Re: Pulse dialing problem (Asus A2800S laptop)

Hi,

please test under Windows XP on the same machine to see if you have a 
similar problem. You should also send at [email protected] the output 
of 'dumpdiag'. Type the following in a root shell:

---
hsfconfig --dumpdiag
---

Just send us the generated file located in /tmp ('hsfdiag.txt').
It'll help us solve the problem.

Regards,


Jonathan
Technical specialist / Linuxant
www.linuxant.com
[email protected]



Denis Isayev wrote:
> Thank you for quick response!
>      I've issued hsfconfig --country RUSSIA and after this checked 
> region with ATI9 command:
> ATI9
> RUSSIA
> OK
> Also I've changed Init1 in wvdial.conf to AT &F
> and commented Init2 string
> 
> But the result in both cases still the same: modem sends only first 
> digit of the number
> 
> Denis.
> 
> Linuxant support (Jonathan) wrote:
> 
>> Hi,
>>
>> please make sure that the right country is selected with the 
>> 'hsfconfig --country' command in a root shell. You could also try with 
>> the 'AT &F' as the only init. string.
>>
>> Regards,
>>
>>
>> Jonathan
>> Technical specialist / Linuxant
>> www.linuxant.com
>> [email protected]
>>
>>
>>
>> Denis Isayev wrote:
>>
>>>    I have Mandrake 10.1 with kernel 2.6.8.1-12mdk and  
>>> <http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.18.00.03full/hsfmodem-7.18.00.03full_k2.6.8.1_12mdk-1mdk.i586.rpm.zip>hsfmodem-7.18.00.03full_k2.6.8.1_12mdk-1mdk.i586.rpm 
>>> driver installed on my laptop. Driver installation and hsfconfig 
>>> successfuly completed. But when I'm dialing my ISP with ATDP it seems 
>>> that modem dials only first digit of the number and then do nothing 
>>> several minutes until my telephone operator respond with busy tones. 
>>> If I use ATDT command, modem can generate tones for all digits of the 
>>> number, but this is not useful since I have pulse thelephone line :(
>>>    There was a similar problem in  this list 
>>> (http://www.linuxant.com/pipermail/hsflinux/2003q4/001276.html) but 
>>> unfortunately without an answer.
>>>    My modem device identified by scanModem as
>>> ----------------------------------------------------------------------------------- 
>>>
>>> PCIBUS=00:02.6
>>>
>>> Providing detail for device at PCI_bus 00:02.6
>>>  with vendor-ID:device-ID
>>>            ----:----
>>> Class 0703: 1039:7013   Modem: Silicon Integrated Systems [SiS] AC'97 
>>> Modem Controller (rev a0) (prog-if 00 [Generic])
>>>  SubSystem 1043:1816   Asustek Computer, Inc.: Unknown device 1816
>>>        Flags: bus master, medium devsel, latency 32, IRQ 11
>>>        I/O ports at b400 [size=256]
>>>        I/O ports at b000 [size=128]
>>>
>>>                  -----PCI_IDs-------                    --CompilerVer-
>>>    Feature List:  Primary  Subsystem Distr  KernelVer   kernel 
>>> default  CPU
>>> ./scanModem test 1039:7013 1043:1816 mandrake 2.6.8.1-12mdk 3.4.1 
>>> 3.4.1    i686
>>>
>>>  The soft modem Subsystem operates under a controller
>>>   1039:7013  SIS 630
>>> capable of supporting under Linux AT LEAST modem Subsystem chips from 
>>> manufacturers:
>>>        Pctel
>>>        AgereSystems
>>>        Conexant
>>>        Intel
>>>        Smartlink
>>> The modem has a Conexant codec: CXT
>>> and there is support for the modem controller: 1039:7013  SIS 630
>>> ----------------------------------------------------------------------------------- 
>>>
>>>
>>> lspci -v shows the following info:
>>>
>>> Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev 
>>> a0) (prog-if 00 [Generic])
>>>        Subsystem: Asustek Computer, Inc.: Unknown device 1816
>>>        Flags: bus master, medium devsel, latency 32, IRQ 11
>>>        I/O ports at b400 [size=256]
>>>        I/O ports at b000 [size=128]
