNOME PPP: STDERR: BUSY
>  ...
>  ... )
> No matter what program I use for the dialing (wvdial, gnome-ppp, 
> kppp...), the result is still same.
>  
> 
> My box:
>  AMD Athlon 650 MHz
>  Via KX133 chipset (?)
>  Well PCI-RWM-56 HCF based modem
>    (lspci identifies as: "0000:00:08.0 Communication controller: 
> Rockwell International HCF 56k PCI Speakerphone Modem (rev 08)")
> 
> The modem run well on Windows (98, XP) and used to run well on my old 
> Mandrake 9.2-rc2 with 2.4.x kernel. I was using 0.99 drivers there, but 
> I was unable to use them on the new kernel.
> 
> I found similar problems here on the list, and I tried suggested 
> solutions, but none of them worked.
> 
> I'm enclosing the hcfdiag.txt.
> 
> Thanks for any help,
> 
> Mira,
> Czech Republic
> 
> P.S. Sorry for any grammar/spelling/whatever mistakes...
> _______________________________________________
> hcflinux mailing list
> [email protected]
> https://www.linuxant.com/mailman/listinfo/hcflinux