>>>        Capabilities: [48] Power Management version 2
>>>
>>> ----------------------------------------------------------------------------------- 
>>>
>>>
>>> My wvdial.conf is
>>>
>>> [Dialer Defaults]
>>> Modem = /dev/ttySHSF0
>>> Baud = 57600
>>> Init1 = ATZ
>>> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>>> ISDN = 0
>>> Modem Type = Analog Modem
>>> Phone = 7893727
>>> Username = xxxxx
>>> Password = yyyyy
>>>
>>>
>>> [Dialer zebra]
>>> Dial Command = ATDP
>>>
>>> [Dialer beelineUSB]
>>> Modem = /dev/ttyUSB0
>>> Baud = 115200
>>> Init2 = AT+CGDCONT=1,"IP","internet.beeline.ru"
>>> Carrier Check = no
>>> Phone = *99***1#
>>> Username = beeline
>>> Password = beeline
>>>
>>> ----------------------------------------------------------------------------------- 
>>>
>>>
>>> lastcallstatus is
>>> ----------------------------------------------------------------------------------- 
>>>
>>> <#UG VERSION=3>
>>> <DRIVER VERSION=hsfmodem-7.18.00.03full>
>>> <CALL SETUP RESULT=Detected No Recognizable Tone>
>>> <MULTIMEDIA MODE=Data Only>
>>> <DTE-DCE MODE=Async data>
>>> <V.8 CM="">
>>> <V.8 JM="">
>>> <RX SIG PWR DB=0, TX SIG PWR DB=0, S/N RATIO DB=0>
>>> <RTD=0>
>>> <TX MOD=Unknown, TX SYMBOL RATE=0, TX CARRIER FREQ=0>
>>> <RX MOD=Unknown, RX SYMBOL RATE=0, RX CARRIER FREQ=0>
>>> <TX FIRST RATE=0, RX FIRST RATE=0>
>>> <CARRIER LOSS=0, RATE RENEG=0>
>>> <RETRAINS REQ=0, RETRAINS DET=0>
>>> <TX FINAL RATE=0, RX FINAL RATE=0>
>>> <PROTOCOL=None>
>>> <EC FRAME SIZE=0>
>>> <EC LINK TIMEOUTS=0>
>>> <EC LINK NAKS=0>
>>> <COMPRESSION=None>
>>> <COMPRESSION DICTIONARY SIZE=0>
>>> <TX FLOW CONTROL=0>
>>> <RX FLOW CONTROL=0>
>>> <TX CHARS SENT FROM DTE=2>
>>> <RX CHARS SENT TO DTE=13>
>>> <TX CHARS LOST=0>
>>> <RX CHARS LOST=0>
>>> <TX FRAME COUNT=0>
>>> <RX FRAME COUNT=0>
>>> <TX FRAME ERROR COUNT=0>
>>> <RX FRAME ERROR COUNT=0>
>>> <TERMINATION CAUSE=Key abort>
>>> <CALL WAITING EVENT COUNT=0>
>>> <LSD Vdd=0, Power Bits=0>
>>> <V8BIS DSP VER=0>
>>> <RATE RENEG REQ=0, RATE RENEG DET=0>
>>> <RBS=0, AltRBS=0>
>>> <DIG PAD DET=0, DIG LOSS EST=0, IMD RATIO=0, SPEED DROP=0>
>>> <HS CNT=0, Det1=0, Res1=0, LAPM=0>
>>> <EQM=0, TRAINING EQM=0>
>>> <HandShake Time=0.0>
>>>
>>> <DIB ERROR COUNTERS=0, 0, 0, 0, 0, 0, 0, 0>
>>> ------------------------------------------------------------------------------------------------- 
>>>
>>>
>>> lsmod | grep hsf shows:
>>> ------------------------------------------------------------------------------------------------- 
>>>
>>> hsfusbcd2              56600  0
>>> hsfmc97sis             47536  0
>>> hsfmc97ati             45712  0
>>> hsfmc97ali             52052  0
>>> hsfmc97via             49080  0
>>> hsfmc97ich             50832  0
>>> hsfpcibasic2           56336  0
>>> hsfserial              18916  7 
>>> hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2 
>>>
>>> hsfengine            1299348  1 hsfserial
>>> hsfosspec              81700  12 
>>> hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2,hsfserial,hsfengine 
>>>
>>> hsfsoar                57248  7 
>>> hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2 
>>>
>>> usbcore               103172  10 
>>> hsfusbcd2,hsfosspec,pl2303,usbserial,usbmouse,usbhid,ehci-hcd,ohci-hcd
>>> ---------------------------------------------------------------------------------------------------- 
>>>
>>>
>>> Please let me know I you need any additional info about  this problem.
>>>
>>> Thanks,
>>>    Denis.
>>>
>>> _______________________________________________
>>> hsflinux mailing list
>>> [email protected]
>>> https://www.linuxant.com/mailman/listinfo/hsflinux
>>
>>
> 
> _______________________________________________
> hsflinux mailing list
> [email protected]
> https://www.linuxant.com/mailman/listinfo/hsflinux